Show Tec Beacon 360 User manual

Beacon 360 V1
Highlite International B.V. –Vestastraat 2 –6468 EX –Kerkrade –the Netherlands
Ordercode: 45051
MANUAL
ENGLISH

1
Ordercode: 45051
Beacon 360
Table of contents
Warning ...............................................................................................................................................................................2
Unpacking Instructions.................................................................................................................................................2
LED Expected Lifespan ................................................................................................................................................2
Safety Instructions .........................................................................................................................................................2
Operating Determinations ..........................................................................................................................................4
Rigging ............................................................................................................................................................................4
Connection with the mains.........................................................................................................................................5
Return Procedure..........................................................................................................................................................6
Claims..............................................................................................................................................................................6
Description of the device.................................................................................................................................................7
Overview ........................................................................................................................................................................7
Backside .........................................................................................................................................................................8
Installation...........................................................................................................................................................................8
Set Up and Operation .......................................................................................................................................................8
Control Modes...............................................................................................................................................................9
One Beacon (Stand-alone and Manual).............................................................................................................9
One Beacon (Sound-controlled) ...........................................................................................................................9
Multiple Beacons (Master/Slave Mode) ...............................................................................................................9
Multiple Beacons (DMX Control) ..........................................................................................................................10
Fixture Linking...............................................................................................................................................................11
Data Cabling...............................................................................................................................................................11
Control Panel ...............................................................................................................................................................12
Control Mode ..............................................................................................................................................................12
DMX Addressing ..........................................................................................................................................................12
Menu Overview...........................................................................................................................................................13
Main Menu Options....................................................................................................................................................14
1. DMX-512 Mode....................................................................................................................................................14
2. Channel Mode ....................................................................................................................................................14
3. Built-in auto programs ........................................................................................................................................14
4. Manual Control Mode .......................................................................................................................................15
5. Master/Slave Mode ............................................................................................................................................16
6. Sound-controlled Mode ....................................................................................................................................16
7. Pan Reverse Mode .............................................................................................................................................16
8. Tilt Reverse Mode ................................................................................................................................................16
9. Display settings ....................................................................................................................................................16
10. Software version ................................................................................................................................................17
11. Restoration of Factory Settings.......................................................................................................................17
12. Setting Reset ......................................................................................................................................................17
13. Auto Test Mode .................................................................................................................................................17
DMX Channels .............................................................................................................................................................18
9 channels ................................................................................................................................................................18
19 channels ..............................................................................................................................................................19
Maintenance....................................................................................................................................................................21
Replacing the Fuse.....................................................................................................................................................21
Troubleshooting ...............................................................................................................................................................21
No Light.........................................................................................................................................................................21
No Response to DMX..................................................................................................................................................21
Product Specifications....................................................................................................................................................23
Dimensions........................................................................................................................................................................24
Notes ..................................................................................................................................................................................25

2
Ordercode: 45051
Beacon 360
Warning
Unpacking Instructions
Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure
that all parts are present, and have been received in good condition. Notify the dealer immediately and
retain packing material for inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture must be
returned to the factory, it is important that the fixture be returned in the original factory box and packing.
Your shipment includes:
• Showtec Beacon 360
• 1 mounting bracket
• Powercon cable 1,5 m
• 2 mounting screws
• User manual
LED Expected Lifespan
LEDs gradually decline in brightness over time. HEAT is the dominant factor that leads to the acceleration
of this decline. Packaged in clusters, LEDs exhibit higher operating temperatures than in ideal or singular
optimum conditions. For this reason, when all color LEDs are used at their fullest intensity, life of the LEDs is
significantly reduced. If improving the lifespan is of higher priority, place care in providing for lower
operational temperatures. This may include climatic-environmental and the reduction of overall
projection intensity.
Safety Instructions
Every person involved with the installation, operation and maintenance of this device has to:
•be qualified
•follow the instructions of this manual
Before the initial start-up, please make sure that there is no damage caused by transportation.
Should there be any, consult your dealer and do not use the device.
To maintain perfect condition and to ensure a safe operation, it is absolutely necessary for the user to
follow the safety instructions and warning notes contained in this manual.
Please consider that damages caused by manual modifications to the device are not subject to
warranty.

