Denver MT-1084NB User manual

ENG‐1
USER’S GUIDE
MT-1084NB
FUNCTIONS & CONTROLS
Side View
Front View
Stereo Headphone Jac
k
Audio/Video Output & Input
USB Por
t
Memory Card Por
t
DC Power Input
Power Switch
Remote Receiver
LCD Display Scree
n
Charge Indicato
r
Turns red when the portable DVD player is charging and off once the unit is fully charged
Power Indicato
r
Turns green when the portable DVD player is Powered on
Speake
r
Disc Doo
r
Open
Slide to Open the Disc Door
.
Mute
Presstomutevolume.
DVD/AV In
Press to select media source, DVD or AV Input.
Menu
Press to access the DVD menu.
Setup
Press to access the setup menu.
Volume −/+
Press and hold to adjust the volume.
Skip Back/Forward/Fast rewind/ Fast Forward
Press to skip between chapters or tracks.
Press to reverse or fast forward.
Play/Pause
Press to play or pause the loaded disc.
Stop
Press to stop play of the loaded disc.
DVD/SD/USB
Press to select DVD, SD memory card, or USB modes.

ENG‐2
REMOTE
Remote Battery
The remote control needs to install battery. When using remote control at the first time, please pull out the
insulation sheet from the button cell holder. The battery will be energized and ready to use.
Battery Installation/removal
Please note: Battery type required is “Cr2025”
TFT
LCD On/Off
MUTE
Press to mute the volume.
SETUP
Press to access the setup menu.
ARROWS /OK
OK is used for selecting; Up / Down / Left / Right directions buttons are used for
moving Up / Down / Left / Right in disc menu or setup menu.
AUDIO
Press to change the audio setting according to the disc.
OSD
Display current title and time of playback.
PLAY /PAUSE
BACKWARD
Press to rewind. Press to change the speed mode of rewind.
FORWARD
Press to fast forward. Press to change the speed mode of fast forward.
PREV
Press to skip back between chapters or tracks.
Next
Pull out the sheet
“+” Side
Open
Push

ENG‐3
Press to skip forward between chapters or tracks
MODE
Press to switch between AV IN and DVD mode.
SD /USB
Press to select between DVD, USB and SD/MMC card input.
REPEAT
Press to repeat the current chapter or track.
GO TO
Press to select the time you want to start playing with the number keys.
SUBTITLE
Press to switch caption and turn on or off.
PROG
Press to play contents of disc in the order you want by programming the track to be played.
ANGLE
On supported DVDs, press and hold to view alternate angles.
ZOOM
Press to zoom in or zoom out the image on the display when playing a loaded DVD.
VOLUME +/-
Press to adjust the volume level.
WIDE
Press to switch between different aspect ratio settings.
MENU
Press to access DVD disc menu.
TITLE
Press to access the title menu of a loaded DVD.
STOP
POWER
Power and Charging the Internal Battery
DC Power input: requires an AC/DC adapter, or 12V DC car adapter (included).
TO POWER THE UNIT, plug the included AC/DC adapter into the unit and a standard wall outlet.
If using in a car, plug the 12V DC car adapter into the unit and a standard 12V Power outlet in the car.
The Power Indicator will turn green whenever the portable DVD player is powered on.
The Charge Indicator will turn red whenever the battery is charging.
CONNECTING & PLAYING MEDIA
Loading and Playing a Disc
1. Slide the Open latchtoopentheDisc Door.
2. Load a disc into the DVD player, label side facing up. Close the Disc Door. After a disc is loaded, it will

