Deltran Battery Tender 1000Amp User manual

1
1000Amp Vehicle Jump Starter &
Portable Power Bank
INSTRUCTION MANUAL
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
390-0425-R0
2
CONTENTS
Important Safety Instructions & Warnings ……………….....
Product Specifications…………………………………………..
Product Overview…………………………………………………
Operating Instructions .….………….…………………………..
User Maintenance Instructions………………..……………….
Trouble Shooting ………………………………………………..
Regulatory Warnings………………………………………..…..
Customer Service…………………………………………………
Warranty…………………………………………………………….
3
6
6
7
11
11
12
13
13

1
1000Amp Vehicle Jump Starter &
Portable Power Bank
INSTRUCTION MANUAL
Read this material before using this product.
Failure to do so can result in serious injury.
Save this manual.
390-0425-R0
2
CONTENTS
Important Safety Instructions & Warnings ……………….....
Product Specifications…………………………………………..
Product Overview…………………………………………………
Operating Instructions .….………….…………………………..
User Maintenance Instructions………………..……………….
Trouble Shooting ………………………………………………..
Regulatory Warnings………………………………………..…..
Customer Service…………………………………………………
Warranty…………………………………………………………….
3
6
6
7
11
11
12
13
13

3
IMPORTANT SAFETY INSTRUCTIONS
WARNING When using this product, basic precautions should always be
followed. Including the following:
1. Save these instructions.
2. Read all the instructions before using the product.
3. To reduce the risk of injury, close supervision is necessary when the product
is used near children.
4. Do not put fingers or hands into the product.
5. Use of an attachment not recommended or sold by the power pack
manufacture may result in a risk of fire, electric shock, or injury to person.
6. To reduce the risk of damage to the electric plug, pull on the plug rather that
the cords when disconnecting the power pack.
7. Do not use a battery pack or appliance that is damaged or modified.
Damaged or modified batteries may exhaust unpredictable behavior resulting
in fire, explosion or risk of injury.
8. Do not operate the power pack with a damaged cord or plug.
9. Do not disassemble the power pack, only a qualified service technician
should service the product. Incorrect reassembly may result in a risk of fire or
electric shock.
10. To reduce the risk of electric shock, unplug the power pack from the outlet
before attempting any instructed servicing.
WARNING RISK OF EXPLOSIVE GASES
1. WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS DANGEROUS.
BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL
BATTERY OPERATION. FOR THIS REASON, IT IS THE UTMOST
IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME
YOU USE THE POWER PACK.
2. To reduce the risk of battery explosion, follow these instructions and those
published by the battery manufacture and manufacture of any equipment you
intend to use in the vicinity of the battery. Review all cautionary marking on
these products and on engine.
4
PERSONAL PRECAUTIONS
1. Consider having someone close enough by to come to your aid when
working near lead-acid battery.
2. Have plenty of fresh water and soap nearby in case battery acid contacts
skin, clothing, or eyes.
3. Wear complete eye protection and clothing protection. Avoid touching eyes
while working near battery.
4. If battery acid contacts skin or clothing, wash immediately with soap and
water. If acid enters eye, immediately flood eye with cold water for at least
10 minutes and get medical attention.
5. NEVER smoke or allow a spark or flame in vicinity of battery or engine.
6. Be extra cautious to reduce the risk of dropping a metal tool onto the
battery. It might spark or short-circuit battery or other electrical part that
may cause explosion.
7. Remove personnel metal items such as rings, bracelets, and watches when
working with a lead-acid battery. A lead-acid battery can produce a
short-circuit current high enough to weld a ring or the like to metal, causing
severe burn.
WARNING
1. When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
2. Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burn.
3. Do not expose a power pack to fire or excessive temperature. Exposure to
fire or temperature above 130°C may cause explosion.
4. Have servicing performed by a qualified technician using only factory
replacement parts.

