Delta SBS 81400-SBS User manual

STEP BY STEP ILLUSTRATED INSTRUCTIONS
READ COMPLETE INSTRUCTIONS BEFORE INSTALLING YOUR
SINGLE HANDLE SINGLE MOUNT WASHERLESS KITCHEN FAUCET
Leave this instruction sheet with installed faucet and write
purchased model number here for future reference!
27816 27816 27816 27816 27816 27816 27816 27816 27816 27816 27816 27816
27816 27816 27816 27816 27816 27816 27816 27816 27816 27816 27816 27816
1
Step 1. S ut off water supply. Remove your
Delta SBS®faucet from t e package. Place base and
gasket on faucet making sure gasket is aligned in
cavity of base. Note: If sink is uneven or gasket does
not properly seal, use of silicone sealant in place of
gasket may be required.
Step 2. Feed tubes down t roug center ole of sink.
Secure faucet to sink wit was er and spacer
(IF REQUIRED), using wrenc .
Step 3. Make connections to water supplies.
IMPORTANT: After installation is complete, remove
aerator, turn andle to full on mixed position. Turn on
water supplies, c eck for leaks and let lines flus for
one minute wit out moving faucet andle. T is will
remove any debris from lines w ic can damage
internal parts of faucet and create leaks. After flus ing
s ut off water at faucet and replace aerator.
INSTALLATION STEPS
IMPORTANT: USE TEFLON® TAPE ON ALL
THREADED CONNECTIONS
RP90
Handle w/Set Screw
RP152
Set Screw
RP50
Cap w/Adjusting Ring
RP4993
Seats & Springs
RP5786
Base w/Gasket
RP6052
Gasket
RP5785
Wrenc
RP61
Cam & Packing
RP250
Adjusting Ring
RP70
Ball Assembly
RP6893
Was er
RP12691
Spacer
RP330
Aerator
RP5861
Nuts
RP5654
Spout
RP25
O-Rings
RP1974
Wrenc
(Accessory Order Only)
T e Delta SBS ® products s own ere are protected by one or more of t e following U.S. Patents: 4,043,359, 3,786,995, 4,562,960, 4,593,430, 4,089,347, 4,218,785, 4,696,322, 4,765,365. More patents are pending.
7/13/01 Rev.B
MODEL 81400-SBS
®
UPC
Limited Warranty
All parts of this Delta SBS ®product are warranted to the original consumer purchaser to be free from defects in material and workmanship for a period of five (5) years from date of purchase as shown on
purchasers receipt.
MASCO PLUMBING PRODUCTS DIVISION will replace, FREE OF CHARGE, during the warranty period, any part which proves defective in material and/or workmanship under normal installation, use, and
service. Replacement parts can be obtained from your dealer or by returning the part to our factory. TRANSPORTATION CHARGES PREPAID, at the address listed on back. THIS WARRANTY IS THE
EXCLUSIVE WARRANTY GRANTED BY MASCO PLUMBING PRODUCTS DIVISION AND IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AND IS FURTHER LIMITED TO DEFECTIVE PARTS REPLACEMENT ONLY. LABOR CHARGES AND/OR DAMAGE INCURRED IN INSTALLATION, REPAIR,
OR REPLACEMENT AS WELL AS INCIDENTAL AND CONSEQUENTIAL DAMAGES CONNECTED THEREWITH ARE EXCLUDED AND WILL NOT BE PAID BY MASCO PLUMBING PRODUCTS DIVISION.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Any damage to this faucet as a result of misuse, abuse,
neglect, accident, improper installation, any use violative of instructions furnished by us, or any use of replacement parts other than genuine Delta parts WILL VOID THE WARRANTY.
®
U
L
®
C
L
A
S
S
I
F
I
E
D
Drinking Water Systems Components
CLASSIFIED BY
UNDER
UNDER
WRITERS LABORATORIES INC.
In Accordance wit Standard
ANSI/NSF 61-97b
21PL
®
CSA B125-93
ASME A112.18.1M-96
®
CSA B125-93
ASME A112.18.1M-96

2
ROUTINE MAINTENANCE
IMPORTANT: AFTER ANY MAINTENANCE BE SURE TO REMOVE
AERATOR AND FLUSH BOTH HOT AND COLD LINES FOR ONE
MINUTE EACH.
