Denver 134094 User manual

1
CODING
- 134094
DENVER ASSEMBLY GUIDE
/ 3
’
Read the instructions carefully. Remove all the
wrappings , staples and straps from the carton. Refer
to the hardware and furniture part list for guidance.
Make sure that you have all the parts before you start
assembling. Place all the wooden furniture parts on a
clean, flat and soft surface, such as a carpet or
rubbermat to prevent scratches.
1
2
PART LIST
4
QTY
3
TOP PANEL
BOTTOM PANEL
1 PC
1 PC
1
2
3
3
4
5
5
6
6
7
8
8
SIDE PANEL
6
7
8
5MIDDLE PANEL
CENTER PANEL
BONE PANEL
METAL APRON
METAL LEG
1 PC
2 PCS
4 PCS
2 PCS
1 PC
2 PCS
MINI FIX
HARDWARE
A
B
C
D
E
F
G
18 SETS
ALLEN KEY M4 1 PC
H
I
M6 X 5OMM
CSK CAP WOOD SCREW
A1 A2 A3
M8 X 30MM WOOD DOWEL 22 PCS
2 PCS
8 PCS
8 PCS
16 PCS
8 PCS
4 PCS
M3.5 X 16MM C.B SCREW
M4 X 32MM C.B SCREW
JCBC Screw M6 x 20MM
JCBC SCREW M6 X 50MM
ONE HOLE L BRACKET (2MM)
SCREWDRIVER HAMMER
SELF-PREPARED TOOLS: Tools below are NOT included in package.

CODING
- 134094
DENVER ASSEMBLY GUIDE
/ 32
STEP 6
STEP 4
STEP 2
STEP 5
STEP 3
STEP 1
- Insert hardware A1 onto panel (1).
(Repeat 12 times.)
- Insert hardware A2 onto panel (1).
(Repeat 2 times.)
- Insert hardware B onto panel (1).
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
- Insert hardware A1 onto panel (2).
(Repeat 4 times.)
- Insert hardware B onto panel (2).
(Repeat 4 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
- Attach panel (5) to panel (1).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 8 times.)
OR
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
HARDWARE
D
A2
x2
ROTATE
x8
PRESS
B
PRESS
A1
x12 x4
PRESS
B
PRESS
A1
x4
PRESS
A1
x2
x4
PRESS
B
A2
x8
ROTATE
A2
x8
ROTATE
x4
ROTATE
I
E
x6
PRESS
B
Section View
x8 ROTATE
A2
A1
x8 PRESS
A3
Attach panel (6) to panel (2) by using hardware F.
(Repeat 8 times.)
SCREWDRIVER
REQUIRED
Fx8
ROTATE
1
1
2
2
33
45
5
5
6
6
6
* In this step hardware B are pre-inserted.
- Insert hardware A1 onto panel (4).
(Repeat 2 times.)
- Insert hardware A2 onto panel (3).
(Repeat 8 times.)
- Insert hardware B onto panel (4).
(Repeat 4 times.)
SCREWDRIVER
REQUIRED
* Ensure the arrows on hardware A1 point towards mounting positions.
- Assemble hardware I to panel (5) with hardware E.
(Repeat 4 times.)
- Insert hardware A2 onto panel (5).
(Repeat 8 times.)
- Insert hardware B onto panel (6).
(Repeat 6 times.)
SCREWDRIVER
REQUIRED

CODING
- 134094
DENVER ASSEMBLY GUIDE
/ 3
3
STEP 12
STEP 10
STEP 8
STEP 11
STEP 9
STEP 7
- Attach panel (4) to panel (1).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 2 times.)
OR
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
HARDWARE
D
- Attach panel (3) to panel (1) and (2).
- Insert all hardware A2 into A1.
- Rotate all A1 until tight.
- Apply A3 onto all A1.
(Repeat 8 times.)
OR
SCREWDRIVER
REQUIRED
* In this step hardware A1, A2 and B are pre-inserted.
HARDWARE
D
ROTATE
Section View
x2
A1
A2
x2 PRESS
A3
ROTATE
x8
A2 A1
PRESS
x8 A3
Assemble hardware I to panel (3) with hardware E.
(Repeat 4 times.)
SCREWDRIVER
REQUIRED
Connect panel (2) to panel (4) by using hardware C and D.
(Repeat 2 times.)
* In this step hardware B are pre-inserted.
HARDWARE
D
Connect Metal Apron (7) to panel (2) by using
hardware D and H.
(Repeat 8 times.)
HARDWARE
D
ROTATE
x8
H
D
Connect Metal Leg (8) to Metal Apron (7) by using
hardware D and G.
(Repeat 16 times.)
HARDWARE
D
ROTATE x16
G
D
1
1
1
11
2
2
22
3
3
3
3
3
4
4
4
44
7
7
8
8
8
8
ROTATE
x2
C
D
x4
ROTATE
E
I
1
2
3
3
4