Delta 7888 User manual

Conforms to
ASTM F1169-10a Full
Size Crib & F1821
Safety Standards
Style #:
Lot:
Date:
___________
___________
___________
A
4 in 1 Crib
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer Care please reference
the above information. Before contacting Delta Consumer
Care please ensure that the information above matches the
information found on the label on the Crib End bottom rail,
please reference the information found on the product
when contacting Delta Consumer Care.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
December 7, 2012, 23343, R4 ©2012 DELTA ENTERPRISE CORP.

WARNING:
*Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
*Failure to follow these warnings and the assembly instructions could result in serious injury or death.
DO NOT use this crib if you cannot exactly follow the accompanying instructions.
*To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
*Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string
around a child's neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or
attach strings to toys.
*Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of
the body or clothing on loose fasteners.
*Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or
drapes may strangle a child.
*Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out. This crib
has an adjustable mattress support. For the convenience of the parent when the baby is very small, the
mattress support may be used in the highest position. Important: with the mattress support and
mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches
higher than the top surface of the mattress. If it is not, lower the mattress support and the mattress to
the next highest position.
*Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (89cm),
whichever occurs first. The child should be placed in a youth or regular bed.
*Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts,
or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and
other fasteners. Do not use crib if any parts are missing, damaged or broken. Contact Delta
Children's Products for replacement parts and instructional literature if needed. Do not substitute parts.
*Follow warnings on all products in a crib.
*If refinishing, use a non-toxic finish specified for children's products.
*Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
*Infants can suffocate in gaps between crib sides and a mattress that is too small.
*Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that
every component is properly and securely in place.
*To avoid head injury, do not allow any child to play underneath the crib.
*Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
*In Canada Only - Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it
is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the
mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it or
who is taller than 90 cm.
CAUTION:
ANY MATTRESS USED IN THIS CRIB SHALL
BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A
THICKNESS NOT EXCEEDING 6 IN.

3
TODDLER BED
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between bed parts can entrap head and neck of a small child.
NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
The maximum user weight is 50lbs (22.7kg)
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords,
around a child's neck. These items may catch on bed parts.
CAUTION
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress
at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and 4 in (100mm) in
thickness. The mattress thickness must not exceed 6 in (150mm).
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact Delta Children's Products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
A. Top Rail x 2
C. Left Crib End x 1 D. Right Crib End x 1
F. Mattress Support x 1
4
E. Front Side x 1
B. Back Side x 1
G. Stabilizer Bar x 1
POUCH ATTACHED TO MATTRESS SUPPORT
- KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED TO THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
H. Guardrail x 1
Part # 14892
C3. Left Back Post D3. Right Back Post
C1. Left End Panel D1. Right End Panel
C2. Left Front Post D2. Right Front Post
N. M6 x 65 mm Bolt x 10
Used to factory assemble Parts C&D
as originally shipped

PARTS: HARDWARE AND TOOLS.
5
M. Adapter Plate x 2
M4 Allen Wrench Supplied
K. M6 x15 mm Bolt x 4
L. Φ4x30 mm Metal Pin x 4
J. M6 x 45 mm Bolt x 12 No drills necessary. Do not
use power screwdriver.
Part # 5466
Part # 5460
Part # 5493
Part # 1177
Part # 5686

6
Step 1
Section 1: Crib Assembly
Parts and tools required to complete step.
N. M6 x 65 mm Bolt x 10
M4 Allen Wrench
Supplied
C1, D1
C3, D3
C2, D2
NLeft Crib End Shown
N
N
N
N
Parts Pre-Assembled in the facotry, Ensure ALL bolts are TIGHT.
C3. Left Back Post D3. Right Back Post
C1. Left End Panel D1. Right End Panel
C2. Left Front Post D2. Right Front Post
Attach (1) Crib End Panel (Part C1) to (1) Left Back Post (Part C3) and (1) Left Front Post (Part C2)
using(5) M6x65mm Bolts (Part N). Tighten with the M4 Allen Wrench. Repeat on the other Crib End
(Parts D1, D2 &D3).
NOTE: AFTER ASSEMBLY, THE “STEPPED HOLES” IN BOTH POSTS ARE ON THE SAME SIDE.