Your Delta SBS®washerless faucet will give you years of trouble-free
performance. When maintenance is eventually called for it’s a quick clean job
with one of the inexpensive Delta®repair kits available where you bought your
faucet. The replacement parts in these kits will restore your faucet to the same
condition as the day you bought it.
The Delta SBS®5 year limited warranty on valve mechanism and chrome
plated parts is made possible by superior design, quality parts and careful
workmanship in manufacturing. Should you ever need replacement parts that
are not included in the regular parts kits that are available where you purchased
your faucet, simply write to: MASCO PLUMBING PRODUCTS DIVISION
Customer Service, 55 E. 111th Street, Indianapolis Indiana 46280.
IF FAUCET LEAKS FROM UNDER HANDLE
1. DO NOT SHUT OFF WATER SUPPLIES. Remove andle wit wrenc
(Accessory Order Only).
2. Using wrenc (Accessory Order Only), tig ten adjusting ring until water no
longer leaks around stem of ball w en faucet is on and pressure is exerted to
force ball into socket.1
IF LEAKS PERSISTS—Replace ball assembly–Repair Kit RP70.
1. SHUT OFF WATER SUPPLIES. Remove andle wit wrenc (Accessory
Order Only).
2. Unscrew cap assembly and lift out ball and cam assembly by pulling up on stem.2
3. Slip packing t en cam on new ball and insert into socket.
Reinstall cap and andle.
IF FAUCET LEAKS FROM SPOUT OUTLET–Replace seats and springs,
Repair Kit RP4993.
1. SHUT OFF WATER SUPPLIES. Remove andle wit wrenc (Accessory
Order Only).
2. Unscrew cap assembly and lift out ball and cam assembly by pulling up on stem.2
3. Remove old seats and springs and replace wit new seats and springs. Note:
Refer to insert for proper seat and spring installation. Reassemble faucet in
reverse order.
IF FAUCET LEAKS FROM AROUND SPOUT BODY–Replace O-Rings,
Repair Kit RP25.
1. SHUT OFF WATER SUPPLIES. Remove andle wit wrenc (Accessory
Order Only).
2. Unscrew cap assembly and lift out ball and cam assembly by pulling up on stem.2
3. Gently rotate and lift off spout.
4. Cut and remove O-rings. Stretc new O-rings and snap into grooves on body.
Reassemble faucet in reverse order. Caution: Be careful w en putting spout
back on to gently rotate it until it rests on escutc eon.
1.
1.
2.
1.
2.
2.
3.
3.
4.
1.
3.
2.
IF FAUCET EXHIBITS WATER FLOW REDUCTION
1. Remove aerator and flus faucet, c eck for large debris and replace aerator.
HELPFUL HINTS:
1. Never tig ten cap assembly to stop a leak, always tig ten adjusting ring.
2. Using wrenc (Accessory Order Only), partially unscrew adjusting ring before attempting to remove cap
assembly. Always install cap assembly HAND TIGHT, t en tig ten adjusting ring.
IF REDUCED FLOW IS STILL NOTED—Clear springs of debris and flus
system.
1. SHUT OFF WATER SUPPLIES. Remove andle wit wrenc supplied.
2. Unscrew cap assembly and lift out ball and cam assembly by pulling up on stem.2
3. Remove seats and springs and any debris trapped in springs. IMPORTANT:
USE EXTREME CAUTION. Flus lines by opening water supplies SLIGHTLY!
We recommend placing a bucket over t e valve opening to prevent water spray.
S ut off water supplies and reassemble faucet in reverse order.
1.
3.
2.
CLEANING AND CARE
Your new Delta SBS®faucet is designed and engineered in accordance with the
highest quality and performance standards. With proper care, it will give you
years of trouble-free service. Care should be given to the cleaning of this
product. Although its finish is extremely durable, it can be damaged by harsh
abrasives or polish. To clean, simply wipe gently with a damp cloth and blot dry
with a soft towel.
27816 Rev.B
Inquiries:
55 E. 111th Street
P.O. Box 40980
Indianapolis, Indiana 46280
317/848-1812
®