DFI WM343-SD330 User manual

1
Chapter 1 Introduction www.d.com
WM343-SD330/SD331
Desktop Box PC
User’s Manual
A47300805

2
Chapter 1 Introduction www.d.com
Copyright
This publication contains information that is protected by copyright. No part of it may be re-
produced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particu-
lar purpose. The user will assume the entire risk of the use or the results of the use of this
document. Further, the manufacturer reserves the right to revise this publication and make
changes to its contents at any time, without obligation to notify any person or entity of such
revisions or changes.
Changes after the publication’s first release will be based on the product’s revision. The web-
site will always provide the most updated information.
© 2018. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class A
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.

3
Chapter 1 Introduction www.d.com
Table of Contents
Copyright���������������������������������������������������������������������� 2
Trademarks ������������������������������������������������������������������ 2
FCC and DOC Statement on Class A ���������������������������� 2
About this Manual �������������������������������������������������������� 4
Warranty ��������������������������������������������������������������������� 4
Static Electricity Precautions ��������������������������������������� 4
Safety Measures����������������������������������������������������������� 4
Safety Precautions ������������������������������������������������������� 5
About the Package ������������������������������������������������������� 5
Before Using the System ��������������������������������������������� 5
Chapter 1 - Introduction���������������������������������������������� 6
Chapter 2 - Getting Started ��������������������������������������� 12
Chapter 3 - Installing Devices ����������������������������������� 13
Chapter 4 - Jumper Settings ������������������������������������ 22
Clear CMOS ...........................................................................22
Serial Port RS232/422/485 Select ........................................... 23
Serial Port Power Select .........................................................25
Power-on Select ..................................................................26
Backlight Power Select (for SD330-Q170/H110 only) ............... 27
Panel Power Select (for SD330-Q170/H110 only)..................... 27
LCD/Inverter Power Select (for SD330-Q170/H110 only).......... 28
Mini PCIe/mSATA Signal Select (for SD330-Q170 only) ............ 28
Chapter 5 - Ports and Connectors ���������������������������� 29
Rear Panel I/O Ports ..............................................................29
PS/2 Keyboard/Mouse Port.......................................................................... 29
COM (Serial) Ports ...................................................................................... 30
Graphics Interfaces..................................................................................... 30
RJ45 LAN Ports........................................................................................... 31
USB Ports................................................................................................... 31
Audio ........................................................................................................ 32
I/O Connectors ...................................................................... 33
S/PDIF Connector ....................................................................................... 33
Digital I/O and Power Connector ................................................................. 34
SATA (Serial ATA) Connectors...................................................................... 35
COM (Serial) Ports ...................................................................................... 36
USB Ports................................................................................................... 37
Cooling Fan Connectors............................................................................... 38
Chassis Intrusion Connector ....................................................................... 39
LPC Connector............................................................................................ 40
Power Connectors....................................................................................... 41
SMBus Connector ...................................................................................... 42
Standby Power LED .................................................................................... 43
Battery....................................................................................................... 43
Front Panel Connector ................................................................................ 44
Expansion Slots .......................................................................................... 45
LVDS LCD Panel Connector ......................................................................... 46
Chapter 6 - Mounting Options ����������������������������������� 47
Chapter 7 - BIOS Setup ��������������������������������������������� 49
Overview ..............................................................................49
Insyde BIOS Setup Utility.......................................................50
Main .......................................................................................................... 50
Advanced .................................................................................................. 50
Device Manager.......................................................................................... 57
Security...................................................................................................... 62
Boot........................................................................................................... 63
Exit............................................................................................................ 64
Updating the BIOS................................................................. 65
Notice: BIOS SPI ROM ...........................................................65
Chapter 8 - Supported Software�������������������������������� 66
Chapter 9 - RAID ������������������������������������������������������ 78
Chapter 10 - Intel AMT Settings ������������������������������� 82

4
Chapter 1 Introduction www.d.com
About this Manual
An electronic file of this manual is included in the CD. To view the user’s manual in the CD,
insert the CD into a CD-ROM drive. The auto-run screen (Main Board Utility CD) will appear.
Click “User’s Manual” on the main menu.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper instal-
lation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequential damages to the
product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other com-
ponents. Perform the upgrade instruction procedures described at an ESD worksta-
tion only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chas-
sis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.