7
Step 2
Section 1: Crib Assembly
Attach (1) Left Crib End (Part C) and (1) Right Crib End (Part D) to (1) Back Side (Part B) using (4)
M6x45mm Bolts (Part J) and (2) Φ4x30 mm Metal Pin (Part L).
Insert the slot of the Top Rail (Part A) into the tenon on top of the Back Side (Part B), then insert the
M6x45mm Bolts (Part J), through the legs into the flange threaded nuts onto the Top Rail (Part A) as
shown.
Tighten with the M4 Allen Wrench.
NOTE: THE TENON IN PART B MUST FACE UP.
Parts and tools required to complete step.
M4 Allen Wrench
Supplied
J. M6 x 45 mm Bolt x 6
L. Φ4x30 mm Metal Pin x 2
A. Top Rail x 1
B. Back Side x 1
B
D
C
J
J
A
TENON
J
L
L
J
C. Left Crib End x 1
D. Right Crib End x 1

8
Step 3
Section 1: Crib Assembly
Parts and tools required to complete step.
M4 Allen Wrench
Supplied
From Step 1
F. Mattress Support x 1
K. M6 x15 mm Bolt x 4
Attach the Mattress Support (Part F) in all corners using (1) M6x15 mm Bolt (Part K) in each corner.
Tighten with the M4 Allen Wrench.
! WARNINGS ON POUCH MUST FACE UP.
WARNING:
!
!
The Warnings printed on the pouch attached to the
mattress support must face up, the springs must face up.
This crib has (3) adjustment positions, use the highest only
for new borns, move the mattress down as the child grows.
Fall Hazard: When child is able to pull to a standing position,
set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps
for climbing out.
UP
F
ALL CORNERS
K

9
Step 4
Section 1: Crib Assembly
Parts and tools required to complete step.
M4 Allen Wrench
Supplied
From Step 2 J. M6 x 45 mm Bolt x 6
L. Φ4x30 mm Metal Pin x 2
A. Top Rail x 1
E. Front Side x 1
Insert (2) Φ4x30 mm Metal Pin (Part L) into the top hole on each side of the Front Side (Part E),
then attach the Front Side (Part E) to the assemblies from step 2 using (4) M6x45mm Bolts (Part J).
Insert the slot of the Top Rail (Part A) into the tenon on top of the Front Side (Part E), then insert
the M6x45mm Bolts (Part J), through the legs into the flange threaded nuts onto the Top Rail
(Part A) as shown.
Tighten with the M4 Allen Wrench.
TENON
EL
L
E
J
A
J
J
J
J
NOTE :THE TENON INPART H MUST
FACE UP.
PULL GENTLY
PULL GENTLY

10
Step 5
Section 1: Crib Assembly
Parts and tools required to complete step.
Store the assembly instruction booklet in the pouch attached to the mattress support. Store all parts
and tools separately, in a safe place.
WARNING: SEE PAGE 2 FOR INFORMATION
Assembly Instruction
Booklet
Style #:
Lot:
Date:
___________
___________
___________
APRIL7, 2012, 23343, R3 ©2012 DELTAENTERPRISE CORP.
A
4 in 1 Crib
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Crib End
bottom rail.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Due to the presence of small parts during assembly, keep out of
reach of children until assembly is complete.
AI BAG
Style #:
Lot:
Date:
___________
___________
___________
APRIL7, 2012, 23343, R3 ©2012DELTAENTERPRISE CORP.
A
4 in 1 Crib
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
Consumer Care:
www.DeltaChildren.com
DeltaChildren’s Products
114West 26th Street
NewYork, NY 10001
Tele.212-645-9033
FACTORYREV
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
Toregister your product for important safety alerts and updates to your product please
visit www.DeltaChildren.com and click on Product Registration.
When contacting Delta Consumer
Care you will need to reference the
above numbers. They can also be
found on the label on the Crib End
bottom rail.
Read all instructions before assembly and use.
KEEP INSTRUCTIONS FOR FUTURE USE.
ADULT ASSEMBLY REQUIRED
Dueto the presence of small parts during assembly, keep out of
reachof children until assembly is complete.

