Delta 7030 User manual

Conforms to
ASTM F1169-10a Full
Size Crib & F1821
Safety Standards
© 2011 DELTA ENTERPRISE CORP.
22117 AUGUST 3, 2011, R4
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts to the store
from where it was purchased before contacting Delta Children’s Products Customer Service..
Make sure that all preassemble parts are tight. The appearance of your product may be different
from that pictured in this booklet.
To register your product for important safety alerts and updates to your product
please visit www.DeltaChildren.com
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS
DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS BEFORE
ASSEMBLY AND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.
COLOR FTY
REV
STYLE No: 7030 A

WARNING
*Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional
padding under an infant.
*Failure to follow these warnings and the assembly instructions could result in serious injury or death.
*To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
*
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE. Do Not
use this crib if you cannot exactly follow the accompanying instructions
*Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string
around a child's neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or
attach strings to toys.
*Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of
the body or clothing on loose fasteners.
*Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or
drapes may strangle a child.
*Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out. This crib
has an adjustable mattress support. For the convenience of the parent when the baby is very small,
the mattress support may be used in the highest position. Important: with the mattress support and
mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3
inches higher then the top surface of the mattress. If it is not, lower the mattress support and the
mattress to the next highest position.
*Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (90cm),
whichever occurs first. The child should be placed in a youth or regular bed.
*Check this product for damaged hardware, loose joints, missing parts or sharp edges before and
after assembly and frequently during use. Do not use crib if any parts are missing, damaged or
broken. Contact Delta Children's Products for replacement parts and instructional literature if needed.
Do not substitute parts.
*Follow warnings on all products in a crib.
*If refinishing, use a non-toxic finish specified for children's products.
*Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
*Infants can suffocate in gaps between crib sides and a mattress that is too small. Use a crib mattress
that is no thicker than 15 cm and is of such a size that, when it is pushed firmly against any side of the
crib, it does not leave a gap of more than 3 cm between the mattress and any part of the sides of the
crib.
*Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that
every component is properly and securely in place.
*To avoid head injury, do not allow any child to play underneath the crib.
*Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
CAUTION
ANY MATTRESS USED IN THIS CRIB MUST
BE AT LEAST 27 1/4 BY 51 5/8 IN.
(69x131CM) WITH A THICKNESS NOT
EXCEEDING 6 IN (15 CM).

3
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
TODDLER BED
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between bed parts can entrap head and neck of a small child.
NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
The maximum user weight is 50lbs (22.7kg)
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords,
around a child's neck. These items may catch on bed parts.
CAUTION
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress
at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and 4 in (100mm) in
thickness. The mattress thickness must not exceed 6 in (150mm).

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
B. LEFT REAR LEG x 1
C. RIGHT REAR LEG x 1
D. LEFT CRIB
END x 1
K. STABILIZER
BAR x 1
F. MATTRESS SUPPORT x 1
4
G. FRONT RAIL x 1
A. BACK RAIL x 1
H. LEFT FRONT
LEG x 1 J. RIGHT FRONT
LEG x 1
E. RIGHT CRIB
END x 1
INSIDE
OUTSIDE
PRODUCT LABEL
WARNING LABEL
N. M6 x 16 mm BOLT x 8
M4 ALLEN WRENCH
SUPPLIED
P. Φ4 x 30 mm METAL
PIN x 10
L. M6 x 70 mm BOLT x 10
M. M6 x 45 mm BOLT x 10
L
R
L
R
HARDWARE AND TOOLS.
POUCH ATTACHED TO MATTRESS SUPPORT
- KEEP INSTRUCTIONS IN THIS POUCH
AFTER ASSEMBLY.
WARNINGS RELATED TO THE SAFE USE OF
THIS CRIB ARE PRINTED ON THE POUCH.
No drills necessary. Do not
use power screwdriver.

