Delta Mission 7532 User manual

SEPTEMBER 3, 2010 7532-R0 ©2010 DELTA ENTERPRISE CORP.
Conforms to
ASTM F2388
Safety Standards
Mission Changer with Casters
STYLE No: 7532
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
To register your product for important safety alerts and updates to your product
please visit www.deltachildrensproducts.com and click on Product Registration.
ADULT ASSEMBLY REQUIRED
DUE TO THE PRESENCE OF SMALL PARTS
DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
READ ALL INSTRUCTIONS BEFORE
ASSEMBLY AND USE.
KEEP INSTRUCTIONS FOR FUTURE USE.
Consumer Care:
www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
When contacting Delta Consumer Care you
will need to reference the above number.
!
FTY
REV
A
COLOR

2
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact delta children's products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.
WARNING:CHANGING TABLE
Fall hazard - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or broken.
Contact Delta Children’s Products with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by Delta Children’s Products.
Always secure the pad to the changing surface by inserting the strap through the hole in the middle of
the pad. See Instructions.

PARTS: MAKE SURE THAT ALL PRE-ASSEMBLED PARTS ARE TIGHT.
A. LEFT END FRAME x 1
3
H. TOP SHELF x 1
J. LOWER SHELF x 2
K. FOAM PAD x 1
B. RIGHT END FRAME x 1
C. TOP RAIL x 2
D. BACK RAIL MID x 1
E. FRONT RAIL TOP x 1
F. FRONT RAIL MID x 1
G. LOWER RAIL x 4
L. RESTRAINT HARNESS x 1

PARTS:
4
M4 ALLEN WRENCH SUPPLIED
P. Φ4x30 mm METAL PIN x 8
M. M6 x 50 mm BOLT x 16
N. M6 x40 mm BOLT x 6
HARDWARE AND TOOLS
T. SHELF BRACE x 1
U. 15mm SCREW x 2
Required Tools
Phillips Screwdriver
Pliers or Adjustable
Wrench Required
for Assembly
(not supplied)
S. NUT x 2
R. NYLON WASHER x 4
V. CASTER x 2
W. LOCKING CASTER x 2

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 1
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
5
ATTACH (1) BACK RAIL MID (PART D), (1) FRONT RAIL TOP (PART E), (1) FRONT RAIL MID
(PART F) AND (4) LOWER RAILS (PART G) TOTHE LEFT END FRAME (PART A) WITH
(2) Φ4x30 mm METAL PINS (PART P) AND (8) M6x50mm BOLTS (PART M) USING THE M4 ALLEN
WRENCH AS SHOWN. BE SURE THE GROOVES FACE TO THE INSIDE.
A
M4 ALLEN
WRENCH SUPPLIED
E
G
A. LEFT END FRAME x 1
D. BACK RAIL MID x 1
E. FRONT RAIL TOP x 1
F. FRONT RAIL
MID x 1
G. LOWER RAIL x 4
P. Φ4x30 mm METAL PIN x 2
M. M6 x 50 mm BOLT x 8
G
F
D
M
M
M
M
M
M
P
P

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 2
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
6
LAY THE LEFT END FRAME ON THE FLOOR, RAILS UP. SLIDE THE TOP SHELF (PART H) IN THE GROOVES
ON THE FRONT RAIL MID AND BACK RAIL MID, INTO THE GROOVE ON THE LEFT END FRAME,
SLIDE (2) LOWER SHELVES (PART J) IN THE GROOVES ON THE LOWER RAILS, INTO THE
GROOVES ON THE LEFT END FRAME AS SHOWN.
FROM STEP 1
J
J
H
H. TOP SHELF x 1 J. LOWER SHELF x 2

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 3
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
7
FROM STEP 2
ATTACH (1) RIGHT END FRAME (PART B) TO THE ASSEMBLY FROM STEP 2 WITH (2)
Φ4x30 mm METAL PINS (PART P) AND (8) M6x50 mm BOLTS (PART M) USING THE M4 ALLEN
WRENCH AS SHOWN.
M4 ALLEN
WRENCH SUPPLIED
B. RIGHT END FRAME x 1
M. M6 x 50 mm BOLT x 8
P. Φ4x30 mm METAL PIN x 2
M
M
M
M
M
M
P
P
B

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 4
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
8
FROM STEP 3
ATTACH (1) SHELF BRACE (PART T) TO THE RAILS USING (2) 15mm SCREWS (PART U). TIGHTEN
WITH THE PHILLIPS SCREWDRIVER.
T
T. SHELF BRACE x 1
U. 15mm SCREW x 2
U

