DFI-ITOX SB100-NRM User manual

SB100-NRM
System Board
User’s Manual
A16930145

Copyright
This publication contains information that is protected by copyright. No part of it
may be reproduced in any form or by any means or used to make any transfor-
mation/adaptation without the prior written permission from the copyright hold-
ers.
This publication is provided for informational purposes only. The manufacturer
makes no representations or warranties with respect to the contents or use
of this manual and specifically disclaims any express or implied warranties of
merchantability or fitness for any particular purpose. The user will assume the
entire risk of the use or the results of the use of this document. Further, the
manufacturer reserves the right to revise this publication and make changes to
its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
© 2011. All Rights Reserved.
Trademarks
All trademarks and registered trademarks of products appearing in this manual
are the properties of their respective holders.

FCC and DOC Statement on Class B
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or televi-
sion reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorientorrelocatethereceivingantenna.
• Increasetheseparationbetweentheequipmentandthereceiver.
• Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhich
the receiver is connected.
• ConsultthedealeroranexperiencedradioTVtechnicianforhelp.
Notice:
1. The changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission
limits.

1
4
Introduction Table of Contents
Copyright������������������������������������������������������������������������������������������� 2
Trademarks���������������������������������������������������������������������������������������� 2
FCC and DOC Statement on Class B���������������������������������������������� 3
About this Manual ����������������������������������������������������������������������������� 6
Warranty ������������������������������������������������������������������������������������������ 6
Static Electricity Precautions������������������������������������������������������������� 7
Safety Measures ��������������������������������������������������������������������������������� 7
About the Package ���������������������������������������������������������������������������� 8
Before Using the System Board �������������������������������������������������������� 8
Chapter 1 - Introduction ������������������������������������������������������������������ 9
Specifications���������������������������������������������������������������������������������� 9
Features �������������������������������������������������������������������������������������� 11
Chapter 2 - Hardware Installation�������������������������������������������������� 14
System Board Layout �������������������������������������������������������������������� 14
System Memory ��������������������������������������������������������������������������� 15
Installing the DIM Module ��������������������������������������������������������� 17
CPU �������������������������������������������������������������������������������������������� 19
Installing the CPU �������������������������������������������������������������������� 20
Installing the Fan and Heat Sink ������������������������������������������������ 24
Jumper Settings����������������������������������������������������������������������������� 26
Clear CMOS Data ��������������������������������������������������������������������� 26
PS/2 Power Select�������������������������������������������������������������������� 27
USB Power Select��������������������������������������������������������������������� 28
Power-on Select����������������������������������������������������������������������� 29
COM1/COM2 RS232/RS422/RS485 Select������������������������������������ 30
COM1/COM2 RS232/Power Select����������������������������������������������� 31
Rear Panel I/O Ports��������������������������������������������������������������������� 32
PS/2 Mouse and PS/2 Keyboard Ports����������������������������������������� 33
COM (Serial) Ports ������������������������������������������������������������������� 34
VGA Port��������������������������������������������������������������������������������� 35
DVI-I Port ������������������������������������������������������������������������������� 36
RJ45 LAN Ports ������������������������������������������������������������������������ 37
USB Ports�������������������������������������������������������������������������������� 38
Audio�������������������������������������������������������������������������������������� 40

1
5
Introduction
I/O Connectors............................................................................ 42
S/PDIF Connector..................................................................... 42
Digital I/O Connectors .............................................................. 43
SATA (Serial ATA) Connectors .................................................... 44
Cooling Fan Connectors............................................................. 45
Chassis Instrusion Connector .................................................... 46
Power Connectors .................................................................... 47
Standby Power LED .................................................................. 48
Front Panel Connectors ............................................................. 49
Expansion Slots ....................................................................... 50
Battery ................................................................................... 51
Chapter 3 - BIOS Setup.................................................................. 52
Overview ..............................................................................................................52
AMI BIOS Setup Utility ................................................................. 54
Main ....................................................................................... 54
Advanced ................................................................................ 55
Chipset ................................................................................... 70
Boot ....................................................................................... 76
Security .................................................................................. 78
Save & Exit ............................................................................. 80
Updating the BIOS........................................................................ 81
Chapter 4 - Supported Software ................................................... 82
Chapter 5 - RAID ........................................................................ 106
RAID Levels .......................................................................................................106
Settings................................................................................................................107
Chapter 6 - Intel AMT Settings ................................................... 112
Overview ............................................................................................................112
Enable Intel®AMT in the AMI BIOS ............................................................113
Enable Intel®AMT in the Intel®Management Engine BIOS
Extension (MEBX) Screen ..............................................................................116
Appendix A - NLITE and AHCI Installation Guide ....................... 145
Appendix B - Watchdog Sample Code ......................................... 157
Appendix C - System Error Message............................................ 158
Appendix D - Troubleshooting...................................................... 160

