Denon DCD-F107 User manual

D&M Holdings Inc.
SERVICE MANUAL
e
e
Copyright 2010 D&M Holdings Inc. All rights reserved.
WARNING: Violators will be prosecuted to the maximum extent possible.
MODEL JP E3 E2 EK K2A E1C E1K EUT
DCD-F107
P
COMPACT DISC PLAYER
Ver. 4
•Some illustrations using in this service manual are slightly different from the actual set.
•Please use this service manual with referring to the operating instructions without fail.
•For purposes of improvement, specications and design are subject to change without notice.
S0164-1V04DM/DG1010
Please refer to the
MODIFICATION NOTICE.

2
DCD-F107
Please heed the points listed below during servicing and inspection.
◎Heed the cautions!
Spots requiring particular attention when servicing, such
as the cabinet, parts, chassis, etc., have cautions indicated
on labels or seals. Be sure to heed these cautions and the
cautions indicated in the handling instructions.
◎Caution concerning electric shock!
(1) An AC voltage is impressed on this set, so touching in-
ternal metal parts when the set is energized could
cause electric shock. Take care to avoid electric shock,
by for example using an isolating transformer and
gloves when servicing while the set is energized, un-
plugging the power cord when replacing parts, etc.
(2)There are high voltage parts inside. Handle with extra
care when the set is energized.
◎Caution concerning disassembly and
assembly!
Though great care is taken when manufacturing parts from
sheet metal, there may in some rare cases be burrs on the
edges of parts which could cause injury if fingers are
moved across them. Use gloves to protect your hands.
◎Only use designated parts!
The set's parts have specific safety properties (fire resis-
tance, voltage resistance, etc.). For replacement parts, be
sure to use parts which have the same properties. In par-
ticular, for the important safety parts that are marked zon
wiring diagrams and parts lists, be sure to use the desig-
nated parts.
◎Be sure to mount parts and arrange
the wires as they were originally!
For safety reasons, some parts use tape, tubes or other in-
sulating materials, and some parts are mounted away from
the surface of printed circuit boards. Care is also taken with
the positions of the wires inside and clamps are used to
keep wires away from heating and high voltage parts, so
be sure to set everything back as it was originally.
◎Inspect for safety after servicing!
Check that all screws, parts and wires removed or discon-
nected for servicing have been put back in their original po-
sitions, inspect that no parts around the area that has been
serviced have been negatively affected, conduct an insu-
lation check on the external metal connectors and between
the blades of the power plug, and otherwise check that
safety is ensured.
(Insulation check procedure)
Unplug the power cord from the power outlet, disconnect
the antenna, plugs, etc., and turn the power switch on. Us-
ing a 500V insulation resistance tester, check that the in-
sulation resistance between the terminals of the power
plug and the externally exposed metal parts (antenna ter-
minal, headphones terminal, microphone terminal, input
terminal, etc.) is 1MΩor greater. If it is less, the set must
be inspected and repaired.
Concerning important safety
parts
Many of the electric and structural parts used in the set
have special safety properties. In most cases these prop-
erties are difficult to distinguish by sight, and using re-
placement parts with higher ratings (rated power and
withstand voltage) does not necessarily guarantee that
safety performance will be preserved. Parts with safety
properties are indicated as shown below on the wiring dia-
grams and parts lists is this service manual. Be sure to re-
place them with parts with the designated part number.
(1) Schematic diagrams ... Indicated by the zmark.
(2) Parts lists ... Indicated by the zmark.
Using parts other than the designated
parts could result in electric shock, fires or
other dangerous situations.
SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
LEAKAGE CURRENT CHECK
Before returning the unit to the customer, make sure you make either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the unit is defective.
LASER RADIATION
Do not stare into beam or view directly with optical instruments, class 3A laser product.
CAUTION
CAUTION

3
DCD-F107
DIMENSION

4
DCD-F107
WIRE ARRANGEMENT
If wire bundles are untied or moved to perform adjustment or parts replacement etc.,be sure to rearrange them neatly as
they were originally bundled or placed afterward.
Otherwise, incorrect arrangement can be a cause of noise generation.
Wire arrangement viewed from the top
Front Panel side
Back Panel side