3
Ordercode: 45051
Beacon 360
This device contains no user-serviceable parts. Refer to qualified technicians only.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance of
this manual or any unauthorized modification to the device.
•Never let the power cord come into contact with other cables! Handle the power cord and all
connections with the mains with particular caution!
•Never remove warning or informative labels from the unit.
•Never use anything to cover the ground contact.
•Never lift the fixture holding it by the projector-head, as the mechanics may be damaged.
Always hold the fixture by the transport handles.
•Never place any material over the lens.
•Never look directly into the light source.
•Never leave any cables lying around.
•Never loosen the screws of the gobo, otherwise you risk opening of the ball bearing.
•Do not insert objects into air vents.
•Do not connect this device to a dimmerpack.
•Do not switch the device on and off in short intervals, as this will reduce the device’s life.
•Do not touch the device’s housing bare-handed during its operation (housing becomes very hot).
Allow the fixture to cool for at least 5 minutes before handling.
•Do not shake the device. Avoid brute force when installing or operating the device.
•Only use the device indoors, avoid contact with water or other liquids.
•Only operate the fixture after having checked if the housing is firmly closed and all screws are tightly
fastened.
•Only operate the device after having familiarized with its functions.
•Avoid flames and do not put close to flammable liquids or gases.
•Always keep the case closed while operating.
•Always allow a free air space of at least 50 cm around the unit for ventilation.
•Always disconnect power from the mains, when device is not used or before cleaning! Only handle
the power cord holding it by the plug. Never pull out the plug by tugging the power cord.
•Make sure that the device is not exposed to extreme heat, moisture or dust.
•Make sure that the available voltage is not higher than stated on the rear panel.
•Make sure that the power cord is never crimped or damaged. Check the device and the power
cord from time to time.
•If the lens is obviously damaged, it has to be replaced.
•If device was dropped or struck, disconnect mains power supply immediately. Have a qualified
engineer inspect for safety before operating.
•If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not
switch it on immediately. The arising condensation water might damage your device.
Leave the device switched off until it has reached room temperature.
•If your Showtec device fails to work properly, discontinue the use immediately. Pack the unit securely
(preferably in the original packing material), and return it to your Showtec dealer for service.
•For adult use only. The moving head must be installed beyond the reach of children. Never leave the
unit running unattended.
•Never attempt to bypass the thermostatic switch or fuses.
•For replacement use fuses of same type and rating only.
•The user is responsible for correct positioning and operating of the Beacon. The manufacturer will not
accept liability for damages caused by the misuse or incorrect installation of this device.
•This device falls under protection class I. Therefore it is essential to connect the yellow/green
conductor to earth.
•During the initial start-up some smoke or smell may arise. This is a normal process and does not
necessarily mean that the device is defective.
•Repairs, servicing and electric connection must be carried out by a qualified technician.
•WARRANTY: Till one year after date of purchase.

4
Ordercode: 45051
Beacon 360
Operating Determinations
•This device is not designed for permanent operation. Consistent operation breaks will ensure that the
device will serve you for a long time without defects.
•The minimum distance between light output and the illuminated surface must be bigger than 1
meter.
•The maximum ambient temperature ta= 40°C must never be exceeded.
•The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
•If this device is operated in any other way than the one described in this manual, the product may
suffer damages and the warranty becomes void.
•Any other operation may lead to dangers like short-circuit, burns, electric shock, crash, etc.
You endanger your own safety and the safety of others!
Rigging
Please follow the European and national guidelines concerning rigging, trussing and all other safety
issues.
Do not attempt the installation yourself !
Always let the installation be carried out by an authorized dealer!
Procedure:
•If the projector is lowered from the ceiling or high joists, professional trussing systems have to be used.
•Use a clamp to mount the projector, with the mounting bracket, to the trussing system.
•The projector must never be fixed swinging freely in the room.
•The installation must always be secured with a safety attachment, e.g. an appropriate safety net or
safety cable.
•When rigging, de-rigging or servicing the projector, always make sure, that the area below the
installation site is secured and that there are not any unauthorized people around.
The Beacon can be placed on a flat stage floor or mounted to any kind of truss with a clamp.

