Deluce lighting Dlpan10wblkdl User manual

IMPORTANT INSTALLATION INFORMATION

• Installation should be carried out in accordance with the latest

edition of the IEE Wiring Regulations (BS7671) and taking into

consideration the latest Building Regulations. If in doubt, consult a

qualified electrician.

• Important: Ensure that ALL electrical connections are tight with no

loose strands including factory made connections.

• Before commencing any installation or maintenance work,

ensure electricity is switched off at the mains.

• Please take note of the maximum rated voltage for your floodlight.

PLEASE NOTE THIS FLOODLIGHT IS MULTI-VOLTAGE - AN

APPROPRIATE 110V STEP-DOWN TRANSFORMER MUST BE

USED WHEN USING THE FLOODLIGHT ON SITE.

NOT PIR VERSION, PIR VERSION IS 230-240V ONLY.

• Please take note of the IP (Ingress Protection) rating of your

floodlight when deciding location.

• Always allow sufficient slack in the supply cable in order to remove

the floodlight from its position for any future maintenance.

• Care must be taken for installations where the lens or bezel may

come into contact with bare skin.

• Please take note of the nearest illuminated surface as detailed on

the product label.

• Always check whether the site of the installation can

support the weight of the floodlight.

For safety, 1.5 times the weight of the floodlight is

recommended. If you are unsure do not install.

GENERAL INSTALLATION

1. Please make sure you are safe when working at height.

2. Employ the latest safety regulations and procedures to ensure the

safe installation of this floodlight.

3. When positioning your floodlight out of doors please take note that

outdoor electrical installations should be installed by a qualified

Electrician. Correct circuit protection for all exterior electrical services

should include a residual current device (RCD), also known as an

earth leakage circuit breaker (ELCB). This simple device ensures that

the power is cut off immediately; it detects a leakage of current

to earth, which indicates an electrical fault which is potentially

threatening to life.

Observe these few Simple rules and keep your outdoor electrical

installation safe.

INSTALLATION INSTRUCTIONS

1. Select the required position for the floodlight.

2. Remove the mounting bracket from the floodlight.

3. Fix the mounting bracket to the mounting surface with appropriate

screws and wall plugs, sufficient to take the weight of the fitting.

4. Replace the main body of the floodlight to the bracket, ensuring

that cables are not trapped between the base mounting bracket and

the floodlight,

5. Connect the floodlight to the mains supply, with an appropriate

junction box or connection fitting, making sure any exposed

connections and joints are sufficiently weatherproofed.

When using with 110V supply make sure the correct CEE plug is

fitted to connect to the transformer - NOT PIR Version.

6. Then make the electrical connections as follows:

LIVE - (Red or Brown) to a terminal marked L

NEUTRAL - (Black or Blue) to a terminal marked N

EARTH - (Green/Yellow) to a terminal marked

WARNING - THIS FITTING MUST BE EARTHED

7. Ensure that there are no exposed conductors, loose or trapped cable

strands.

8. Adjust the angle of the floodlight by the retaining/adjustment bolt,

making sure the bolt is re-tightened.

9. Switch on the power supply to test.

MOUNTING

BRACKET

MOUNTING BRACKET RETAINING/

ADJUSTMENT BOLT

LED PANTHER

FLOODLIGHT FITTING

INSTRUCTIONS

DEL0585a/Feb_2016/issue_1 page 1 of 2

www.delucelighting.com

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION

LEAVE A COPY FOR THE USER/MAINTENANCE ENGINEER FOR FUTURE REFERENCE

We recommend this ﬁtting is installed by a qualiﬁed Electrician.

100-240V LED IP 65Standard

PIR 230-240V LED IP 44

These instructions are for the Déluce Lighting Panther LED Floodlights :

DLPAN10WBLKDL, DLPAN10WBLKWW, DLPAN10WBLKDLPIR, DLPAN10WBLKWWPIR, DLPAN20WBLKDL, DLPAN20WBLKWW,

DLPAN20WBLKDLPIR & DLPAN20WBLKWWPIR DLPAN30WBLKDL, DLPAN30WBLKWW, DLPAN30WBLKDLPIR, DLPAN30WBLKWWPIR,

DLPAN50WBLKDL, DLPAN50WBLKWW, DLPAN50WBLKDLPIR & DLPAN50WBLKWWPIR

On the base of the PIR there are three (3) dials:

PIR ADJUSTMENT (FOR PIR MODELS)

TIME LUXSENS

RANGE ADJUSTMENT

The PIR sensor is situated on a moveable joint.

The sensor range can be adjusted by moving the PIR both

vertically and horizontally.

Please be aware that PIR detectors are more sensitive

to movement across them than they are to movement

towards them. This should be considered when

positioning during installation.

SPECIFICATIONS

Detection Method: Passive infrared sensor

Time Adjustment: 5 seconds to 8 minutes (approx)

Power Consumption: 6 Watts maximum for the sensor

unit only

Sensor Range ( SENS )

This dial sets the floodlight’s sensitivity to movement.

Turning the dial clockwise will adjust the sensitivity range,

as follows :

up to 10mtrs x 140° degree spread (approx).

TIME DIAL ( TIME )

This dial controls how long the light will remain on once

activated.

It will operate from 5 Seconds to 8 Minutes. Turning the

dial fully clockwise will set the unit to it longest time

setting and fully anti-clockwise will set it at its shortest

setting.

DAYLIGHT ADJUSTMENT DIAL ( LUX )

This dial sets the floodlight to be activated at different

light levels. To set the light to activate only after dark, wait

until dusk and turn the dial completely anti-clockwise.

Slowly turn the dial clockwise until the light comes on.

The light will now activate after dusk.

PLEASE NOTE - TO OPERATE UNDER MANUAL OVERRIDE :

When the fitting is installed and operating normally under automatic control from the PIR it can be switched to permanent

operation by simply switching the power off and on again within 3 seconds (the fitting will now be on all the time!).

To change the operation back to automatic control through the PIR simply switch the fitting off again and wait a minimum of

7 seconds. After 7 seconds switch the power back on and the fitting will again be under automatic control through the PIR (the

fitting will only be activated and switched on when movement is detected).

LED PANTHER

FLOODLIGHT FITTING

INSTRUCTIONS

MAINTENANCE

1. Please make sure the power is switched off before starting any

maintenance.

2. In order to maintain good even light coverage, the glass cover

should be cleaned regularly.

3. For good heat dissipation the floodlight housing should also be

cleaned regularly.

4. Please take care when cleaning the glass or floodlight housing.

DO NOT USE water or cleaning solutions, cleaning should

preferably be done with a clean dry cloth.

DEL0585a/Feb_2016/issue_1 page 2 of 2

www.delucelighting.com

PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLATION

LEAVE A COPY FOR THE USER/MAINTENANCE ENGINEER FOR FUTURE REFERENCE

We recommend this ﬁtting is installed by a qualiﬁed Electrician.

GUARANTEE

This product is guaranteed in the EU for a period of 1 year from the date of purchase. The guarantee is invalid in the case of improper use, installation, tampering, removal of the

QC date label, installation in an improper working environment or installation not according to the current edition of the IEE Wiring Regulations (BS 7671). Should this product

fail during the guarantee period it will be replaced free of charge, subject to correct installation and return of the faulty unit. Déluce Lighting does not accept responsibility for any

installation costs associated with the replacement of this product. Your statutory rights are not affected. Déluce Lighting reserves the right to alter speciﬁcations without prior notice.

These instructions are for the Déluce Lighting Panther LED Floodlights :