5
DCD-F107
DISASSEMBLY
• Disassemble in order of the arrow of the figure of following flow.
• In the case of the re-assembling, assemble it in order of the reverse of the following flow.
• In the case of the re-assembling, observe "attention of assembling" it.
About the photos used for descriptions in the “DISASSEMBLY” section.
• The direction from which the photographs used herein were photographed is indicated at "Direction of photograph: ***" at
the left of the respective photographs.
• Refer to the table below for a description of the direction in which the photos were taken.
• Photographs for which no direction is indicated were taken from above the product.
TOP COVER
LENAPRAERSNARTREWOPROOD
Refer to "DISASSEMBLY 1.DOOR" Refer to "EXPLODED VIEW" Refer to "EXPLODED VIEW"
Refer to "EXPLODED VIEW" LENAPRAERSNARTREWOP
)01M:WEIVDEDOLPXEfo.oN.feR()3C:WEIVDEDOLPXEfo.oN.feR(ROOD
(Ref. No. of EXPLODED VIEW : P1)
AUDIO PCB
FRONT PANEL ASSY Refer to "EXPLODED VIEW"
Refer to "DISASSEMBLY 2.FRONT PANEL ASSY" INPUT PCB
Refer to "EXPLODED VIEW" (Ref. No. of EXPLODED VIEW : C7)
FRONT PCB
(Ref. No. of EXPLODED VIEW : C1) POWER PCB
㩷Refer to "EXPLODED VIEW"
MECHANISM POWER PCB
Refer to "DISASSEMBLY
㩷(Ref. No. of EXPLODED VIEW : C6)
3.MECHANISM"
Refer to "EXPLODED VIEW"
CD MECHANISM ASSY
(Ref. No. of EXPLODED VIEW : C5)
CD MAIN PCB
Refer to "EXPLODED VIEW"
CD MAIN PCB
(Ref. No. of EXPLODED VIEW : C4)
The viewpoint of each photograph
(photography direction)
［View from above］
Front side
Direction of photograph: A

6
DCD-F107
1. DOOR
(1) Take off the Chucking plate after removing screws.
(2) Open the CD tray by turning the Drive gear clockwise.
(3) Detach the DOOR.
TOP COVER DOOR
→
Proceeding :
Chucking plate
Drive gear
CD tray
DOOR

7
DCD-F107
2. FRONT PANEL ASSY
(1) Remove the screws.
(2) Cut the clamp bands, disconnect the connector wires and FFC Cable.
TOP COVER DOOR
→FRONT PANEL ASSY →
Proceeding :
View from bottom
CN97
cut
FFC Cable
CN52
cut
Please refer to "EXPLODED VIEW" for the disassembly method of each PCB included in FRONT PANEL ASSY.

8
DCD-F107
3. CD MECHANISM ASSY
(1) Cut the clamp bands, disconnect the connector wires. Remove the screws.
(2) Disconnect the connector wires.
(3) Laser short-circuit in Pick-up of CD MECHANISM, then disconnect the FFC Cable.
Proceeding : CD MECHANISM ASSY
→
TOP COVER DOOR
→FRONT PANEL ASSY →
ً ً
Direction of photograph: A
Connector wires
Soldering place
Direction of photograph: A
FFC Cable
Laser short-circuit

9
DCD-F107
DISASSEMBLY OF MECHANIC
(Follow the procedure below in reverse order when reassembling.)
Caution : The optical pickup can damaged by sassily by static electricity charged on human body. Take necessary anti-static
measures when repairing around the optical pickup.
1. Chucking plate
(1) Remove 2 top screws, then detach the Chucking plate.
(2) Detaching the Chucking pulley and chucking yoke by removing the 3 hooks, when abandoning CD MECHA ass’y.
2. CD tray
When abandoning CD MECHA ass’y, please detach the CD tray.
(1) Detach the Sw pin on the CD tray.
(2) Open the CD tray by turning the Drive gear clockwise.
(3) Open the Stopper as shown in the fig., then detach CD tray.
Chucking yoke
Chucking plate
Chucking pulley
Screws
Mugnet
Stopper
Stopper
Sw pin
CD tray
Drive gear