1
6
Introduction
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual
in the CD, insert the CD into a CD-ROM drive. The autorun screen (Main Board
Utility CD) will appear. Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the
product, inability to use the product, unauthorized replacement or alteration
of components and product specifications.
2. The warranty is void if the product has been subjected to physical abuse,
improper installation, modification, accidents or unauthorized repair of the
product.
3. Unless otherwise instructed in this user’s manual, the user may not, under
any circumstances, attempt to perform service, adjustments or repairs on the
product, whether in or out of warranty. It must be returned to the purchase
point, factory or authorized service agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequencial
damages to the product that has been modified or altered.

1
7
Introduction
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components
or devices even before installing them in your system unit. Static electrical dis-
charge can damage computer components without causing any signs of physical
damage. You must take extra care in handling them to ensure against electro-
static build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag
until you are ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the compo-
nents, contacts or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold
modules or connectors by their ends.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and
other components. Perform the upgrade instruction procedures described
at an ESD workstation only. If such a station is not available, you can
provide some ESD protection by wearing an antistatic wrist strap and
attaching it to a metal part of the system chassis. If a wrist strap is
unavailable, establish and maintain contact with the system chassis
throughout any procedures requiring ESD protection.
Safety Measures
To avoid damage to the system:
• UsethecorrectACinputvoltagerange.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for instal-
lation or servicing. After installation or servicing, cover the system chassis
before plugging the power cord.
Battery:
• Dangerofexplosionifbatteryincorrectlyreplaced.
• Replace only with the same or equivalent type recommend by the manufac-
turer.
• Disposeofusedbatteriesaccordingtolocalordinance.

1
8
Introduction
About the Package
The system board package contains the following items. If any of these items are
missing or damaged, please contact your dealer or sales representative for as-
sistance.
One system board
One PS/2 Keyboard/Mouse cable (optional)
Two Serial ATA data cables
Two Serial ATA power cables
Two USB port cables
One COM port cable (with bracket)
One I/O shield
One DVD
One QR (Quick Reference)
The system board and accessories in the package may not come similar to the
information listed above. This may differ in accordance to the sales region or
models in which it was sold. For more information about the standard package in
your region, please contact your dealer or sales representative.
Before Using the System Board
Before using the system board, prepare basic system components.
If you are installing the system board in a new system, you will need at least the
following internal components.
• A CPU
• Memory module
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will nor-
mally include at least a keyboard, a mouse and a video display monitor.

1
9
Introduction
Processor
Chipset
System Memory
Expansion Slots
Graphics
Audio
LAN
Serial ATA
Chapter 1 - Introduction
• LGA 1155 socket for:
- Intel®CoreTM i7-2600 (3.4GHz, 95W)
- Intel®CoreTM i5-2400 (3.1GHz, 95W)
- Intel®CoreTM i3-2120 (3.3GHz, 65W)
- Intel®Pentium® G850
• New microarchitecture on 32nm process technology
• Intel®Advanced Vector Extensions (Intel®AVX) Instructions
• Intel®Turbo Boost Technology
• Intel®Q67 PCH (Platform Controller Hub)
• Two 240-pin DDR3 DIMM sockets
• Supports DDR3 1066/1333MHz
• Supports up to 16GB system memory
• Supports dual channel memory interface
• DRAM device technologies: 1Gb, 2GB and 4Gb DDR3 DRAM
technologies are supported for x8 and x16 devices, unbuf-
fered, non-ECC
• 1 PCI Express Gen 2 x16 slot (PCIE 2.0)
• Intel®HD Graphics
• Display ports: DVI-I (DVI-D signal) and VGA
• DVI-I supports up to 1920x1200 @ 60Hz resolution
• VGA supports up to 2048x1536 @ 75Hz resolution
• Supports 6 Graphics Execution Units (EUs)
• Intel®Clear Video Technology
• DirectX Video Acceleration (DXVA) support for accelerating
video processing
• Realtek ALC262 2-channel High Definition Audio
• High performance DACs with 100dB SNR
• ADCs with 90dB SNR
• Two stereo DACs support 24-bit PCM format for stereo au-
dio playback
• Three stereo ADCs support 20-bit PCM format for multiple
input streaming
• S/PDIF audio interface
• Intel 82579LM with iAMT7.0 Gigabit Ethernet Phy
• Intel 82574L PCI Express Gigabit Ethernet controller
• Integrated 10/100/1000 transceiver
• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab
• Supports wire management
• 4 Serial ATA ports
- 2 SATA 2.0 ports with data transfer rate up to 3Gb/s
- 2 SATA 3.0 ports with data transfer rate up to 6Gb/s
• Integrated Advanced Host Controller Interface (AHCI) con-
troller
• Supports RAID 0, RAID 1, RAID 5 and RAID 10
Specifications