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 5
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
9
FROM STEP 4
ATTACH (2) TOP RAILS (PART C) TO THE ASSEMBLY FROM STEP 4 WITH (4) Φ4x30 mm METAL
PINS (PART P) AND (4) M6x40 mm BOLTS (PART N) USING THE M4 ALLEN WRENCH AS SHOWN.
M4 ALLEN
WRENCH SUPPLIED
P. Φ4x30 mm METAL PIN x 4
N. M6 x40 mm BOLT x 4
C. TOP RAIL x 2
C
C
P
P
N
N
N
N

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 6
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
10
FROM STEP 5
INSERT (2) CASTERS (PART V) AND (2) LOCKING CASTERS (PART W) AS SHOWN.
W
V. CASTER x 2 W. LOCKING CASTER x 2
W
V
FRONT
W
IMPORTANT: MAKE SURE TO PUT
THE LOCKING CASTERS ON THE
FRONT OF THE CHANGER.
Locking
Mechanism

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 7
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
11
FROM STEP 6
M4 ALLEN WRENCH
SUPPLIED
ALIGN THE HOLE IN THE END OF THE STRAP OF THE RESTRAINT HARNESS (PART L) WITH THE HOLE
IN THE TOP SHELF. INSERT (1) M6x40 mm BOLTS (PART N) THROUGH A NYLON WASHER
(PART R), THE RESTRAINT STRAP AND THE HOLE IN THE SHELF. ADD (1) NYLON WASHER
(PART R) WITH A NUT (PART S). HOLD THE NUT WITH A PLIERS OR ADJUSTABLE WRENCH.
REPEAT WITH THE OTHER SIDE OF THE STRAP AS SHOWN.
N. M6 x40 mm BOLT x 2
S. NUT x 2
R. NYLON WASHER x 4
L. RESTRAINT HARNESS x 1
N
L
R
S
R

SECTION 1: CHANGING TABLE ASSEMBLY
STEP 8
PARTS AND TOOLS REQUIRED TO COMPLETE STEP
12
FROM STEP 7
PLACE THE FOAM PAD (PART K) ONTO THE TOP SHELF(PART H) ON TOP OF THE ATTACHED
STRAP FROM STEP 7 AS SHOWN.
K
K. FOAM PAD x 1

SECTION 1: CHANGING TABLE ASSEMBLY
FINAL
TO FASTEN STRAP - PUTH BUCKLE SIDE TOGETH-
ERBESURE BUCKLE IS FULLY FASTENED TO
SECURE CHILD SAFFELY
TO RELEASE PRESS BOTH TABS AND PULL APART
13
RESTRAINT HARNESS SYSTEM USE:
. PLACE THE INFANT ON THE CHANGING TABLE FOAM PAD.
. POSITION THE RESTRAINT HARNESS OVER THE MIDDLE OF THE INFANT’S
TORSO AND INSERT THE BUCKLED ENDS INTO EACH OTHER UNTIL THE LOCK
SHUT WITH A CLICK.
. GENTLY PULL THE LOOSE END OF THE STRAP TO LIGHTLY SNUG THE
RESTRAINT HARNESS AROUND THE INFANT.
MAINTENANCE
. CHECK FASTENERS PERIODICALLY FOR TIGHTNESS. DO NOT OVER TIGHTEN.
THIS MAY CAUSE DISTORTION OR BREAKAGE.
WARNING : FALL HAZARD
ALWAY KEEP CHILD WITHIN ARMS REACH.

Warranty: This Delta product is warranted to be free from defects for a period
of 90 days from the date of purchase under normal use. This warranty extends
only to the original retail purchaser and is valid only when supplied with proof of
purchase, or if received as a gift, when the registration is on file with Delta.
Please do not return this item to the store before contacting
us about missing parts or with any questions.
Customer Service:
Web Site: www.deltachildrensproducts.com
Delta Children’s Products
114 West 26th Street
New York, NY 10001
Tele.212-645-9033
To register your product for important safety alerts and updates to
your product please visit http://deltaenterprise.com/register.asp
To report a problem, please log on to
www.deltachildrensproducts.com and click the Customer Service
Tab, log on to www.deltaenterprise.com/customer_service.asp, or
contact us by phone at [phone].
In the event that you need to contact our customer service
department please have the Style Number and Lot Number available.
Use the space below to make note of those numbers. They can be
found on the label on top shelf.
Style No.:______________________
Lot No. : _______________________
Pack Date:_____________________
Date of Purchase: _____________ (you should also keep your receipt)