10
DCD-F107
Note Handling and Replacement of the Laser pick-up
1. Protection of the LD
Short a part of the LD circuit by soldering. After connection to a circuit, remove the short solder.
2. Precautions when handling the laser CD mechanism
• Handle the laser pick-up so that it is not exposed to dust.
• Do not leave the laser pick-up bare. Be sure to cover it.
• If dust adheres on lens of the pick-up, blow it off with a blower brush.
• Do not shock the laser pick-up.
• Do not watch the light of the laser pick-up.
3. Cautions on assembling and adjustment
• Be sure that to the bench, jig, head of soldering iron (with ceramic) and measuring instruments are well grounded.
• Workers who handle the laser pick-up must be grounded.
• The finished mechanism (prior to anchoring in the set) should be protected against static electricity and dust. The mecha-
nism must be stored that damaging outside forces are not received.
• When carrying the finished mechanism, hold it by the
chassis body
• For proper operation, storage and operating environment should not contain corrosive gases. For example H2S, SO2, NO2,
CI2etc. In addition storage environment should not have materials that emit corrosive gases especially from silicic, cyanic,
formalin and phenol group. I the mechanism or the set, existence of corrosive gases may cause no rotation in motor.
4. Determining whether the laser pick-up is defective
• Measure the waveform at RFO-VC on "MCU PCB Unit ".
( For measuring points and waveforms, see pages 26, 27.)
• The laser pick-up is OK if the amplitude level of the measured RFO waveform is between 0.4 and 1.1 Vp-p, defective oth-
erwise.
Protective soldering place for laser diode.

11
DCD-F107
Diagnostics of optical pickup and replacing traverse unit d
Make failure diagnostics of the Optical Pickup as follows.
If the laser drive current (Iop) becomes more than 1.5 times of the initial value, the Optical Pickup should be replaced.
The laser drive current initial value is checked by "Iop checked Method" of next page.
In case of replacing the Pickup, change the whole part of the Traverse Unit.
No mechanical adjustment is necessary after the replacement.
Laser drive current initial value:
･13 flashing
XXX : Initial value : Stored data (EEPROM stored value)
YYY : Current value
S/C: XXXmA/YYYmA
LASER CURRENT
Disc no read, unsteady playback, etc.
Laser drive current (Iop) check
Present value exceeds the initial value by 1.5 times
Traverse Unit replacing
Laser current (Iop) memorizing after replacement

12
DCD-F107
SPECIAL MODE
No Key name Function Display
1Service mode
• AC is turned on while pressing the 5and 2button
same time on DCD-F107.(Model name display)
1.1
Version No. of
main μ-com
Display mode
• Press the 9button.
"****" : Version number of main μ-com
1.2
Version No. of
USB μ-com
Display mode
• Press the 9button while version No. of main
μ-com is displayed.
"****" : Version number of USB μ-com
1.3 FLD check mode
• When display is version No. of USB μ-com and
the 9button is pressed, turn on the entire dis-
play is flashing with an interval of about 1 second.
• Press the 9button again in the turn on each
grid of FLD. (Each grid is displayed at interval of 1
second.)
2 CD test mode
• AC is turned on while pressing the 5and 2button
same time on DCD-F107.(Entering the Service
mode)
• Press the 2and /
13 button same time while
version display, FLD check mode and heat run-
mode.(CD TEST MODE display)
• Press the DISC/USB button continuously for over
3 seconds to display the version number of main
μ-com.
13 flashing
2.1 Disc loading
• Press the 5button to open the tray.
• Set a disc on the tray, then press the 5button
again to close the tray.
2.2 Servo check
• Press the /
13 button. Execute the following
steps.
qLD ON (with servo still stopped)
wFOCUS ON (disc rotation, tracking off)
If no disc loaded, retry then stop.
eCLV ON
・13 flashing
q
w
e
DCD-F107
Ver xxxx
USB_Ver ****
00 CD TEST MODE
01 LD ON
02 Focus ON
03 CLV ON