3
IMPORTANT SAFETY INSTRUCTIONS
WARNING When using this product, basic precautions should always be
followed. Including the following:
1. Save these instructions.
2. Read all the instructions before using the product.
3. To reduce the risk of injury, close supervision is necessary when the product
is used near children.
4. Do not put fingers or hands into the product.
5. Use of an attachment not recommended or sold by the power pack
manufacture may result in a risk of fire, electric shock, or injury to person.
6. To reduce the risk of damage to the electric plug, pull on the plug rather that
the cords when disconnecting the power pack.
7. Do not use a battery pack or appliance that is damaged or modified.
Damaged or modified batteries may exhaust unpredictable behavior resulting
in fire, explosion or risk of injury.
8. Do not operate the power pack with a damaged cord or plug.
9. Do not disassemble the power pack, only a qualified service technician
should service the product. Incorrect reassembly may result in a risk of fire or
electric shock.
10. To reduce the risk of electric shock, unplug the power pack from the outlet
before attempting any instructed servicing.
WARNING RISK OF EXPLOSIVE GASES
1. WORKING IN THE VICINITY OF A LEAD ACID BATTERY IS DANGEROUS.
BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL
BATTERY OPERATION. FOR THIS REASON, IT IS THE UTMOST
IMPORTANCE THAT YOU FOLLOW THE INSTRUCTIONS EACH TIME
YOU USE THE POWER PACK.
2. To reduce the risk of battery explosion, follow these instructions and those
published by the battery manufacture and manufacture of any equipment you
intend to use in the vicinity of the battery. Review all cautionary marking on
these products and on engine.
4
PERSONAL PRECAUTIONS
1. Consider having someone close enough by to come to your aid when
working near lead-acid battery.
2. Have plenty of fresh water and soap nearby in case battery acid contacts
skin, clothing, or eyes.
3. Wear complete eye protection and clothing protection. Avoid touching eyes
while working near battery.
4. If battery acid contacts skin or clothing, wash immediately with soap and
water. If acid enters eye, immediately flood eye with cold water for at least
10 minutes and get medical attention.
5. NEVER smoke or allow a spark or flame in vicinity of battery or engine.
6. Be extra cautious to reduce the risk of dropping a metal tool onto the
battery. It might spark or short-circuit battery or other electrical part that
may cause explosion.
7. Remove personnel metal items such as rings, bracelets, and watches when
working with a lead-acid battery. A lead-acid battery can produce a
short-circuit current high enough to weld a ring or the like to metal, causing
severe burn.
WARNING
1. When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
2. Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery may
cause irritation or burn.
3. Do not expose a power pack to fire or excessive temperature. Exposure to
fire or temperature above 130°C may cause explosion.
4. Have servicing performed by a qualified technician using only factory
replacement parts.

5
5. Attach output cables to the battery and chassis as indicted below. Never
allow the output clamps to touch one another.
a) Check the battery level of the Jump Pack.
b) Insert the smart alligator clip connector into the end of the Jump Pack.
c) Connect the RED positive clip to the positive post on the battery, then
the BLACK negative clip to the negative post on the battery.
d) If connected correctly the LED should turn green. Wait 5 to 10 seconds
then start your vehicle.
e) Remove the clips immediately after the vehicle has started.
CAUTION
1) Do not immerse in water.
2) Do not use or store the VEHICLE JUMP STARTER near sources of fire or
heater.
3) Do not put the VEHICLE JUMP STARTER into a fire or apply direct heat to
it.
4) Do not pierce the VEHICLE JUMP STARTER casing.
5) Do not strike, throw, or subject the VEHICLE JUMP STARTER to severe
physical shock.
6) Do not attempt to modify the VEHICLE JUMP STARTER in any way.
7) Do not place the VEHICLE JUMP STARTER in a microwave oven or
pressurized container.
8) Do not use the VEHICLE JUMP STARTER if it gives off an odor or
generates heat
9) Do not insert any metal object into the cable input opening as this could
cause a spark and electric shock.
10) Do not use the VEHICLE JUMP STARTER as a battery charger or power
supply.
6
PRODUCT SPECIFICATIONS
Vehicle Jump Starter & Portable Power Bank
Standard USB Output port 5VDC, 2.4Amp
Type – C USB, In (Out) port 5VDC, 3Amp
pmA2,CDV5troptupnIBSUorciM
t *taW01Up toiQ-gnigrahCsseleriW
Start Current/Peak Current 400Amp/1000Amp
HW-1101-030rebmuNtraPledoM
Operating Temperature 32°F -104°F (0°C - 40°C)
raey1ytnarraW
Certification UL 2743, CEC, DOE, FCC, ICES-001
3.83NUnoitatropsnarT
PRODUCT OVERVIEW
Below is a list of items that should be included in your retail box:
1) Vehicle Jump Starter & Portable Power Bank
2) Smart Alligator Clips
3) Micro USB Charging Cable
4) USB Wall Charger
5) Carry Bag
6) Instruction Manual
* Depending on the device being charged, some devices do not support
wireless charging up to 10 watts.

