dg casa 10450-6SET User manual

6 PIECE OUTDOOR FURNITURE
ASSEMBLY INSTRUCTIONS

WARNING
Seller and Manufacturer disclaim all and any liability for
property damage, personal injury, or loss, direct, indirect, or
incidental, resulting from the incorrect assembly, inadequate
maintenance, improper use, or neglect of this product.
Keep these assembly instructions for future reference.
Do not use this product if there are missing, damaged,
or broken parts until repairs are made and/or factory
replacement parts are installed.
Check all packing material carefully for small hardware
that may have become loose inside the carton
during shipment.
Identify and count all hardware and parts to compare with
parts and hardware list.
Follow assembly instructions closely. Improper assembly
can result in personal or property damage.
Secure all bolts before use.
Every 90 days check all bolts are secured.
Some parts may have a sharp corner or edge and may
be heavy.
Do not use or store this product near open flames or
around flammable chemicals.
When placing contents on non-carpeted flooring, it’s
recommended to use floor protection such as an area rug
or furniture pads. These are not included with the purchase.
NOTICE
TOOLS REQUIRED:
HEX WRENCH
(PROVIDED)

ARMCHAIR PARTS
FE Washer
x 14 x 14
A........Right Side ...............x 1
B........Left Side..................x 1
C........Back........................x 1
D........Seat ........................x 1
A
C
D
B
Bolt (M6 x 40mm)

ARMCHAIR ASSEMBLY - STEP 1
Attach Left Side (B) to Back (C) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
Washer
x 2 x 2
FBolt (M6 x 40mm)
C
B
FE

ARMCHAIR ASSEMBLY - STEP 2
Attach Seat (D) to Left Side (B) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
Washer
x 4 x 4
Bolt (M6 x 40mm)
D
B
FE

ARMCHAIR ASSEMBLY - STEP 3
Attach Seat (D) to Back (C) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
Washer
x 2 x 2
FBolt (M6 x 40mm)
C
D
FE

ARMCHAIR ASSEMBLY - STEP 4
Attach Right Side (A) to Back (C) and Seat (D) with Washer (E) and Bolt (F) as shown.
IMPORTANT: Fully tighten all bolts after this step is complete.
Washer
x 6 x 6
Bolt (M6 x 40mm)
A
C
D
FE

L CORNER PARTS
FWasher
x 12 x 12
Bolt (M6 x 40mm)
FE
B........Left Side..................x 1
G .......Back........................x 1
H........Seat ........................x 1
I .........Side Panel ..............x 1
B G
H
I

L CORNER ASSEMBLY - STEP 1
Attach Left Side (B) to Back (G) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
Washer
x 2 x 2
Bolt (M6 x 40mm)
FE
B
G

Attach Seat (H) to Left Side (B) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
L CORNER ASSEMBLY - STEP 2
Washer
x 4 x 4
Bolt (M6 x 40mm)
FE
H
B

Attach Seat (H) to Back (G) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
L CORNER ASSEMBLY - STEP 3
Washer
x 2 x 2
Bolt (M6 x 40mm)
FE
H
G

Attach Side Panel (I) to Seat (H) and Back (G) with Washer (E) and Bolt (F) as shown.
IMPORTANT: Fully tighten all bolts after this step is complete.
L CORNER ASSEMBLY - STEP 4
Washer
x 4 x 4
Bolt (M6 x 40mm)
FE
H
G
I

R CORNER PARTS
FWasher
x 12 x 12
Bolt (M6 x 40mm)
FE
A........Right Side ...............x 1
J ........Back........................x 1
K........Seat ........................x 1
I .........Side Panel ..............x 1
A
J
KK
I

R CORNER ASSEMBLY - STEP 1
Attach Right Side (A) to Back (J) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
Washer
x 2 x 2
Bolt (M6 x 40mm)
FE
A
J

Attach Seat (K) to Right Side (A) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
R CORNER ASSEMBLY - STEP 2
Washer
x 4 x 4
Bolt (M6 x 40mm)
FE
K
A

Attach Seat (K) to Back (J) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
R CORNER ASSEMBLY - STEP 3
Washer
x 2 x 2
Bolt (M6 x 40mm)
FE
K
J

Attach Side Panel (I) to Seat (K) and Back (J) with Washer (E) and Bolt (F) as shown.
IMPORTANT: Fully tighten all bolts after this step is complete.
R CORNER ASSEMBLY - STEP 4
Washer
x 4 x 4
Bolt (M6 x 40mm)
FE
J
K
I

CHAIR PARTS
FE Washer
x 10 x 10
L ........Back........................x 1
M .......Seat ........................x 1
I .........Side Panel ..............x 2
Bolt (M6 x 40mm)
L
M
I

CHAIR ASSEMBLY - STEP 1
Attach Seat (M) to Back (L) with Washer (E) and Bolt (F) as shown.
Note: Do not fully tighten any bolts until assembly is complete. Failure to follow
these instructions may cause the bolt holes to be misaligned during assembly.
Washer
x 2 x 2
FBolt (M6 x 40mm) FE
L
M

Attach Side Panels (I) to Seat (M) and Back (L) with Washer (E) and Bolt (F) as shown.
IMPORTANT: Fully tighten all bolts after this step is complete.
Washer
x 8 x 8
Bolt (M6 x 40mm)
FE
M
I
I
L
CHAIR ASSEMBLY - STEP 2