13
DCD-F107
2.2 Servo check
rTRACKING ON
tSUB CODE readout (playback sound output)
• The BER (Block Error Rate) generated in 1
second's time is displayed on the upper tier of
the display.
• The playback position (IN/MID/OUT) can be
changed by pressing the 8or 9button.
• The count of the errors that could not be
corrected with the C1 error correction system is
displayed.
yWhen display is as in tand the / 13button is
pressed, conduct BER (Block Error Rate)
display for 2 seconds.
• The BER (Block Error Rate) generated in 10
second's time is displayed of the display.
bPress /
13 button continuously for over 1
second to switch directly to SUB CODE readout
in step t.
r
t
[IN]
[MID]
[OUT]
###### : B.E.R., @@ : T.No, XX:XX : Time
y
PPP : Playback position (IN/MID/OUT)
###### : 1
second's B.E.R. , *****: 10 second's B.E.R.
2.3 Pickup
movement
・In the stop mode, pickup moves in REV (inwards)
or FWD (outwards) direction when 8or 9
button pressed.
・When 8button pressed, move to stop
operation after detection that inner switch has
turned on.
・Pickup movement stops when button released.
(Pickup moves while button is pressed.)
Continuous display of previous time
2.4 Stop
・When 2button is pressed, play operation and
servo stop.
・After stopping, conduct reading of auto adjust
values.
・13 flashing
2.5 All servo on
・When 2 and 5 button is pressed, all servos turn
on, auto adjustment is performed and switch to
playback operation. (Playback sound output)
(NOTE)When the 2button is pressed for over 1
second while the laser turns on and the laser
current is measured.
・13 flashing
@@ : T.No, XX:XX : Time
No Key name Function Display
04 Tracking ON
INERR######
05 @@
Tr XX:XX
MID ERR ######
05 @@
Tr XX:XX
OUT ERR ######
05 @@
Tr XX:XX
PPP ERR ######
ERR ******
00 CD TEST MODE
@@ Tr XX:XX

14
DCD-F107
2.6 Laser current is
display
・When the 2button is pressed for over 1 second
while the DCD-F107 is in the stop mode, the
laser turns on and the laser current is measured.
・The laser drive current undergoes A/D
conversion for calculation. Decimal values are
discarded.
・The first current value is measured 3 seconds
after the laser turns on.
・The current value is updated every 3 seconds.
・Press the 2button, CD test mode display (2)
reappears.
・Stored data is not cleared, even when the DCD-
F107 is reset.
qOverwriting the stored data
・When the / 13button is pressed for over 5
seconds while the laser current is displayed, the
current value is stored in the EEPROM
(overwriting the stored data).
・Once rewriting is completed, the display in 2.6
reappears.
・Rewriting is performed upon shipment from the
factory and when the mechanism is replaced.
･13 flashing
XX : Stored data : EEPROM Stored value
YY : Current value
q
2.7 Adjustment value
display
・Press the 2button after executing the servo auto
adjustment.
・When 9button is pressed, the adjustment
values are displayed in the following order.
qFOCUS BALANCE
wFOCUS GAIN
eTRACKING BALANCE
rTRACKING GAIN
tFOCUS OFFSET
yTRACKING OFFSET
・13 flashing
q
XX : Adjustment value
w
XX : Adjustment value
e
XX : Adjustment value
r
XX : Adjustment value
t
XX : Adjustment value
y
XX : Adjustment value
No Key name Function Display
S/C: XXXmA/YYYmA
LASER CURRENT
STORED
LASER CURRENT
XX
FOCUS BALANCE
XX
FOCUS GAIN
XX
TRACKING BALANCE
XX
TRACKING GAIN
XX
FOCUS OFFSET
XX
TRACKING OFFSET

15
DCD-F107
2.7 Adjustment value
display
uRFRP
iReturn to q.
(Note)If auto adjustment is not completed, proper
values are not displayed.
u
XX : Adjustment value
2.8
Accumulated
laser on time
display
・When the DISC/USB and 5 button is pressed
while the DCD-F107 is in the stop mode, the
accumulated laser on time is displayed.
・The laser drive times are added and the result is
displayed.
・One count corresponds to 10 minutes. (Values
under 10 minutes are discarded.)
・Count values are stored in the EEPROM every 10
minutes.
・The accumulated laser on time is displayed in
hours.
・Laser ON/OFF is monitored and counted.
・Press the 2button, CD test mode display (2)
reappears.
・The count values are not cleared, even when the
set is reset.
・Minimum display specification
• No. digits stored in EPROM: 4, 0xFFFF
• No. digits displayed: 5
• When the time exceeds 10922 hours, the
stored data is not updated and the value is
fixed to 0xFFFF.
(The display is fixed to 10922 hours.)
qCount value is reset
・When the / 13button is pressed for over 5
seconds while the accumulated laser on time is
displayed, the count value is reset.
・After resetting is completed, the display in 2.6
(00000 hours on the top line) reappears.
・Count value is reset upon shipment from the
factory and when the mechanism is replaced.
・13 flashing
q
3CD heat run
mode
・AC is turned on while pressing the 5and 2button
same time on DCD-F107.
・Switches to mode according to button input.
・Press the reverse button to switch the mode while
displaying the version of the main μcom.
(Normal heat run mode, Heat run short mode,
Automatic mounting mode.) d
・If an error occurs, display the error and stop
operation at that point.
・Number of operations held.
・While heat run, the operation of each button is not
valid except the ON/STANDBY button and
pressing the 5and 2button same time.
No Key name Function Display
XX
RFRP
XXXXX hour
LASER ON TIME
CLEAR
LASER ON TIME