5
5. Attach output cables to the battery and chassis as indicted below. Never
allow the output clamps to touch one another.
a) Check the battery level of the Jump Pack.
b) Insert the smart alligator clip connector into the end of the Jump Pack.
c) Connect the RED positive clip to the positive post on the battery, then
the BLACK negative clip to the negative post on the battery.
d) If connected correctly the LED should turn green. Wait 5 to 10 seconds
then start your vehicle.
e) Remove the clips immediately after the vehicle has started.
CAUTION
1) Do not immerse in water.
2) Do not use or store the VEHICLE JUMP STARTER near sources of fire or
heater.
3) Do not put the VEHICLE JUMP STARTER into a fire or apply direct heat to
it.
4) Do not pierce the VEHICLE JUMP STARTER casing.
5) Do not strike, throw, or subject the VEHICLE JUMP STARTER to severe
physical shock.
6) Do not attempt to modify the VEHICLE JUMP STARTER in any way.
7) Do not place the VEHICLE JUMP STARTER in a microwave oven or
pressurized container.
8) Do not use the VEHICLE JUMP STARTER if it gives off an odor or
generates heat
9) Do not insert any metal object into the cable input opening as this could
cause a spark and electric shock.
10) Do not use the VEHICLE JUMP STARTER as a battery charger or power
supply.
6
PRODUCT SPECIFICATIONS
Vehicle Jump Starter & Portable Power Bank
Standard USB Output port 5VDC, 2.4Amp
Type – C USB, In (Out) port 5VDC, 3Amp
pmA2,CDV5troptupnIBSUorciM
t *taW01Up toiQ-gnigrahCsseleriW
Start Current/Peak Current 400Amp/1000Amp
HW-1101-030rebmuNtraPledoM
Operating Temperature 32°F -104°F (0°C - 40°C)
raey1ytnarraW
Certification UL 2743, CEC, DOE, FCC, ICES-001
3.83NUnoitatropsnarT
PRODUCT OVERVIEW
Below is a list of items that should be included in your retail box:
1) Vehicle Jump Starter & Portable Power Bank
2) Smart Alligator Clips
3) Micro USB Charging Cable
4) USB Wall Charger
5) Carry Bag
6) Instruction Manual
* Depending on the device being charged, some devices do not support
wireless charging up to 10 watts.

 7

OPERATING INSTRUCTIONS
VEHICLE JUMP STARTER & PORTABLE POWER BANK FEATURES
8

JUMP STARTING A VEHICLE
1) Before jump starting your particular vehicle always check the manufacturer
instructions/recommendations/warnings first.
2) Check the battery level of the Vehicle Jump Pack by pressing the ON/OFF
button before jump starting your vehicle. There must be at least 50% of
battery level available.
3) Insert the smart alligator clip connector into the end of the Jump Pack.
4) Connect the RED positive clip to the positive post on the battery, then the
BLACK negative clip to the negative post on the battery.
5) CAUTION: Ensure the Vehicle Jump Pack and smart alligator clip cables are
clear of all vehicle fan blades/belts/pulleys etc. before proceeding.
6) The LED on the smart alligator clips will then turn GREEN. Wait 5 to 10
seconds then start your vehicle
7) Remove the clips IMMEDIATELY after the vehicle has started. Black negative
clamp first.
8) DO NOT use the Vehicle Jump Starter to repeatedly try and start your vehicle.
Wait at least thirty (30) seconds between attempts. Check vehicle after three
attempts.

 7

OPERATING INSTRUCTIONS
VEHICLE JUMP STARTER & PORTABLE POWER BANK FEATURES
8

JUMP STARTING A VEHICLE
1) Before jump starting your particular vehicle always check the manufacturer
instructions/recommendations/warnings first.
2) Check the battery level of the Vehicle Jump Pack by pressing the ON/OFF
button before jump starting your vehicle. There must be at least 50% of
battery level available.
3) Insert the smart alligator clip connector into the end of the Jump Pack.
4) Connect the RED positive clip to the positive post on the battery, then the
BLACK negative clip to the negative post on the battery.
5) CAUTION: Ensure the Vehicle Jump Pack and smart alligator clip cables are
clear of all vehicle fan blades/belts/pulleys etc. before proceeding.
6) The LED on the smart alligator clips will then turn GREEN. Wait 5 to 10
seconds then start your vehicle
7) Remove the clips IMMEDIATELY after the vehicle has started. Black negative
clamp first.
8) DO NOT use the Vehicle Jump Starter to repeatedly try and start your vehicle.
Wait at least thirty (30) seconds between attempts. Check vehicle after three
attempts.