5
Ordercode: 45051
Beacon 360
Mounting a clamp to the underside of the Beacon 360 moving head
Improper installation can cause serious injuries to people and/or damage of property !
Connection with the mains
Connect the device to the mains with the power plug.
Always check if the right color cable is connected to the right place.
International
EU Cable
UK Cable
US Cable
Pin
L
BROWN
RED
YELLOW/COPPER
PHASE
N
BLUE
BLACK
SILVER
NEUTRAL
YELLOW/GREEN
GREEN
GREEN
PROTECTIVE GROUND
Make sure that the device is always properly connected to the earth!
Improper installation can cause serious injuries to people and/or damage of property!

6
Ordercode: 45051
Beacon 360
Return Procedure
Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Package must be clearly labeled with a Return Authorization Number (RMA number). Products returned
without an RMA number will be refused. Highlite will not accept the returned goods or any responsibility.
Call Highlite 0031-455667723 or mail aftersal[email protected] and request an RMA prior to shipping the fixture.
Be prepared to provide the model number, serial number and a brief description of the cause for the
return. Be sure to properly pack fixture, any shipping damage resulting from inadequate packaging is the
customer’s responsibility. Highlite reserves the right to use its own discretion to repair or replace
product(s). As a suggestion, proper UPS packing or double-boxing is always a safe method to use.
Note: If you are given an RMA number, please include the following information on a piece of paper
inside the box:
01) Your name
02) Your address
03) Your phone number
04) A brief description of the symptoms
Claims
The client has the obligation to check the delivered goods immediately upon delivery for any short-
comings and/or visible defects, or perform this check after our announcement that the goods are at their
disposal. Damage incurred in shipping is the responsibility of the shipper; therefore the damage must be
reported to the carrier upon receipt of merchandise.
It is the customer's responsibility to notify and submit claims with the shipper in the event that a fixture is
damaged due to shipping. Transportation damage has to be reported to us within one day after receipt
of the delivery.
Any return shipment has to be made post-paid at all times. Return shipments must be accompanied with
a letter defining the reason for return shipment. Non-prepaid return shipments will be refused, unless
otherwise agreed in writing.
Complaints against us must be made known in writing or by fax within 10 working days after receipt of the
invoice. After this period complaints will not be handled anymore.
Complaints will only then be considered if the client has so far complied with all parts of the agreement,
regardless of the agreement of which the obligation is resulting.

7
Ordercode: 45051
Beacon 360
Description of the device
Features
The Showtec Beacon 360 is a moving head fixture with high output and great effects.
•Beam Angle: 8°
•Power consumption: 60 W
•LCD display
•9, 19 Channels
•360° pan and 360° tilt
•Colors: Red, Green, Blue, White
•Control modes: DMX-512, Auto, Manual, Master/Slave, Sound
•Metal & Flame-retardant plastic housing
•DMX Data IN/OUT
•Powercon IN/OUT
•Dimmer: 0-100%
• Strobe: 0-20Hz
• Fuse: 3A/250V
• Control protocol: DMX-512
• Dimensions: 241 mm x 145 mm x 313 mm (LxWxH)
• Weight: 5 kg
Overview
Fig. 01
01) LCD Display +control buttons
02) Lens 2
03) Lens 1

8
Ordercode: 45051
Beacon 360
Backside
Fig. 02
04) Powercon connector IN
05) Powercon connector OUT
06) 3-pin DMX signal connector IN
07) 3-pin DMX signal connector OUT
08) Ground/earth connection
09) Power switch ON/OFF
10) Fuse 3A/250V
Installation
Remove all packing materials from the Beacon 360. Check that all foam and plastic padding is removed.
Connect all cables.
Do not supply power before the whole system is set up and connected properly.
Always disconnect from electric mains power supply before cleaning or servicing.
Damages caused by non-observance are not subject to warranty.
Set Up and Operation
Follow the directions below, as they pertain to your preferred operation mode.
Before plugging the unit in, always make sure that the power supply matches the product specification
voltage. Do not attempt to operate a 120V specification product on 230V power, or vice versa.

