Deltech Fitness DF832 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
ASSEMBLY INSTRUCTIONS FOR
THE DF832 PEC ATTACHMENT

DF832
HARDWARE
QTY 1
DF832
INSTRUCTIONS
QTY 1
BOX CONTENTS
LEFT HAND ARM
QTY 1
K
RIGHT HAND ARM
QTY 1
J
FIXED PULLEY
BRACKET
QTY 1
B
SWIVEL PULLEY
BRACKET
QTY 2
C
RIGHT HAND CAM
QTY 1
E
LEFT HAND CAM
QTY 1
F
FLOATING PULLEY
BRACKET
QTY 1
G
SWIVEL PULLEY
MOUNT BRACKET
QTY 1
D
BACKREST PAD
QTY 1
I
ARM PAD
QTY 2
H
ARM MOUNT
QTY 1
A
CABLE
QTY 1
L

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
HARDWARE
SLEEVE
QTY 2
M
ARM BUSHING
QTY 4
N
2” SQUARE CAP
QTY 4
O4-1/2” PULLEY
QTY 4
P
M10 x 76MM BOLT
QTY 4
R
M10 x 50MM BOLT
QTY 4
S
M12 x 190MM
BOLT
QTY 2
Q
M10 x 70MM BOLT
QTY 2
T
M8 x 25MM BOLT
QTY 2
U
M12 WASHERS
QTY 4
V
M10 WASHERS
QTY 2
W
M8 WASHERS
QTY 2
X
M19 LOCK NUT
QTY 2
Y
M12 LOCK NUT
QTY 2
Z
M10 LOCK NUT
QTY 8
AA
M8 LOCKNUT
QTY 2
BB

ASSEMBLE THE ARM MOUNT (A) AND THE SWIVEL PULLEY MOUNT BRACKET (D) TO
THE FRONT SUPPORT OF THE LAT MACHINE USING THE M10 x 75MM BOLTS (R), M10
FLAT WASHERS (W) AND M10 LOCK NUTS (AA)
NOTE: THE NUTS USED ON THIS PRODUCT ARE LOCK NUTS SO YOU MUST USE A WRENCH TO TIGHTEN
THE BOLT. THE BOLT MUST GO THRU THE PLASTIC INSERT IN THE NUT.
TOOLS REQUIRED:
WRENCHES OR METRIC SOCKET SET
ARM & PULLEY MOUNT INSTALLATION
FRONT OF MACHINE
D
RW
W
AA
A

INSTALL THE ROLLER PADS (H) ON THE ARMS (K,J). (NOTE IT MAY HELP TO TAKE A
DAMP CLOTH AND WET THE ARM BEFORE SLIDING THE PAD ON THE ARM)
NEXT INSTALL THE CAMS (E,F) ON THE ARMS. THERE IS A LEFT HAND AND A RIGHT
HAND SIDE SO YOU WILL NEED TO LOOK AT THE DIAGRAM TO ENSURE CORRECT
INSTALLATION
NOW INSERT THE 2” CAPS (O) INTO THE WEIGHT ARMS.
NOTE: THE WEIGHT ARMS HAVE BEEN TESTED AT THE FACTORY BEFORE SHIPPING TO
ENSURE THEY WILL FIT INSIDE THE CAM. THIS MAY CAUSE SOME SCRATCHING TO THE
PAINT ON THE WEIGHT ARM BOLT. THIS IS NOT SEEN AFTER INSTALLATION.
CAM & ARM PAD ASSEMBLY
F
E
O
K
J
H
H

INSERT THE ARM BUSHINGS (N) INTO THE ARM MOUNT (A). NOW ASSEMBLE THE WEIGHT
ARMS TO THE ARM MOUNT (A) USING THE M19 LOCKNUTS (Y)
ARM INSTALLLATION
Y
Y
N
N
A

SWIVEL PULLEYASSEMBLY
SWIVEL PULLEY INSTALLATION
ASSEMBLE THE 4 ½” PULLEY (P) INTO
THE SWIVEL PULLEY BRACKET (C)
USING THE M10 x 50MM BOLT (S), M10
WASHERS (W), AND M10 LOCKNUT (AA).
REPEAT FOR OTHER SWIVEL PULLEY
ASSEMBLY.
INSTALL THE SWIVEL PULLEY
ASSEMBLIES TO THE MOUNT
BRACKET USING THE M12 x 190MM
BOLTS (Q), M12 WASHERS (V), AND
M12 LOCKNUTS (Z).
C
PM
S
W
W
AA
QQ
V
V
V
V
Z
Z