SECTION 1: CRIB ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
5
M4 ALLEN WRENCH
SUPPLIED
L
L
B
C
A. BACK RAIL x 1
B. LEFT REAR LEG x 1
C. RIGHT REAR LEG x 1
L. M6 x 70 mm BOLT x 4
P. Φ4 x 30 mm METAL
PIN x 2
A
L
L
P
P
L
R
R
L
L
R
Attach (1) Left Rear Leg (Part B) and (1) Right Rear Leg (Part C) to the (1) Back Rail (Part A) using
(2) Φ4x30mm Metal Pins(Part P) and (4) M6x70mm Bolts (Part L). Tighten with the M4 Allen Wrench.

SECTION 1: CRIB ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
6
M4 ALLEN WRENCH
SUPPLIED
E
FROM STEP 1 D. LEFT CRIB
END x 1
INSIDE
PRODUCT LABEL
E. RIGHT CRIB
END x 1
OUTSIDE
WARNING LABEL M. M6 x 45 mm BOLT x 4
D
M
M
Attach (1) Left Crib End (Part D) and (1) Right Crib End (Part E) to the assembly from Step 1 using (4)
M6x45 Bolts (Part M). Tighten with the M4 Allen Wrench. When looking at the front, the Left Crib End
must be installed on the left and the Right Crib End must be installed on the right.

SECTION 1: CRIB ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
7
FROM STEP 2
! WARNINGS ON POUCH MUST FACE UP.
F
ALL CORNERS
UP
M4 ALLEN WRENCH
SUPPLIED
N
N. M6 x 16 mm BOLT x 4
F. MATTRESS SUPPORT x 1
Attach the Mattress Support (Part F) in all corners using (1) M6X16 mm Bolt (Part N) in each corner.
Tighten with the M4 Allen Wrench.
WARNING:
!
!
The Warnings printed on the pouch attached to the
mattress support must face up, the springs must face up.
This crib has (3) adjustment positions, use the highest only
for new borns, move the mattress down as the child grows.
Fall Hazard: When child is able to pull to a standing position,
set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps
for climbing out.

SECTION 1: CRIB ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
8
M4 ALLEN WRENCH
SUPPLIED
L
L
H
J
L. M6 x 70 mm BOLT x 6
P. Φ4 x 30 mm METAL
PIN x 8
K
L
G. FRONT RAIL x 1 H. LEFT FRONT
LEG x 1
J. RIGHT FRONT
LEG x 1
K. STABILIZER
BAR x 1
L
G
P
P
L
R
L
L
R
R
P
P
Attach (1) Left Front Leg (Part H) and (1) Right Front Leg (Part J) to the (1) Front Rail (Part G) and
(1) Stabilizer Bar (Part K) using (8) Φ4x30mm Metal Pins (Part P) and (6) M6x70mm Bolts (Part L).
Tighten with the M4 Allen Wrench.

SECTION 1: CRIB ASSEMBLY
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
9
M4 ALLEN WRENCH SUPPLIED
FROM STEP 3
FROM STEP 4
M. M6 x 45 mm BOLT x 6
M
M
M
Attach the assembly from Step 4 to the assembly from Step 3 using (6) M6x45mm Bolts (Part M).
Tighten with the M4 Allen Wrench.