9
Ordercode: 45051
Beacon 360
Control Modes
There are 5 modes:
Built-in programs (stand-alone)
Manual mode Built-in programs (stand-alone)
Sound-controlled
Master/Slave
DMX-512 (9CH, 19CH)
One Beacon (Stand-alone and Manual)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains Powercon cord into a proper electric power supply socket.
04) When the Beacon is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see page 14 for more information about the Built-in auto programs and page 15 for more
information about the Manual mode.
One Beacon (Sound-controlled)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains Powercon cord into a proper electric power supply socket.
04) When the Beacon is not connected with a DMX cable, it functions as a stand-alone device.
05) Please see page 16 for more information about the Sound-controlled mode.
Multiple Beacons (Master/Slave Mode)
01) Fasten the effect light onto firm trussing. Leave at least 0,5 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains Powercon cord into a proper electric power supply socket.
04) Use a 3-pin XLR cable to connect the Beacons.
The pins:
01) Earth
02) Signal (-)
03) Signal (+)
05) Link the units as shown in Fig. 03, connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units. You can
use the same functions on the master device as described on pages 14 and 16 (Built-in or Sound-
controlled). This means on the master device you can set your desired operation mode and all slave
devices will react the same as the master device.
Multiple Beacons Master/Slave Set Up
Fig. 03

10
Ordercode: 45051
Beacon 360
Multiple Beacons (DMX Control)
01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation.
02) Always use a safety cable (ordercode 70140 / 70141).
03) Plug the end of the electric mains power cord into a proper electric power supply socket.
04) Use a 3-p XLR cable to connect the Beacons and other devices.
05) Link the units as shown in Fig. 04, Connect a DMX signal cable from the first unit's DMX "out" socket to
the second unit's "in" socket. Repeat this process to link the second, third, and fourth units.
06) Supply electric power: Plug electric mains power cords into each unit's IEC socket, then plug the
other end of the mains power cord into proper electric power supply sockets, starting with the first
unit. Do not supply power before the whole system is set up and connected properly.
Multiple Beacons DMX Set Up
Fig. 04

11
Ordercode: 45051
Beacon 360
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to
run synchronized shows of two or more fixtures set to a master/slave operating mode. The combined
number of channels required by all the fixtures on a serial data link determines the number of fixtures the
data link can support.
Important:
Fixtures on a serial data link must be daisy-chained in a single line. To comply with the
EIA-485 standard, no more than 30 devices should be connected on one data link.
Connecting more than 30 fixtures on one serial data link without the use of a DMX optically
isolated splitter may result in deterioration of the digital DMX signal.
Maximum recommended DMX data link distance: 100 meters
Maximum recommended number of fixtures on a DMX data link: 30 fixtures
Data Cabling
To link fixtures together, you must obtain data cables. You can purchase DAP Audio certified DMX cables
directly from a dealer/distributor or construct your own cable. If you choose to create your own cable,
please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic
interference.
DAP Audio Certified DMX Data Cables
•DAP Audio Basic microphone cable for allround use. bal. XLR/M 3 p. > XLR/F 3 p.
Ordercode FL01150 (1,5m.), FL013 (3m.), FL016 (6m.), FL0110 (10m.), FL0115 (15m.), FL0120 (20m.).
•DAP Audio cable for the demanding user with exceptional audio-qualities and connector made by
Neutrik®. Ordercode FL71150 (1,5m.), FL713 (3m.), FL716 (6m.), FL7110 (10m).