ASSEMBLE THE BACKREST PAD (I) TO
THE FRONT SUPPORT OF THE LAT
MACHINE USING THE M8 x 70 BOLTS(T)
AND THE M8 FLAT WASHERS (X). (THE
BOLTS SCREW INTO THREADED INSERTS
PRE-INSTALLED IN THE BACK PAD)
NEXT INSTALL THE FIXED PULLEY
ASSEMBLY USING THE M10 x 75MM
BOLTS (R) M10 FLAT WASHERS (W),
AND M10 LOCKNUTS (AA).
FIXED PULLEYASSEMBLY
INSTALL THE 4 ½” PULLEY(P) INTO THE
FIXED PULLEY BRACKET (B) USING THE
M10 x 50MM BOLT (S) M10 WASHERS (W),
AND M10 LOCK NUT (AA).
FIXED PULLEY & BACKREST INSTALLATION
AA
P
S
WW
B
I
T
T
X
X
R
W
W
W
AA

ASSEMBLE THE 4 ½” PULLEY (P) TO THE FLOATING PULLEY BRACKET (G) USING THE
M10 x 50MM BOLT (S), M10 WASHERS (W) AND M10 NUT (AA).
FLOATING PULLEYASSEMBLY
P
G
W
W
AA
S

FIGURE A
ATTACH THE PEC CABLE TO THE CAM ON THE LEFT SIDE USING THE M8 x 25MM BOLT,
M8 WASHERS , AND M8 LOCKNUT. (SEE FIGURE A)
NOTE: THERE ARE ADJUSTMENT HOLES ON EACH CAM TO COMPENSATE FOR CABLE
STRETCH AFTER THE MACHINE IS USED FOR A WHILE.
RUN THE CABLE THROUGH THE LEFT SIDE SWIVEL PULLEY, DOWN THROUGH THE
FLOATING PULLEY, UP THROUGH THE RIGHT SIDE SWIVEL PULLEY AND ATTACH TO
RIGHT CAM.
TIGHTEN THE BOLTS ON THE SWIVEL PULLEYS.
SWIVEL PULLEY ASSEMBLIES
FLOATING PULLEY ASSEMBLY
CABLE INSTALLATION

DISCONNECT THE LOWER CABLE ALREADY ATTACHED TO THE MACHINE AND RUN IT
THOUGH THE FIXED PULLEY AND RE-ATTACH IT TO THE RING AT THE BOTTOM OF THE
FLOATING PULLEY ASSEMBLY.
MAKE SURE ALL YOUR BOLTS ARE TIGHT BEFORE USE. CHECK THEM PERIODICALLY
TO MAKE SURE THEY ALWAYS STAY TIGHT.
DISCONNECT
LOWER CABLE
FROM HERE
RE-ATTACH LOWER
CABLE HERE
CABLE INSTALLATION

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OF WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE

T-SHIRT ORDER FORM
DELTECH FITNESS T - SHIRT
SIZES AVAILABLE ARE M-XXL. THE COLOR
OF THE SHIRTS ARE WHITE. RED AND BLACK
LOGO. ONLY $12.99
DELTECH FITNESS MUSCLE SHIRT
SIZES AVAILABLE M-XXL THE COLOR
AVAILABLE IS BLACK. RED AND WHITE
LOGO. ONLY $12.99
SEND TO: DELTECH MANUFACTURING, INC.
3910 OAKLAWN DR.
LOUISVILLE, KY. 40219
ALL ORDERS SHIPPED UPS GROUND.
MAKE CHECK OR MONEY ORDER PAYABLE TO: DELTECH MANUFACTURING
KENTUCKY RESIDENTS ADD 6% SALES TAX. ALLOW 3 WEEKS FOR DELIVERY.
PRICE INCLUDES SHIPPING TO THE CONTIGUOUS UNITED STATES
OR ORDER ONLINE WITH A CREDIT CARD AT WWW.FITNESSDESTINATION.COM
SHIPPING INFORMATION:
QTY SIZE DESCRIPTION COLOR PRICE TOTAL
T - SHIRT WHITE $12.99 EA.
MUSCLE SHIRT BLACK $12.99 EA.
TOTAL

Exercise Chart for the DF906
Low Row
Start Finish
Start Finish
Lat Pull
Start Finish
Curl
Shrug
Start Finish
Row Tri Pull
Rev Curl
Start FinishStart Finish Start Finish
Start Finish Start Finish
Squat Side Row
NOT ALL EXERCISES ARE RECOMMENDED FOR EVERYONE PLEASE CONSULT A PHYSICIAN BEFORE STARTING ANY EXERCISE PROGRAM