5
Chapter 1 Introduction www.d.com
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• 1 WM343-SD330 or WM343-SD331 System Unit
• 1 CPU cooler
• 1 SATA Data Cable (Length: 650mm)
• 4 HDD Screws
• 1 PSU Flex ATX 150W/250W/350W/400W/500W
• 1 System Fan
Optional Items
• Power Cord
• 3.5” HDD Tray Kit
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Before Using the System
Before powering-on the system, prepare the basic system components.
If you are installing the system board in a new system, you will need at least the following
internal components.
• CPU and memory modules
• Storage devices such as hard disk drive, CD-ROM, etc.
You will also need external system peripherals you intend to use which will normally include at
least a keyboard, a mouse and a video display monitor.
Safety Precautions
• Use the correct DC input voltage range.
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
• Keep this system away from humidity.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.

6
Chapter 1 Introduction www.d.com
Chapter 1 - Introduction
Chapter 1
Overview
Key Features
Model Name WM343-SD
Processor 6th Generation Intel®CoreTM, Pentium®and Celeron®processors
Chipset Intel® C236 / Q170 / H110 Chipset
LAN 2 LAN ports
COM 1 COM port
Displays
1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
USB 4 USB 3.0 ports + 2 USB 2.0 ports
Audio Mic-in, Line-out, Line-in (available upon request)
Front View
Rear View

7
Chapter 1 Introduction www.d.com
Specifications
Chapter 1
System Processor 6th Generation Intel®CoreTM Processors (LGA 1151 Socket)
Intel® Xeon®Processor E3-1275 v5, Quad Core, 8M Cache,
3.6GHz (4.0GHz), 80W
Intel® Xeon®Processor E3-1225 v5, Quad Core, 6M Cache,
3.3GHz (3.7GHz), 80W
Intel® Xeon®Processor E3-1268L v5, Quad Core, 8M Cache,
2.4GHz (3.4GHz), 35W
Intel® Core™ i7-6700 Processor, Quad Core, 8M Cache,
3.4GHz (4.0GHz), 65W
Intel® Core™ i7-6700TE Processor, Quad Core, 8M Cache,
2.4GHz (3.4GHz), 35W
Intel® Core™ i5-6500 Processor, Quad Core, 6M Cache,
3.2GHz (3.6GHz), 65W
Intel® Core™ i5-6500TE Processor, Quad Core, 6M Cache,
2.3GHz (3.3GHz), 35W
Intel® Core™ i3-6100 Processor, Dual Core, 4M Cache, 65W
Intel® Core™ i3-6100TE Processor, Dual Core, 4M Cache,
2.7GHz, 35W
Intel® Pentium®Processor G4400, Dual Core, 3M Cache,
3.3GHz, 65W
Intel® Pentium®Processor G4400TE, Dual Core, 3M Cache,
2.9GHz, 35W
Intel® Celeron®Processor G3900, Dual Core, 2M Cache,
2.8GHz, 65W
Intel® Celeron®Processor G3900TE, Dual Core, 2M Cache,
2.6GHz, 35W
Chipset WM343-SD330
SD330-Q170: Intel® Q170 Chipset
SD330-H110: Intel®H110 Chipset
WM343-SD331
SD331-C236: Intel®C236 Chipset
SD331-Q170: Intel®Q170 Chipset
Memory WM343-SD331 (SD331-C236/SD331-Q170)
Four 288-pin ECC/non-ECC DIMM up to 64GB, dual channel DDR4
1866/2133MHz
WM343-SD330 (SD330-Q170)
Four 288-pin DIMM up to 64GB, dual channel DDR4 1866/2133MHz
WM343-SD330 (SD330-H110):
Two 288-pin DIMM up to 32GB, dual channel DDR4 1866/2133MHz
Graphics Controller Intel® HD Gen 9 Graphics
Feature OpenGL 5.0, DirectX 12, OpenCL 2.1
HW Decode: AVC/H.264, MPEG2, VC1/WMV9, JPEG/MJPEG, HEVC/H265, VP8, VP9
HW Encode: MPEG2, AVC/H264, JPEG, HEVC/H265, VP8, VP9
Display 1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
1 x LVDS (only for SD330-Q170/SD330-H110)
VGA: resolution up to 1920x1200 @ 60Hz
DVI-I: resolution up to 1920x1200 @ 60Hz
DP++: resolution up to 4096x2304 @ 60Hz
LVDS: dual channel, resolution up to 1920x1200 @ 60Hz
Triple
Display
VGA + DVI-I (DVI-D signal) + DP++
Storage External 1 or 2 x 3.5"/2.5" SATA 3.0 Drive Bays (1 x 3.5" SATA drive bay, by default)
1 x 5.25" Optical Drive Bay
Expansion Interface WM343-SD330
1 x PCIe x16 (Gen 3)
1 x PCIe x4 (Gen 3)
2 x PCI
1 x Full-size Mini PCIe (USB/PCIe/mSATA, PCIe by default) (only for
SD330-Q170)
WM343-SD331
2 x PCIe x16 (1 x16 or 2 x8 signal) (Gen 3)
2 x PCIe x4 (Gen 3)
Audio Codec Realtek ALC888S-VD2-GR