12
Ordercode: 45051
Beacon 360
Control Panel
A) LCD display
B) ESC button
C) SETUP button
D) UP button
E) DOWN button
Fig. 05
Control Mode
The fixtures are individually addressed on a data-link and connected to the controller.
The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it,
the controller will display the saved DMX address the next time.)
DMX Addressing
The control panel on the front side of the base allows you to assign the DMX fixture address, which is the
first channel from which the Beacon will respond to the controller.
Please note when you use the controller, the unit has 19 channels.
When using multiple Beacons, make sure you set the DMX addresses right.
Therefore, the DMX address of the first Beacon should be 1(001); the DMX address of the second Beacon
should be 1+19=20 (020); the DMX address of the third Beacon should be 20+19=39 (039), etc.
Please, make sure that you do not have any overlapping channels in order to control each Beacon
correctly.
If two or more Beacons are addressed similarly, they will work similarly.
Controlling:
After having addressed all Beacon fixtures, you may now start operating these via your lighting controller.
Note: After switching on, the Beacon will automatically detect whether DMX-512 data is received or not.
If there is no data received at the DMX-input, the “LED“ on the control panel will not flash.
The problem may be:
•The XLR cable from the controller is not connected with the input of the Beacon.
•The controller is switched off or defective, the cable or connector is detective, or the signal wires are
swapped in the input connector.
Note: It is necessary to insert an XLR termination plug (with 120 Ohm) in the last fixture in order to ensure
proper transmission on the DMX data link.

13
Ordercode: 45051
Beacon 360
Menu Overview

14
Ordercode: 45051
Beacon 360
Main Menu Options
DMX-512 Mode
Channel Mode (9CH, 19CH)
Show Mode
Manual Control mode
Master/Slave Mode
Sound-controlled Mode
Pan Reverse Mode
Tilt Reverse Mode
Display settings
Software Version
Restoration of Factory Settings
Setting Reset
Auto Test Mode
1. DMX-512 Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to set the DMX address between .
04) Press the SETUP button to confirm the address.
2. Channel Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to choose between 2 options: .
04) Press the SETUP button to confirm your choice.
3. Built-in auto programs
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to choose between 2 options: .
04) Press the SETUP button to confirm your choice.

15
Ordercode: 45051
Beacon 360
4. Manual Control Mode
In this menu it is possible to manually adjust the device’s settings.
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to toggle between the following settings:
Pan
Tilt
Red Color
Green Color
Blue Color
White Color
04) When the display shows , press the SETUP button to enter the menu.
Subsequently, press the UP and DOWN buttons to adjust the pan movement settings between
. The values correspond with their DMX counterparts.
05) Press the SETUP button to store the changes.
06) When the display shows , press the SETUP button to enter the menu.
Subsequently, press the UP and DOWN buttons to adjust the tilt movement settings between
. The values correspond with their DMX counterparts.
07) Press the SETUP button to store changes.
08) When the display shows , press the SETUP button to enter the menu.
09) Press the UP and DOWN buttons to set the red color intensity between .
0 = off, 255 = full on.
10) Press the SETUP button to store changes.
11) When the display shows , press the SETUP button to enter the menu.
12) Press the UP and DOWN buttons to set the green color intensity between .
0 = off, 255 = full on.
13) Press the SETUP button to store changes.
14) When the display shows , press the SETUP button to enter the menu.
15) Press the UP and DOWN buttons to set the blue color intensity between .
0 = off, 255 = full on.
16) Press the SETUP button to store changes.
17) When the display shows , press the SETUP button to enter the menu.
18) Press the UP and DOWN buttons to set the white color intensity between .
0 = off, 255 = full on.
19) Press the SETUP button to store changes.

16
Ordercode: 45051
Beacon 360
5. Master/Slave Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to toggle between the following slave modes:
Normal slave mode
Mirror slave mode
04) Press the SETUP button to confirm your choice.
6. Sound-controlled Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to toggle between the following options:
Sound-controlled mode ON
Sound-controlled mode OFF
Sound Sensitivity settings
04) Press the SETUP button to confirm your choice.
05) When the display shows , press the SETUP button to enter the sound sensitivity menu.
06) Press the UP and DOWN buttons to set the sound sensitivity between .
0 = Off, 255 = very sensitive.
07) Press the SETUP button to store changes.
7. Pan Reverse Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to choose between 2 options: .
04) Press the SETUP button to store changes.
8. Tilt Reverse Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to choose between 2 options: .
04) Press the SETUP button to store changes.
9. Display settings
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to toggle between the following options:
Display always ON
Display OFF after 10 seconds
Display brightness
04) Press the SETUP button to confirm your choice.