9
SMART ALLIGATOR CLIPS
The smart alligator clips contain a single Amber/Green LED along with a warning
buzzer for Faults and Error protection:
1) If connected correctly the LED on the smart alligator clips should turn
green.
1) Standby Mode – Clips are not connected – The Green LED Flashes.
2) Vehicle battery voltage to LOW - Amber LED On, buzzer is beeping
3) Vehicle battery voltage to HIGH - Amber LED On, buzzer On solid.
4) Alligator clips connected to vehicle battery in reverse polarity. (Red clip to
Black negative terminal, Black clip to Red positive terminal). Amber LED
On, buzzer is beeping.
5) Short circuit protection - Amber LED On, buzzer is beeping.
6) Over heat protection – Amber LED is Flashing, buzzer is beeping.
CHARGING THE VEHICLE JUMP STARTER & PORTABLE POWER BANK
1) Use the supplied micro USB cable and wall charger if needed to charge the
Vehicle Jump Starter & Portable Power Bank.
NOTE: While charging all of the other features and functions are NOT
active.
2) When charging “IN” will appear above the percentage of charge digits and
the second percentage digit will flash on the LCD display.
3) Once the internal battery level has reached 100% the charge is complete
and the unit will turn off after 10 seconds.
4) The battery level should be checked and charged every three (3) months.
5) DO NOT use any other charger to charge this Vehicle Jump Starter &
Portable Power Bank.
6) Doing so can damage the internal battery and also be very dangerous.
7) When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
10
WIRELESS PHONE CHARGING
1) Press the ON/OFF button, the LED display will illuminate showing the
Icon flashing.
2) Place the back of your phone onto the unit. The Icon will turn solid and
your phone will then be charging.
3) Make sure there are no extra obstructions (apart from the case) on the
back of your phone.
CAUTION
1) The device shall be stored indoors and protected from the elements.
2) The unit shall not be charged outdoors.
3) When in use, steps should be taken to reduce the exposure to rain, sleet,
snow, and the like.
USB PORTS
1) There are three (3) USB ports contained in your Jump Starter & Portable
Power Bank. Once your device is connected you must press the ON/OFF
button to activate charging.
a. Standard USB Output port - 5VDC/2.4Amp. Used to charge your cell
phone, tablet etc.
b. Type – C USB, In (Out) port – 5VDC/3Amp. This can power a tablet,
power pack, smart phone, camera etc.
c. Micro USB Input port – 5VDC/2A. This port is for charging your Jump
Starter & Portable Power Bank. Only use the supplied cable to charge
your Jump Starter & Portable Power Bank.
LED FLASH LIGHTS
1) To turn the LED lights ON simply hold the ON/OFF Button down for at least
two (2) seconds.
2) To turn the LED lights OFF hold the ON/OFF Button down for at least two
(2) seconds.

9
SMART ALLIGATOR CLIPS
The smart alligator clips contain a single Amber/Green LED along with a warning
buzzer for Faults and Error protection:
1) If connected correctly the LED on the smart alligator clips should turn
green.
1) Standby Mode – Clips are not connected – The Green LED Flashes.
2) Vehicle battery voltage to LOW - Amber LED On, buzzer is beeping
3) Vehicle battery voltage to HIGH - Amber LED On, buzzer On solid.
4) Alligator clips connected to vehicle battery in reverse polarity. (Red clip to
Black negative terminal, Black clip to Red positive terminal). Amber LED
On, buzzer is beeping.
5) Short circuit protection - Amber LED On, buzzer is beeping.
6) Over heat protection – Amber LED is Flashing, buzzer is beeping.
CHARGING THE VEHICLE JUMP STARTER & PORTABLE POWER BANK
1) Use the supplied micro USB cable and wall charger if needed to charge the
Vehicle Jump Starter & Portable Power Bank.
NOTE: While charging all of the other features and functions are NOT
active.
2) When charging “IN” will appear above the percentage of charge digits and
the second percentage digit will flash on the LCD display.
3) Once the internal battery level has reached 100% the charge is complete
and the unit will turn off after 10 seconds.
4) The battery level should be checked and charged every three (3) months.
5) DO NOT use any other charger to charge this Vehicle Jump Starter &
Portable Power Bank.
6) Doing so can damage the internal battery and also be very dangerous.
7) When charging the internal battery, work in a well ventilated area and do
not restrict ventilation in any way.
10
WIRELESS PHONE CHARGING
1) Press the ON/OFF button, the LED display will illuminate showing the
Icon flashing.
2) Place the back of your phone onto the unit. The Icon will turn solid and
your phone will then be charging.
3) Make sure there are no extra obstructions (apart from the case) on the
back of your phone.
CAUTION
1) The device shall be stored indoors and protected from the elements.
2) The unit shall not be charged outdoors.
3) When in use, steps should be taken to reduce the exposure to rain, sleet,
snow, and the like.
USB PORTS
1) There are three (3) USB ports contained in your Jump Starter & Portable
Power Bank. Once your device is connected you must press the ON/OFF
button to activate charging.
a. Standard USB Output port - 5VDC/2.4Amp. Used to charge your cell
phone, tablet etc.
b. Type – C USB, In (Out) port – 5VDC/3Amp. This can power a tablet,
power pack, smart phone, camera etc.
c. Micro USB Input port – 5VDC/2A. This port is for charging your Jump
Starter & Portable Power Bank. Only use the supplied cable to charge
your Jump Starter & Portable Power Bank.
LED FLASH LIGHTS
1) To turn the LED lights ON simply hold the ON/OFF Button down for at least
two (2) seconds.
2) To turn the LED lights OFF hold the ON/OFF Button down for at least two
(2) seconds.