8
Chapter 1 Introduction www.d.com
Environment Operating
Temperature
0 to 45°C
Storage
Temperature
0 to 60°C
Relative
Humidity
5 to 95% RH (non-condensing)
Mechanical Shock Operating: 3G
Non-operating: 5G
Vibration Operating: Random 5~500Hz 0.5G
Non-operating: Sine 10~500Hz 1.5G
Package
Drop
ISTA Project 1A
Chapter 1
WatchDog
Timer
Output &
Interval
System Reset, Programmable via Software from 1 to 255 Seconds
Power Supply Flex ATX 250W (or optional 150/250/350/400/500W)
OS Support
and BIOS
OS Windows 7 (/WES7) 32/64-bit
Windows 8.1 (64-bit)
Windows 10 IoT Enterprise 64-bit
Debian 8 (with VESA graphics driver)
CentOS 7 (with VESA graphics driver)
Ubuntu 15.10 (Intel graphics driver available)
BIOS Insyde SPI 128Mbit
Mechanical Construction Sheet Metal
Compliance Wall Mount
Dimensions 349mm x 140.2mm x 290.9mm (13.74" x 5.52" x 11.45")
Weight TBD
ETHERNET Controller 1 x Intel®I210AT PCIe (10/100/1000Mbps)
1 x Intel®I219LM PCIe with iAMT11.0 (10/100/1000Mbps)
LED Indicators 1 x Power LED
1 x HDD LED
REAR I/O Ethernet 2 x GbE (RJ-45)
Serial 1 x RS-232/422/485 (RS-232 w/ power) (DB-9)
USB 4 x USB 3.0
2 x USB 2.0
PS/2 1 x PS/2 (mini-DIN-6)
Display 1 x VGA
1 x DVI-I (DVI-D signal)
1 x DP++
Audio 1 x Line-out, 1 x Mic-in, 1 x Line-in (available upon request)
Buttons 1 x Power Button
Cooling Fan 1 x System Fan

9
Chapter 1 Introduction www.d.com
DVI-I/DP++/VGA Port
Connects the DVI-I (DVI-D signal)/DP++/VGA connector of an LCD monitor.
COM Port
Connects serial devices. COM 1 can be selected among RS232, RS422 and RS485 as well as
between RS232 and RS232 with power via jumper settings.
USB 3�0 Ports
Connect USB 3.0 devices and devices based on USB 2.0 and 1.1/1.0 versions.
USB 2�0 Ports
Connect USB 2.0 devices and devices based on USB 1.1/1.0 versions.
LAN Ports
Connect the system to a local area network.
Line-out
Connects an external speaker.
Line-in (optional)
Connects any audio devices such as CD players, audio mixers, musical instruments, etc.
Mic-in
Connects an external microphone.
PS/2 KB/Mouse
Connects a PS/2 keyboard and mouse.
Expansion slots
Provides PCIe or PCI expansion connectivity.
Power Button
Press to power on or off the system.
Status LED (Green)
Indicates system status.
HDD LED (Red)
Indicates the status of hard drives.
SATA Drive Bay
Inserts a SATA drive.
Optical Drive Bay
Inserts a DVD or CD-ROM. Note that this bay can also be an optional 3.5” SATA drive bay.
Chapter 1
Getting to Know the WM343-SD
Front View
Status LED
ACPI state S0 Sleep S4, S5
LED Behavior ON Blinking Off
HDD LED
HDD State Disk access
activity Disk drives present or not present
LED Behavior Blinking Off
Rear View
Power Button
Optical
Drive Bay
SATA
Drive Bay
Expansion
Slots
USB 3.0 Ports
DVI-I
DP++
PS/2 Keyboard/Mouse
USB 2.0 Ports
COM
VGA
Line-in (optional)
Line-out
Mic-in
HDD LED
Status LED LAN Ports

10
Chapter 1 Introduction www.d.com
349
140.20
290.9
Mechanical Dimensions (WM343-SD330)
Chapter 1
349
140.20
290.9
Front View
Right View
Left View
Rear View
Mechanical Dimensions (WM343-SD331)
Front View
Right ViewLeft View
Rear View