1
10
Introduction
Intel Active
Management
Technology
(AMT)
TPM (optional)
Rear Panel I/O
Ports
I/O Connectors
BIOS
Energy Efficient
Design
Damage Free
Intelligence
Temperature
Humidity
Dimensions
• Supports iAMT7.0
• Out-of-band system access
• Remote troubleshooting and recovery
• Hardware-based agent presence checking
• Proactive alerting
• Remote hardware and software asset tracking
• TPM - Trusted Platform Module
• Provides a Trusted PC for secure transactions
• Provides software license protection, enforcement and pass-
word protection
• 1 mini-DIN-6 PS/2 mouse port and PS/2 keyboard port
• 1 mini-DIN-6 PS/2 keyboard port
• 2 DB-9 serial ports
- Supports RS232/422/485 (RS232 and/or Power)
• 1 DB-15 VGA port
• 1 DVI-I port (DVI-D signal)
• 2 RJ45 LAN ports
• 4 USB 2.0/1.1 ports
• Mic-in, line-in and line out jacks
• 2 connectors for 4 external USB 2.0/1.1 ports
• 2 connectors for 2 external RS232 serial ports
• 1 8-bit Digital I/O connector
• 1 Digital I/O power connector
• 1 front audio connector for line-out and mic-in jacks
• 1 S/PDIF connector
• 4 Serial ATA ports
• 1 24-pin ATX power connector and 1 4-pin 12V power connector
• 1 chassis intrusion connector and 1 front panel connector
• 2 fan connectors
• AMI BIOS
• 64Mbit SPI BIOS
• Supports ErP Lot6 power saving (optional)
• Supports ACPI
• System Power Management
• Wake-On-Events include:
- Wake-On-PS/2 KB/Mouse
- Wake-On-USB KB/Mouse
- Wake-On-LAN
- RTC timer to power-on the system
• CPU stopped clock control
• AC power failure recovery
• Monitors CPU/system temperature and overheat alarm
• Monitors VCORE/5V/3.3V/V_DIMM/12V/5VSB voltages and
failure alarm
• Monitors CPU/system fan speed and failure alarm
• Read back capability that displays temperature, voltage and
fan speed
• Watchdog timer function
• 0oC to 60oC
• 10% to 90%
• Mini-ITX form factor
• 170mm (6.7”) x 170mm (6.7”)