11
Step 1
Section 2: Toddler Bed Conversion
Parts and tools required to complete step.
M4 Allen Wrench
Supplied
Finished Crib
E
J
J
J
Remove the Top Rail and Front Side installed in step 3 of Section 1 Crib Assembly.
A
J
J
J
PULL GENTLY PULL GENTLY

12
Step 2
Section 2: Toddler Bed Conversion
Parts and tools required to complete step.
M4 Allen Wrench
Supplied
From Step 1
J. M6 x 45 mm Bolt x 2
L. Φ4x30 mm Metal Pin x 2
G
J
J
PULL GENTLY
PULL GENTLY
Attach the Stabilizer Bar (Part G) to the assembly from step 1 using (2) Φ4x30 mm Metal Pins (Part L)
and (2) M6x45 mm Bolts (Part J). Tighten with the M4 Allen Wrench.
G. Stabilizer Bar x 1
G
J
L
BOTH ENDS

13
Step 3
Section 2: Toddler Bed Conversion
Parts and tools required to complete step.
M4 Allen Wrench
Supplied
From Step 2 J. M6 x 45 mm Bolt x 3
Attach the Guardrail (Part H) to the assembly from step 2 using (3) M6x45 mm Bolts (Part J). Tighten
with the M4 Allen Wrench.
H. Guardrail x 1
J
J
H

14
Step 4
Section 2: Toddler Bed Conversion
WARNING:
TODDLER BED WARNINGS
SEE PAGE 3 FOR
The mattress support must be in the lowest positions.
Store all hardware safely.
Read all warnings on page 3.
As shown, use as a day bed or love seat sofa.
Do Not use without stabilizer bar installed.
Stabilizer bar must be used when converted
to a toddler bed.

15
Step 1
Section 3: Full Size Bed Conversion
Parts and tools required to complete step.
M4 Allen Wrench
Supplied
You have the option to convert the crib to a Full Size Bed. Simply follow steps in reverse order to
disassemble the crib. Then remove the rear legs from the Left Crib End and Right Crib End with the M4
Allen Wrench as shown.
Store all parts and hardware in a safe place.

16
Step 2
Section 3: Full Size Bed Conversion
Parts and tools required to complete step.
M4 Allen Wrench
Supplied
To use as a Full Size Bed Headboard only.
Attach (2) Adapter Plates (Part M) to bottom of
Rear Legs using (4) M6x15mm Bolts (Part K).
Hand tighten bolts in place.
Adjust up or down to allow for connection to
Bed Rail. Adapter “Tabs” will keep Adapter Plate
from rotating.
M
M. Adapter Plate x 2
K. M6 x15 mm Bolt x 4
K
M
K
Stand Headboard up. Attach to Bed Frame with
Bolts and Nuts (Supplied by Bed Frame
manufacturer). Adapter Plates (Part M) can be
adjusted up or down to best suit bed frame.
Tighten all bolts once bed rail is adjusted.
NOTE: BED FRAMES ARE NOT SUPPLIED
WITH THIS SYSTEM, BUT CAN BE
PURCHASED AT MATTRESS STORES.

17
Step 3
Section 3: Full Size Bed Conversion
A bed rail system is available to fit your crib to convert to a complete Full Size Bed. Please see your
crib retailer, visit www.DeltaChildren.com or contact Delta Consumer Care for more information.

Warranty: This Delta Crib is warranted to be free from defects for a period
of 1 year from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To register your product for important safety alerts and updates to
your product please visit www.DeltaChildren.com
To report a problem, please log on to www.DeltaChildren.com and
click the Consumer Care Tab, or contact us by phone at
[phone].
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on the Crib End bottom rail.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)
COLOR FTY
REV
STYLE No: 7888 A