Dewenwils HRLS21B User manual

[Instruction Manual]
Remote Control Light Socket
Thank you for your purchase.
Please contact us if you have any questions.
We will get back to you within 24 hours.
Please attach your Order ID so that
we can serve you better.
V210818

1. Indoor use only. Avoid high humidity, high temperature, and areas with
a high magnetic field.
2. Always be sure to cut off the power before installing the receiver.
3. Don't connect any device that may exceed the performance limits of the
receiver.
4. Don't install or repair the product Only authorized service personnel
should undertake such installation and repairs.
5. If the remote is not in use for an extended period time, remove batteries.
6. Used batteries should be disposed of safely and properly.
7. To prevent a choking hazard, keep packing materials away from children.
8. Do not use the battery again if it is dropped or knocked out of shape.
Warning:
01
To reduce the risk of fire, electric shock, orpersonal injury,
please strictly follow the instructions.
Product Layout
Program button (On/Off button)
Indicator
1
2
ON
OFF
2
1

Operating Instructions
02
1. Remove the isolation tab in the battery compartment of the transmitter.
2. Press the ON/OFF button on the wall switch remote control to turn the
receiver on and off.
Canceling Programming
To remove a receiver from all transmitter parings (no remote transmitter
can control it):
1. Press the program button on the receiver for 6 seconds until the indicator
light starts toflash rapidly. (Note: The light flashes from slowly to rapidly.)

03
2. Release the program button and then press it again. The indicator light
will be off. All the programming has been canceled.
Programming the Receiver
The receivers and transmitters have been pre-paired for immediately use,
but there are few units may not be pre-programmed or programmed incorrectly,
or you want to customize the configuration to meet your needs.
To program a transmitter and receiver, please follow the steps below:

04
1. Press the program button on the receiver for 3 seconds until the indicator
light starts toflash slowly.
2. Release the program button and then press the “on” or “off ”button on the
remote control.
3. Programming / paring is successful when the indicator light stops blinking.
Note:
Each set of ON or OFF button can be paired with and control several outlets;
Each outlet can be paired and controlled by multiple transmitters.

Mounting the Wall Switch
Shown as the figure
Battery Replacement
1. If you find the receiver is working abnormally or the indicator on the
transmitter becomes dim, replace the remote battery with a new DC 12V
(type 23A) battery, making sure the polarity +/- of the battery is correct.
2. Low battery power may decrease readable wireless remote range.
3. Remove batteries if the remote is not in use for an extended period of
time.
05

- Input Voltage: 120VAC, 60Hz
- Max.load Power: Incandescent Bulb 60W; CFL/LED 20W
- Transmission Frequency: 433.92MHz
- Remote Control Distance: 80 Feet (Free Area)
- Remote Battery: 12V (23A)
- Socket Type: Standard Medium E26
Specifications
06
Troubleshooting
In the case that one receiver is unresponsive to the remote control, please
follow the steps below to resolve the issue:
1. If the wire switch receiver is unresponsive to the remote control, please
refer to the "Canceling Programming" and "Programming the Receiver"
sections in the manual to reprogram the receiver.
2. Make sure the receiver and appliance are properly connected and
powered on.
3. Replace the remote battery with a new 12V (23A) battery.
4. The remote transmitter may be too far away to control the receiver.
5. Make sure not to exceed the maximum load.
6. "Canceling Program" is always prior to"Programming the Receiver" when
you would like to make changes.

One Year Limited Warranty
DEWENWILS warrants this product to be free from defects in material and
workmanship for a period of one year from the date of purchase.
Warranty is void if damage is caused by misuse or improper installation.
Our dedicated customer service team will get back to you within 24 hours.
07