Courtyard Creations RTS422E User manual

ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
INTENDED FOR RESIDENTIAL USE ONLY.
PAGE 1 OF 7 COURTYARD CREATIONS INC.
RTS422E
Use the correct bolts as indicated. Do not tighten any of the bolts until the swing is
completely assembled.
Do not discard of any of the packaging until you have checked that you have all of the
parts and fittings required.
Keep children away during assembly. This item contains small parts that can be
swallowed by children. Children should always be under direct adult supervision while
using this product.
Retain these assembly instructions for future reference.
Quote the following FQC NO. when contacting the service center.
SERVICE CENTER TOLL FREE NO.
TEL: [phone]
FAX: [phone]
!
!
!
!
!
STOP DO NOT RETURN TO THE STORE!
V-3

A. Read instructions thoroughly. Acquaint yourself with the inventory of parts and
the accompanying drawings to ensure safe and proper assembly.
B. You will need the following tools
- Phillips Screwdriver
- Nut Wrench (See Part #30)
- Hex. Key Wrench (See Part #28 and #29)
C. Lay out all of the parts and identify them by using the table below.
PAGE 2 OF 7
PARTS LIST
PART
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1 17
16
18
19
20
21
22
23
24
25
27
28
29
30
31 1
1
1
2
2
4
2
4
1
2
2
2
1
2
2
2
2
1
RTS422E-CS09-8
17C01A0819071YX
17C40A0716001YX
18000615004
17C17A1306001YX
18000018001
17KAA0201----Y4
17KAB1101----Y4
61R422ED00001BA
BOLT M8*55
BOLT M6*45
SCREW ST4.2*16
PLASTIC SCREW
HEX. KEY WRENCH 6MM
NUT WRENCH 10 & 13MM
CANOPY
62RUS459FH102
62RUS422WI101
62RUS422WN101
62RUS422WN102
RTS422E-CS01-2
RTS422E-CS03-1
62RTS422EM102
62RUS4231I101
62RUS417SH102
17GA20405201-Y3
TOP CROSS BEAM W/ADJUSTABLE TEETH
REAR CROSS BRACE
LATERAL CROSS BRACE
FRONT UPRIGHT SUPPORT
REAR UPRIGHT SUPPORT
LEFT ARM
BACK ASSEMBLY
SWING ARM TUBE
FRONT/REAR CANOPY BRACE
U-SHAPED SIDE CANOPY BRACE
SUSPENSION SPRING
MATERIAL
CODE PART Q’TY
2
2
28000221024
28000221023
FRONT LEG CAP
REAR LEG CAP
32
2
17FA05050401-YX
WASHER d6.5*D16*1.2
17FA08060601-YX
WASHER d8.5*D17*1.6
14
18000C23001
PLASTIC NUT M6*P1.0
1
RTS422E-CS01-3
RIGHT ARM
26
1
17KAA0101----Y4
HEX. KEY WRENCH 4MM
CANOPY/FRAME CONNECTOR
2
17C40A0712001YX
BOLT M6*35
8
17C40A0714001YX
BOLT M6*40
4
17C40A0722001YX
BOLT M6*65
1
RTS422E-CS02-1
SEAT ASSEMBLY
2
62RTS422EM101
SWING ARM TUBE
STOP DO NOT RETURN TO THE STORE!
V-3

PAGE 3 OF 7
Fig. A
ASSEMBLY (Note: For all nuts and bolts
fastening, always use a washer (#23 or #24)
between the tube and bolt or the tube and
nut.)
Step 2:
Fasten the lateral cross braces (#3) to upright
supports (#4 and #5) by using bolts (#17),
washers (#24), and plastic nuts (#25). Repeat
the same procedure for both sides.
See Fig. A – Step 3.
Step 3:
Fasten the rear cross brace (#2) to the rear
upright supports (#5) by using bolts (#18),
washers (#24), and plastic nuts (#25). Tighten
all of the plastic nuts and bolts.
See Fig. A – Step 4.
Step 4:
Insert the front leg caps (#14) and the rear leg
caps (#15) into all of the base feet.
See Fig. A – Step 5.
Step 1
Step 2
Step 3
Step 4
Step 5
1
1
4
4
44
3
3
4
4
5
5
5
5
5
44
14
15
15
14
5
5
2
5
5
5
Step 1:
Insert the top cross beam w/adjustable teeth
(#1) into upright supports (#4 and #5), fasten
them by using bolts (#18), washers (#24), and
plastic nuts (#25). Repeat the same procedure
for both sides. Keep the bolts loose.
See Fig. A – Step 1 and Step 2.
18
17
18
24
24
25
24
24
25
18
24
24
24 25
24
25
STOP DO NOT RETURN TO THE STORE!
Do not tighten bolts
after Step 2. Fasten
all bolts after Fig A.
V-3