11
TROUBLE SHOOTING
USER MAINTENANCE INSTRUCTIONS
1) The battery level should be checked and the Vehicle Jump Starter &
Portable Power Bank should be charged every three (3) months. Keeping
the internal battery fully charged will ensure the Vehicle Jump Starter &
Portable Power Bank in ready to use when needed. This will also extend
the life of the internal battery.
2) Store the Vehicle Jump Starter & Portable Power Bank in a clean dry
environment at room temperature if possible.
3) If you see a bulge in the case or notice a chemical smell STOP using the
Vehicle Jump Starter & Portable Power Pack immediately and seek
technical help.
NOITULOSMELBORP
The vehicle will not start
Check the connection of the alligator
clips to the battery terminals and
ensure the LED is solid green and not
flashing on the smart alligator clips.
Ensure you have a minimum of two
blue LED’s illuminated.
Vehicle battery voltage to low
After connecting the smart alligator
clips wait a couple of minutes before
attempting to start the vehicle.
Vehicle Jump Pack & Portable Power
Bank will not charge
Check the cable and connection and
also try charging a different device.
12
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.

11
TROUBLE SHOOTING
USER MAINTENANCE INSTRUCTIONS
1) The battery level should be checked and the Vehicle Jump Starter &
Portable Power Bank should be charged every three (3) months. Keeping
the internal battery fully charged will ensure the Vehicle Jump Starter &
Portable Power Bank in ready to use when needed. This will also extend
the life of the internal battery.
2) Store the Vehicle Jump Starter & Portable Power Bank in a clean dry
environment at room temperature if possible.
3) If you see a bulge in the case or notice a chemical smell STOP using the
Vehicle Jump Starter & Portable Power Pack immediately and seek
technical help.
NOITULOSMELBORP
The vehicle will not start
Check the connection of the alligator
clips to the battery terminals and
ensure the LED is solid green and not
flashing on the smart alligator clips.
Ensure you have a minimum of two
blue LED’s illuminated.
Vehicle battery voltage to low
After connecting the smart alligator
clips wait a couple of minutes before
attempting to start the vehicle.
Vehicle Jump Pack & Portable Power
Bank will not charge
Check the cable and connection and
also try charging a different device.
12
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.

13
CUSTOMER SERVICE
WARRANTY
For customer support please visit batterytender.com. You can also call our
customer service hotline [phone]
The Battery Tender®Jump Starter & Portable Power Pack comes with a twelve
(12) month limited warranty against defects or failure (within one (1) year of
purchase).
THIS LIMITED WARRANTY IS VOID under the following conditions:
1) The product is misused, subjected to careless handling, or operated under
conditions of extreme temperature, shock, or vibration beyond our
recommendations for safe and effective use.
2) The product is disassembled or repaired by anyone who is not an
authorized service representative of Battery Tender®
3) The product was purchased from an unauthorized source. Warranty is not
transferable from the original purchaser.
4) Any physical damage to any of components or any accessory after
purchase.
5) Any modifications to any of the components.
6) Any corrosion including salt water.