SECTION 1: CRIB ASSEMBLY
STEP 6
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
10
ASSEMBLY INSTRUCTION
BOOKLET
WARNING: SEE PAGE 2 FOR INFORMATION
AI BAG
Store the assembly instruction booklet in the pouch attached to the matress support. Store all parts
and tools separately, in a safe place.
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
©2011 DELTAENTERPRISE CORP.
AUGUST 2, 2011, R4
Consumer Care:
www.DeltaChildren.com
DeltaChildren’s Products
114West 26th Street
NewYork, NY 10001
Tele.212-645-9033
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts to the store
from where it was purchased before contacting Delta Children’s Products Customer Service..
Make sure that all preassemble parts are tight. The appearance of your product may be different
from that pictured in this booklet.
Toregister your product for important safety alerts and updates to your product
please visit www.DeltaChildren.com
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS
DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS BEFORE
ASSEMBLYAND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.
COLOR FTY
REV
STYLE No: 7030 A
Conformsto
ASTMF1169-10a Full
SizeCrib & F1821
SafetyStandards
©2011 DELTAENTERPRISECORP.
AUGUST 2, 2011, R4
Consumer Care:
www.DeltaChildren.com
DeltaChildren’s Products
114West 26th Street
NewYork, NY 10001
Tele.212-645-9033
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DONOT return product parts to the store
from where it was purchased before contacting Delta Children’s Products Customer Service.
.
Make sure that all preassemble parts are tight. Theappearance of your product may be different
from that pictured in this booklet.
Toregister your product for important safety alerts and updates to your product
please visit www.DeltaChildren.com
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS
DURING ASSEMBLY, KEEPOUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS BEFORE
ASSEMBLYAND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.
COLOR FTY
REV
STYLE No: 7030
A

SECTION 2: TODDLER BED CONVERSION
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
11
M4 ALLEN WRENCH
SUPPLIED
G
Remove the Front Rail (Part G only) installed in Step 4 of Section 1 crib assembly. Make sure to leave
Stabilizer Bar (Part K) attached along with Left and Right Front Legs (Part H and J). Make sure to
remove all Metal Dowels (Part P) from top of Stabilizer and Legs.

SECTION 2: TODDLER BED CONVERSION
STEP 2
12
WARNING:
TODDLER BED WARNINGS
SEE PAGE 3 FOR
The mattress support must be in the lowest positions.
Store all hardware safely.
Read all warnings on page 3.
As shown, use as a day bed or love seat sofa.
Do Not use without stabilizer bar intalled.
Stabilizer bar must be used when converted
to a toddler bed.

SECTION 3: FULL SIZE BED CONVERSION
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
13
M4 ALLEN WRENCH SUPPLIED
M
M
M
M
L
L
H
J K
L
L
G
P
P
L
R R
L
P
P
You have the option to convert the crib to a full size bed. Simply follow steps in reverse order to
disassemble the crib. The head board is the back rail assembly done through step 1 of section 1.
To create the footboard, assemble (1) Left Front Leg (Part H) and (1) Right Front Leg (Part J) to the (1)
Front Rail (Part G) and (1) Stabilizer Bar (Part K) using (8) Φ4x30mm Metal Pins (Part P) and (6)
M6x70mm Bolts (Part L). See Section 1 Step 4 for more detail.
Store all parts and hardware in a safe place.

SECTION 3: FULL SIZE BED CONVERSION
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
14
M4 ALLEN WRENCH
SUPPLIED
FROM SECTION 3 STEP 1
NOTE: SHOWN AS A FULL SIZE HEADBOARD AND FOOTBOARD, NOT ALL BED FRAME
SYSTEMS ALLOW USE OF A FOOTBOARD.
N. M6 x 16 mm BOLT x 8
Attach Bed Frame to the Headboard (From Section 3 Step 1) and Footboard (From Section 3 Step 1)
using (8) M6 x 16mm Bolts (Part N). Follow all instructions supplied with the Bed Frame.
Note: Bed Frame system is not included, see your furniture or mattress retailer. Contact Delta
Chidren’s Products for information or with questions.

Warranty: This Delta Crib is warranted to be free from defects for a period
of 1 year from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Consumer Care:
www.DeltaChildren.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
Please do not return this item to the store before contacting
us about missing parts or with any questions.
To register your product for important safety alerts and updates to
your product please visit www.DeltaChildren.com
To report a problem, please log on to www.DeltaChildren.com and
click the Consumer Care Tab, or contact us by phone at
[phone].
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on the Crib End bottom rail.
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)
COLOR FTY
REV
STYLE No: 7030 A