1
11
Introduction
Features
Watchdog Timer
The Watchdog Timer function allows your application to regularly “clear” the sys-
tem at the set time interval. If the system hangs or fails to function, it will reset
at the set time interval so that your system will continue to operate.
DDR3
DDR3 delivers increased system bandwidth and improved performance. It offers
peak data transfer rate of up to 21 Gb/s bandwidth. The advantages of DDR3
are its higher bandwidth and its increase in performance at a lower power than
DDR2.
Graphics
The integrated Intel HD graphics for graphics intensive applications delivers ex-
ceptional3D,2Dandvideocapabilities.ItsupportsVGAandDVIinterfaces.
DVI
DVI (Digital Visual Interface) is a form of video interface technology made to
maximize the quality of flat panel LCD monitors and modern video graphics
cards. Data is transmitted using the TMDS (Transition Minimized Differential Sig-
naling) protocol, providing a digital signal from the PC’s graphics subsystem to
the display.
PCI Express
PCI Express is a high bandwidth I/O infrastructure that possesses the ability to
scale speeds by forming multiple lanes. The x4 PCI Express lane supports trans-
fer rate of 1 Gigabyte per second. The PCI Express architecture also provides a
high performance graphics infrastructure by enhancing the capability of a x16 PCI
Expresslanetoprovide8Gigabytespersecondtransferrate.
Intel Active Management Technology (AMT)
Intel Active Management Technology (Intel®AMT) allows remote access and man-
agement of networked systems even while PCs are powered off, remotely repair
systems after OS failures and has the capability to remotely update all systems
with the latest security software.
Audio
The Realtek ALC262 audio codec provides 2-channel High Definition audio output.

1
12
Introduction
Serial ATA
Serial ATA is a storage interface that is compliant with SATA 1.0a specifica-
tion. SATA 3.0 supports speed up to 6Gb/s while SATA 2.0 supports speed up to
3Gb/s. This improves hard drive performance faster than the standard parallel
ATA whose data transfer rate is 100MB/s. The board supports RAID 0/1/5/10.
Gigabit LAN
TheIntel W82579LMPHY andRealtekRTL8111DLPCIExpress Gigabit controllers
supportupto1Gbpsdatatransmission.
USB
The system board supports USB 2.0 and USB 1.1 ports. USB 1.1 supports 12Mb/
second bandwidth while USB 2.0 supports 480Mb/second bandwidth providing a
marked improvement in device transfer speeds between your computer and a
wide range of simultaneously accessible external Plug and Play peripherals.
Wake-On-LAN
This feature allows the network to remotely wake up a Soft Power Down (Soft-
Off) PC. It is supported via the onboard LAN port or via a PCI LAN card that uses
the PCI PME (Power Management Event) signal. However, if your system is in the
Suspend mode, you can power-on the system only through an IRQ or DMA inter-
rupt.
Important:
The 5V_standby power source of your power supply must support
≥720mA.
Wake-On-PS/2
This function allows you to use the PS/2 keyboard or PS/2 mouse to power-on
the system.
Important:
The 5V_standby power source of your power supply must support
≥720mA.
Wake-On-USB
This function allows you to use a USB keyboard or USB mouse to wake up a sys-
tem from the S3 (STR - Suspend To RAM) state.
Important:
If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB
ports, the 5V_standby power source of your power supply must support
≥1.5A. For 3 or more USB ports, the 5V_standby power source of your
powersupplymustsupport≥2A.

1
13
Introduction
RTC Timer
The RTC installed on the system board allows your system to automatically pow-
er-on on the set date and time.
ACPI STR
The system board is designed to meet the ACPI (Advanced Configuration and
Power Interface) specification. ACPI has energy saving features that enables PCs
to implement Power Management and Plug-and-Play with operating systems that
support OS Direct Power Management. ACPI when enabled in the Power Manage-
ment Setup will allow you to use the Suspend to RAM function.
With the Suspend to RAM function enabled, you can power-off the system at
once by pressing the power button or selecting “Standby” when you shut down
Windows®without having to go through the sometimes tiresome process of
closing files, applications and operating system. This is because the system is
capable of storing all programs and data files during the entire operating session
into RAM (Random Access Memory) when it powers-off. The operating session will
resume exactly where you left off the next time you power-on the system.
Important:
The 5V_standby power source of your power supply must support
≥720mA.
Power Failure Recovery
When power returns after an AC power failure, you may choose to either power-
on the system manually or let the system power-on automatically.