16
DCD-F107
3.1 Normal heat run
mode
・Press the /
13button while name of the model is
displayed or H.R.NORMAL is displayed.
・Count this as the 0th heat run repetition.
qPlay from the first to last track on disc.
wAfter disc playback has finished, move pickup
to innermost position and open tray.
eWhen loader open status detected, close tray
again, re-read TOC and start playback from the
first track on the disc.
rThe heat run repetition no. is incremented
(increased by 1) when the tray is opened.
※If the 2and 5button is pressed while operat-
ing, number of heat run is displayed for 3 sec-
onds.
tConduct qto erepeatedly.
・Model Name display
・H.R.NORMAL display
・Normal heat run mode
Normal display except when 1light, 3flashing
qNormal display except when 1light, 3flashing
w
XXXX : No. of heat run repetitions
eNormal display except when 1light, 3flashing
r
XXXX : No. of heat run repetitions
3.2 Heat run Short
mode
・Press the /
13 button while name of the
H.R.SHORT is displayed.
・Count this as the 0th heat run repetition.
qPlay the last track only on disc.
wAfter disc playback has finished, move pickup
to innermost position and open tray.
eWhen loader open status detected, close tray
again, re-read TOC and start playback from the
first track on the disc.
rThe heat run repetition no. is incremented
(increased by 1) when the tray is opened.
※If the 2and 5button is pressed while oper-
ating, number of heat run is displayed for 3
seconds.
tConduct qto erepeatedly.
・H.R.SHORT display
・Heat run Short mode
Normal display except when 1light, 3light
qNormal display except when 1light, 3light
w
XXXX : No. of heat run repetitions
eNormal display except when 1light, 3light
r
XXXX : No. of heat run repetitions
No Key name Function Display
H.R.NORMAL
CD XXXX
CD XXXX
H.R.SHORT
CD XXXX
CD XXXX

17
DCD-F107
3.3 Automatic
mounting mode
・Press the /
13 button while name of the
H.R.CHACKING is displayed.
・Count this as the 0th heat run repetition.
qPlay the last track only on disc.
wThe heat run repetition no. is incremented
(increased by 1) when the tray is opened.
※If the 2and 5button is pressed while oper-
ating, number of heat run is displayed for 3
seconds.
eConduct qrepeatedly.
・H.R.CHACKING display
・Heat run short mode
Normal display except when 1flashing, 3flash-
ing
qNumber of heat run is display
XXXX : No. of heat run repetitions
・READING, CLOSEdisplay
Normal display except when 1flashing, 3flash-
ing
wNumber of heat run is display
XXXX : No. of heat run repetitions
3.4 Error display
E1-00 : Disc cannot be detected
E1-01 : Tracking offset adjustment not possible
E1-02 : Focus offset adjustment not possible
E2-00 : Focus servo dropped during playback.
E2-01 : Focus servo dropped during searching.
E2-03 : Focus servo dropped during TOC reading.
E2-05 : Focus servo dropped during manual
search.
E2-10 : Subcode can no longer be read during
playback
E2-11 : Subcode can no longer be read during
searching
E2-12 : Subcode can no longer be read during
TOC reading
E2-14 : Subcode cannot be read during pause
E2-15 : Subcode cannot be read during manual
search
E3-00 : TOC could not be read within specified
time
E3-01 : PVD/SVD analysis could not be
completed within specified time
E4-04 : Search time out
E4-05 : Error in communications with CD decoder
E5-00 : Inner switch not on
E6-00 : Inner switch not off
E8-00 : Tray is not opened by the specified time.
E8-01 : Tray is not closed by the specified time.
E9-01 : Other error
・,
13with mode light or flashing
X-XX : Error cord
No Key name Function Display
H.R.CHACKING
CD XXXX
CD XXXX
CD EX-XX

