designer's image 211-4569 User manual

01-13967-00 11/20
Shelf Kit with Pole
Assembly Instructions
SKU Reference # Finish
211-4569 4029 White
211-4570 4080 Java
211-4571 4049 Cottage
211-4670 14595 Charcoal
Tools Needed:
screwdriver drill w/
1/4 in. bit
level

2
SAFETY PRECAUTIONS
• This unit contains small parts which could be a choking hazard for small children. Children should be
under adult supervision at all times or serious injury could occur.
• Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to
become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings
may occur.
• Do not overload unit. If any shelf, top, or bottom of unit bows or bends, it is overloaded. The shelf, top, or
bottom could collapse and cause serious bodily injury and/or damage to personal belongings.
• Do not climb or step on the unit. This is not a bench. The unit may become unstable and either tip or
collapse. Serious bodily injury and/or damage to personal belongings may occur.
• Do not use this unit as a television stand. Serious bodily injury and/or damage to personal belongings
may occur.
• Do not mount or attach anything to the sides, rear, or front of the unit as this can create a force which can
cause the unit to tip. Serious bodily injury and/or damage to personal belongings may occur.
• All units must be secured individually to wall stud using hardware provided. If wall stud is not accessible,
consult your local hardware store for appropriate mounting hardware. Failure to do so may create an
unsafe tipping hazard that could lead to serious bodily injury and/or damage to personal belongings.
• Follow proper safety procedures if using power tools and ladders.
• We recommend you protect your work surface during assembly to prevent scratching or damage to table
tops, wood oors, etc.
• We recommend you hand-tighten screws. Use care not to overtighten if using power tools.
Serious or fatal crushing injuries can occur from
furniture tip-over. To help prevent tip-over:
- Install tip-over restraint provided.
- Unless specically designed to accommodate, do not
set TVs or other heavy objects on top of this product.
- Never allow children to climb or hang on drawers,
doors, or shelves.
- Place heavy items on lower shelves and as far back
as possible.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
WARNING
WARNING
STOP
FOLLOW
INSTRUCTIONS
CAREFULLY
Please do not return product to the retail store.
For product assistance and warranty information
please call Consumer Affairs at 1-800-874-0008.
Manufacturer Warranty
Manufacturer will replace any missing or damaged part
due to manufacturer defect. Please have proof of purchase.

3
A
B
C
(H3) x 6
long screw
(H6) x 2
hang rod bracket
Note: You will have extra hardware
depending on application.
(H2) x 14
small screw
(H5) x 1
back support
(H1) x 2
side support
(H4) x 6
wall anchor
DESCRIPTION QUANTITY
A top shelf 1
B inner hang rod 1
C outer hang rod 1
HARDWARE

4
If securing shelf from cabinet to cabinet:
1. Position the side support brackets (H1) so that they align with the top and front edges of the base cabinet. Do not align with front edge of the trim.
2. Secure the side support brackets into place using small screws (H2).
If securing shelf from cabinet to wall:
1. Position one side support bracket (H1) so that it aligns with the top and front edges of the base cabinet. Do not align with front edge of the trim.
2. Secure the side support bracket into place using small screws (H2).
3. Place the top shelf (A) onto the secured support bracket and make sure it is level. Mark the position of the other side support bracket (H2) against the open wall.
4. Predrill the bracket hole locations with a 1/4 in. hole. Insert wall anchors (H4) and secure the side support bracket with long screws (H3). Note: If installing
into a stud the anchor is not required.
STEP 1
(H4) x 2
wall anchor
(H2) x 4
small screw
(H2) x 2
small screw
(H3) x 2
long screw
(H1) x 2
side support
(H1) x 2
side support
(H1) (H1)
(H2)(H2)
(H3)
(H2) (H4)
Wall
Cabinet

5
STEP 2
1. Place the top shelf (A) onto the side support brackets (H1).
2. Center and mark the location of the back support bracket (H5) then remove top shelf.
3. Predrill the bracket hole locations with a 1/4 in. hole.
4. Insert wall anchors (H4) and secure the back support bracket with long screws (H3). Anchors are not required if installing directly into studs.
(H4) x 2
wall anchor
(H3) x 2
long screw
(H5) x 1
back support
A
(H5)
(H5)
(H4)
(H3)
Wall

6
1. Place the top shelf (A) back into position on the support brackets and secure using small screws (H2).
STEP 3
(H2) x 6
small screw
(H2)(H2)
(H2)

7
If securing hang rod from cabinet to cabinet:
1. Position the hang rod brackets (H6) into the desired position (approx. 2-1/8 in from top edge and 1-1/4 in from front edge) and secure using small screws (H2).
If securing hang rod from cabinet to wall:
1. Position the hang rod bracket (H6) into the desired position (approx. 2-1/8 in from top edge and 1-1/4 in from front edge) and secure using small screws (H2)
to cabinet.
2. Place the hang rod onto the secured hang rod bracket and make sure it is level. Mark the position of the other hang rod bracket (H6) against the open wall.
Predrill the bracket hole locations with a 1/4 in. hole. Insert wall anchors (H4) and secure the back support bracket with long screws (H3). Anchors are not
required if installing directly into studs.
STEP 4
(H2) x 4
small screw
(H2) x 2
small screw
(H6) x 2
hang rod bracket
(H6) x 2
hang rod bracket
(H2) (H2)
(H6) (H6)
(H6)
(H4)
(H3)
Wall
(H6)
(H2)
Cabinet
(H4) x 2
wall anchor
(H3) x 2
long screw

8
1. Slide the inner hang rod (B) into the outer hang rod (C) ensuring the bottom holes are on the outer edges.
2. Inset assembled hang rod (A & B) onto the hang rod brackets (H6) and lock into position.
STEP 5
B
B
C
C
(H6) (H6)