14
2Hardware Installation
System Board Layout
Chapter 2 - Hardware Installation
1
Mic-in
Line-in
Line-out
LAN 2
USB 9
USB 8
LAN 1
USB 1
USB 0
DVI-I port
(DVI-D signal only)
VGA
DVI-I
COM 2
COM 1
Mouse
KB
DDR3_1
DDR3_2
Front
panel
1
11
Battery
SATA 0
1
SATA 1
11
SATA 4
SATA 5
1
ATX power
12
24
1
SPI Flash
BIOS
1
COM3 COM4
1
2
91
2
9
9
1
Front audio 1
+12V
power
CPU fan
1
1
PS/2 power
select (J )P2
1
2
5
6
1
2
5
6
JP3 JP5
1
1
USB 0-1,8-9
power select
(J )P4
USB 2-5 power
select (J )P7
JP1
JP6
JP8
JP9
1DIO power DIO
1
Power-on select ( )JP8
Clear CMOS ( )JP9
Intel
Q67
Socket 1155
1
1
1S/PDIF
ASMedia
1442
Intel
WG82574L
Realtek
ALC262
Fintek F81217U
1
2
9
10
USB 4-5 1
2
9
10
USB 2-3
12
6
PCIE x16
Standby
Power LED
12
6
5
5
COM1(JP3), COM2(JP5):
RS232/Power select
COM1(JP1), COM2(JP6):
RS232/422/485 select
System fan
Chassis
intrusion
1
6Gb/s 3Gb/s
Intel
Q67

15
2
Hardware Installation
1
Intel
Q67
Intel
Q67
System Memory
Important:
Electrostatic discharge (ESD) can damage your system board, processor,
disk drives, add-in boards, and other components. Perform the upgrade
instruction procedures described at an ESD workstation only. If such a
station is not available, you can provide some ESD protection by wearing
an antistatic wrist strap and attaching it to a metal part of the system
chassis. If a wrist strap is unavailable, establish and maintain contact
with the system chassis throughout any procedures requiring ESD pro-
tection.
DDR3-2
DDR3-1
Standby
Power LED
Important:
When the Standby Power LED lit red, it indicates that there is power on
the system board. Power-off the PC then unplug the power cord prior to
installing any devices. Failure to do so will cause severe damage to the
motherboard and components.
Features
• Two 240-pin DDR3 DIMM sockets
• Supports DDR3 1066/1333MHz
• Supports dual channel memory interface
• Supports up to 16GB system memory

16
2Hardware Installation
The system board supports the following memory interface.
Single Channel (SC)
Data will be accessed in chunks of 64 bits (8B) from the memory channels.
Dual Channel (DC)
Data will be accessed in chunks of 128 bits from the memory channels. Dual
channel provides better system performance because it doubles the data transfer
rate.

17
2
Hardware Installation
Note:
The system board used in the following illustrations may not resemble
the actual board. These illustrations are for reference only.
Installing the DIM Module
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
3. Locate the DIMM socket on the system board.
4. Push the “ejector tabs” which are at the ends of the socket to the side.
Ejector tab
Ejector tab
5. Note how the module is keyed to the socket.
Key
Notch

18
2Hardware Installation
7. Seatthe modulevertically, pressingit downrmly until itis completelyseat-
ed in the socket.
6. Grasping the module by its edges, position the module above the socket with
the “notch” in the module aligned with the “key” on the socket. The keying
mechanism ensures the module can be plugged into the socket in only one
way.
8. The ejector tabs at the ends of the socket will automatically snap into the
locked position to hold the module in place.

19
2
Hardware Installation
CPU
The system board is equipped with a surface mount LGA 1155 socket. This sock-
et is exclusively designed for installing a LGA 1155 packaged Intel CPU.
Important:
1. Before you proceed, make sure (1) the LGA 1155 socket comes with
a protective cap, (2) the cap is not damaged and (3) the socket’s
contact pins are not bent. If the cap is missing or the cap and/or
contact pins are damaged, contact your dealer immediately.
2. Make sure to keep the protective cap. RMA requests will be accepted
and processed only if the LGA 1155 socket comes with the protective
cap.
Protective
cap
Note:
The system board used in the following illustrations may not resemble
the actual board. These illustrations are for reference only.

20
2Hardware Installation
1
Intel
Q67
Intel
Q67
Installing the CPU
1. Make sure the PC and all other peripheral devices connected to it has been
powered down.
2. Disconnect all power cords and cables.
3. Locate the LGA 1155 CPU
socket on the system
board.
Important:
The CPU socket must not
come in contact with any-
thing other than the CPU.
Avoid unnecessary expo-
sure. Remove the protec-
tive cap only when you are
about to install the CPU.
4. Unlock the socket by push-
ing the load lever down,
moving it sideways until it
is released from the reten-
tion tab; then lift the load
lever up.
Retention tab
Load lever