17
Ordercode: 45051
Beacon 360
05) When the display shows , press the SETUP button to enter the display brightness menu.
06) Press the UP and DOWN buttons to set the display brightness between .
01 = dark, 10 = very bright.
07) Press the SETUP button to store changes.
10. Software version
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to look up the currently installed software version.
11. Restoration of Factory Settings
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to choose between 2 options: .
04) If the display shows , press the SETUP button to start restoring the factory settings.
12. Setting Reset
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to enter the menu.
03) Press the UP and DOWN buttons to choose between 2 options: .
04) If the display shows , press the SETUP button to start resetting settings.
13. Auto Test Mode
01) While in the main menu, press the UP and DOWN buttons until the display shows .
02) Press the SETUP button to run the automatic test of all the available features.

18
Ordercode: 45051
Beacon 360
DMX Channels
9 channels
Channel 1 –Horizontal movement (Pan)
0-127
Manual pan adjustment, between 0-360°
128-191
Clockwise rotation, from fast to slow
192-255
Counterclockwise rotation, from slow to fast
Channel 2 –Vertical movement (Tilt)
0-127
Manual tilt adjustment, between 0-360°
128-191
Clockwise rotation, from fast to slow
192-255
Counterclockwise rotation, from slow to fast
Channel 3 –Dimmer
0-255
Dimmer intensity, from OFF to full ON
Channel 4 –Red color
0-255
Red color intensity, from OFF to full ON
Channel 5 –Green color
0-255
Green color intensity, from OFF to full ON
Channel 6 –Blue color
0-255
Blue color intensity, from OFF to full ON
Channel 7 –White color
0-255
White color intensity, from OFF to full ON
Channel 8 –Strobe effect
0-5
Strobe OFF
6-255
Strobe speed, from slow to fast
Channel 9 –Setting reset
0-9
Not functional
10-20
Setting reset active
21-255
Not functional

19
Ordercode: 45051
Beacon 360
19 channels
Channel 1 –Manual horizontal movement (Pan)
0-255
Manual pan adjustment, between 0-360°
Channel 2 –Pan 16-bit
0-255
Manual 16-bit pan adjustment
Channel 3 –Manual vertical movement (Tilt)
0-255
Manual tilt adjustment, between 0-360°
Channel 4 –Tilt 16-bit
0-255
Manual 16-bit tilt adjustment
Channel 5 –Pan and Tilt speed
0-255
Speed adjustment, from fast to slow
Channel 6 –Horizontal movement (Pan)
0-127
Manual pan adjustment, between 0-360°
128-191
Clockwise rotation, from fast to slow
192-255
Counterclockwise rotation, from slow to fast
Channel 7 –Vertical movement (Tilt)
0-127
Manual tilt adjustment, between 0-360°
128-191
Clockwise rotation, from fast to slow
192-255
Counterclockwise rotation, from slow to fast
Channel 8 –Red color, LED 1
0-255
Red color intensity, from OFF to full ON
Channel 9 –Green color, LED 1
0-255
Green color intensity, from OFF to full ON
Channel 10 –Blue color, LED 1
0-255
Blue color intensity, from OFF to full ON
Channel 11 –White color, LED 1
0-255
White color intensity, from OFF to full ON
Channel 12 –Red color, LED 2
0-255
Red color intensity, from OFF to full ON
Channel 13 –Green color, LED 2
0-255
Green color intensity, from OFF to full ON
Channel 14 –Blue color, LED 2
0-255
Blue color intensity, from OFF to full ON
Channel 15 –White color, LED 2
0-255
White color intensity, from OFF to full ON
Channel 16 –Strobe effect
0-5
Strobe OFF
6-255
Strobe speed, from slow to fast