ENG‐4
begin playing automatically.
3. If the disc does not begin playing automatically, press the Play/Pause button.
Programming a Loaded Disc
1. While the loaded disc is playing, press the PROG button on the remote control.
2. Use the Arrow buttons to select a program slot.
3. Use the Number Keypad to enter in the chapter and title, or track.
4. Titles and chapters, or tracks will play in the order they are listed.
5. Repeat step 3 until the desired titles and chapters, or tracks are programmed.
6. Use the Arrow buttons to highlight the on-screen START button. Press the OK button to begin playing the
programmed disc.
Connecting a USB Thumb Drive
AVI, VOB, MPEG 1, MPEG 2 and MPEG 4 video formats are supported.
1. Connect a USB thumb drive to the USB Port.
2. Press the DVD/SD/USB button to enter DVD/SD/USB mode.
3. Use the Up/Down Arrow and Play buttons to select USB mode and play content from the connected USB
thumb drive.
Connecting a Memory Card
AVI, VOB, MPEG 1, MPEG 2 and MPEG 4 video formats are supported. Note: Formats are not universally
compatible. Playback may be dependent on recording conditions.
1. Connect a SD or MMC memory card to the Memory Card Port.
2. Press the DVD/SD/USB button to enter DVD/MCR/USB mode.
3. Use the Up/Down Arrow and Play buttons to select MCR mode and play content from the connected
memory card.
Accessing the Setup Menu
To access the Setup Menu, press the Setup button on the DVD player or the remote control.
Using the 3.5mm AV Output
Require a 3.5mm to 3x RCA audio/video cable (included).
1. Connect the 3.5mm to 3x RCA audio/video cable to the AV Output on the unit’s display.
2. Connect the 3.5mm to 3x RCA audio/video cable to the RCA stereo audio inputs and composite video
input on a television.
3. Audio and video played through the portable DVD player will now be seen and heard through the
connected television.
Using the 3.5mm AV Input
Require a 3.5mm to 3 x RCA audio/video cable (included).
1. Connect the 3.5mm to 3 x RCA audio/video cable to the 3.5mm AV Input on the portable DVD player and
the composite video outputs on an audio/video source such, as a television.
2. Press the DVD/AV In button to switch to AV In mode.
3. Audio and video played from the connected source (a television) will now be output to the portable DVD
player.

ENG‐5
WARNING
a. Do not ingest battery, Chemical Burn Hazard
b. The remote control contains a coin / button cell battery. If the coin / button cell battery is swallowed, it can
cause severe internal burns in just 2 hours and can lead to death；
c. Keep new and used batteries away from children.
d. If the battery compartment does not close securely, stop using the product and keep it away from children
e. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate
medical attention
AC/DC adapter
Manufacturer’s name or trade mark, commercial
registration number and address
Shenzhen Technolog Co., Ltd
Address: Building A, No.21, XiFu Road, Red Star
Community, SongGang Street Baoan District ,
Shenzhen, Guangdong Province, 518105, P.R.China
Model identifier TEKA018-1201500EU
Input voltage 100-240V
Input AC frequency 50/60Hz
Output voltage 12.0V
Output current 1.5A
Output power 18.0W
Average active efficiency 86.64% at 115V 60Hz
86.67% at 230V 50Hz
Efficiency at low load (10%) 84.65% at 115V 60Hz
80.53% at 230V 50Hz
No-load power consumption 0.039W at 115V 60Hz
0.066W at 230V 50Hz

ENG‐6
Please notice - All products are subject to change without any notice. We take reservations for errors and
omissions in the manual.
ALL RIGHTS RESERVED, COPYRIGHT DENVER ELECTRONICS A/S
Electric and electronic equipment contains materials, components and substances that can be hazardous to your
health and the environment, if the waste material (discarded electric and electronic equipment) is not handled
correctly.
Electric and electronic equipment is marked with the crossed out trash can symbol, seen above. This symbol
signifies that electric and electronic equipment should not be disposed of with other household waste, but should
be disposed of separately.
All cities have established collection points, where electric and electronic equipment can either be submitted free
of charge at recycling stations and other collection sites, or be collected from the households. Additional
information is available at the technical department of your city.
DENVER ELECTRONICS A/S
Omega 5A, Soeften
DK-8382 Hinnerup
www.facebook.com/denverelectronics