18
DCD-F107
3.4 Error display
qNumber of heat run is display
・Press the 9button while the error is displayed.
・No. heat runs is displayed for 5 seconds, the error
display reappears.
wThe track no. and time when the error occurred is
displayed
・Press the 8button while the error is displayed.
・The track no. and time when the error occurred is
displayed for 5 seconds, then error display
reappears.
q,
13with mode light or flashing
XXXX : No. of heat run repetitions
・Error display reappears after 5 seconds. See 3.4.
w,
13with mode light or flashing.
・Error display reappears after 5 seconds. See 3.4.
4
Main μ-com
Version up
mode
・AC is turned on while pressing the 5and 2button
same time on DCD-F107.(Entering the Service
mode)
･While displaying model name, when 2and the
ON/STANDBY button are pressed simultaneously,
the tray opens.
4.1 Start version up
• If an the 5or /
13button is pushed and a tray is
closed, a disc will be loaded and Version up will be
started.
• " FileError" is displayed when not found upgrade
file and the tray is opened.
qDuring a file search
wDuring a file check
e During deletion
r Writing
t When a file is not found
4.2 End version up
・After Version UP is completed, a tray is opened
and it stops in
5Cold start
(Initialize)
・AC is turned on while pressing the 5and 9
button same time on DCD-F107.
・The system is reset, and once this is completed
the unit is set to the normal mode.
DIMMER : 100%
DISC/USB : DISC
REMOTE/BROWSE : REMOTE
・The laser current initial value and laser
accumulated on time is not cleared.
No Key name Function Display
CD XXXX
CD 01 Tr 01:47
SYSTEM VUP ALL
SetDisc -> Close
SYSTEM VUP ALL
FileSearch
SYSTEM VUP ALL
FileCheck
SYSTEM VUP ALL
Erasig
SYSTEM VUP ALL
Writing
SYSTEM VUP ALL
FileError
SYSTEM VUP ALL
Complete
INITIALIZE

19
DCD-F107
6
USBμ-com
Version up
mode
・AC is turned on while pressing the 5and 2button
same time on DCD-F107.(Entering the Service
mode)
･While displaying model name, when 9and the
ON/STANDBY button are pressed simultaneously,
the tray opens.
6.1 Start version up
• If an the 5or /
13button is pushed and a tray is
closed, a disc will be loaded and Version up will
be started.
• "FileError" is displayed when not found upgrade
file and the tray is opened.
qDuring a file search
wDuring a file check
e During deletion
r Writing
t When a file is not found
6.2 End version up
・After Version UP is completed, a tray is opened
and it stops in
7EEPROM TEST
mode
・Press POWER SW while simultaneously pressing
ON/STANDBY and DISC/US button.
・POWER LED lights to the orange (TEST start).
・After EEPROM TEST, in the case of OK, LED
lights to the green.
・After EEPROM TEST, in the case of NG, LED
lights to the red.
・Mode is cancelled with POWER OFF.
No Key name Function Display
BOLERO VUP
SetDisc -> Close
SYSTEM VUP ALL
FileSearch
SYSTEM VUP ALL
FileCheck
SYSTEM VUP ALL
Erasig
SYSTEM VUP ALL
Writing
SYSTEM VUP ALL
FileError
BOLERO VUP
Complete

20
DCD-F107
Special mode transition diagram
9+ ON/STANDBY
2
+
ON/STANDBY
5+2+AC_ONService mode
Main μ-com
Ver.display
USB μ-com
Ver.display
CD test mode
Model Name display
“DCD-F107”
Main Ver. display reappears.
USB Ver UP mode
“Ver UP USB” display
Main Ver UP mode
“Ver UP Main” display
1/3
1/3
1/3
8or 9
2+1/3
2+1/3
1/3or
5
1/3or
5
2+1/3
2+1/3
2+1/3
2+1/3
2+1/3
9
9
9
9
9
8
9
9
8
8
8
8
8
8
1/3
Start
Ver UP

Start
Ver UP

H.R.NORMAL display
H.R.SHORT display
H.R.CHACKING display
FL tube The display for each grid. (It displays at intervals of 1 second.)
FL all light The entire display is flashing with an interval of about 1 second.
H.R.NORMAL operation TOC read →playback title-all of the disc. → OPEN →CLOSE → TOC read It displays repeatedly. H.R.SHORT operation TOC read →playback title-end of the disc. → OPEN →CLOSE → TOC read It displays repeatedly. H.R.CHACKING operation TOC read →OPEN → CLOSE →TOC read It displays repeatedly.