Step 6:
Open the seat assembly and fasten a swing
arm tube (#11) and the left arm (#6) to
the back assembly (#8) by using bolt (#19),
washers (#24). Repeat the same procedure
for both sides. Fasten another arm tube (#10)
to the left arm (#6) at the front bend by using
bolts (#18 and #19), washers (#24), and
plastic nut (#25). Repeat the same procedure
for both sides. Fasten the other end of the left
arm (#6) to the front of the seat assembly
(#9) by using bolt (#21) and washers (#23).
Repeat the same procedure for both sides.
Tighten all of the plastic nuts and bolts.
See Fig. C.
PAGE 4 OF 7
Step 7:
Hook the suspension spring (#16) into the
top of both swing arm tubes (#10 and #11).
Repeat the same procedure for both sides.
See Fig. D.
Fig. C
Fig. B
Fig. D
10
10
10 10
11
11
11
16
11
6
Step 5:
Fasten the back assembly (#8) to the seat
assembly (#9) by using bolts (#20), washers
(#24), and plastic nuts (#25). Tighten all of
the plastic nuts and bolts. See Fig. B.
8
8
6
7
9
9
16
Note:
The labels marked “L” and “R” on the arms
(#6 and #7) should coincide with Figure C to
ensure proper assembly.
L
R
STOP DO NOT RETURN TO THE STORE!
20
19
24
18 24
19 24
24 25
21
23
24
24
25
V-3

PAGE 5 OF 7
Fig. F
Step 1
Step 3
Step 2
Step 4
Step 5
Step 9:
Insert the U-shaped side canopy braces (#13)
into the canopy frame connectors (#26) and
secure with screws (#22). Please make sure
that the teeth of the canopy frame connectors
are facing towards the inside.
See Fig. F – Step 1 and Step 2.
Step 10:
Insert the front and rear canopy braces (#12)
into the sleeves on the canopy (#31).
See Fig. F – Step 3.
Step 11:
Insert the tube ends of the front and rear
canopy braces (#12) into the U-shaped side
canopy braces (#13). See Fig. F – Step 4.
Step 12:
Insert the corners of the U-shaped side canopy
braces (#13) into the pockets on the canopy
(#31). See Fig. F – Step 5.
13
13 13
12
12
12
12
13
31
31
31
26
22 22
Warning:
Make sure that both ends of the suspension
springs (#16) go completely through the
holes in the angled braces on the top cross
beam w/adjustable teeth (#1) and swing
arm tubes (#10 and #11).
Fig. E
16
16
16
16
1
Step 8:
Hang the other side of the suspension
spring (#16) into the hole located in
the angled brace on the top cross
beam w/adjustable teeth (#1).
Repeat the same procedure for
both sides. See Fig. E.
STOP DO NOT RETURN TO THE STORE!
V-3

Cleaning and Maintenance
• Wash frame and fabric parts with mild soap and water, rinse thoroughly, and dry completely. Do not use bleach,
acid, or other solvents on the frame or fabric parts.
• The canopy may be surface washed with mild soap and water if necessary. Commercial foaming upholstery
cleaner may also be used. Rinse well and hang to dry. Do not machine wash or dry.
• We recommend the use of furniture covers to protect your swing when not in use.
• Inspect and tighten all bolts and fasteners on a regular basis to ensure proper performance and safety of your
swing.
• In order to prolong the life and beauty of your swing, we recommend that the fabric parts be stored in a dry and
protected area during off season periods (i.e. overnight or on rainy days)
PAGE 6 OF 7
Note:
To avoid danger of suffocation, always keep
plastic bags and small parts away from
babies and children.
Fig. H
Step 13:
Fasten the canopy/frame connectors (#26) on
the canopy assembly to the adjustable teeth
on both sides of the top cross beam (#1) by
using plastic screws (#27). See Fig. G.
Fig. G
1
31
27 27
26 26
Warranty
•This product is covered by Courtyard Creations Inc.'s one–year limited warranty.
•Proof of purchase (dated register receipt) is required for warranty claims.
•It remains the customer’s responsibility for freight and packing charges to and from the service center.
STOP DO NOT RETURN TO THE STORE!
V-3

Special Warnings
• The user of this swing should always inspect it before each use.
• It is essential to place this swing on level ground and not less than 6 feet from any obstruction; such as fences,
garages, houses, overhanging branches, laundry lines, or electrical wires.
• Check the tightness of all of the nuts and bolts on a regular basis.
• Make sure that the suspension springs are properly secured before each use.
• Always remove the canopy in heavy wind conditions, otherwise the canopy may tip over and cause damage to
its parts.
• The manufacturer will not accept responsibility for unauthorized repairs or modifications to the swing or its parts.
• Oil all of the metal parts that move regularly.
• The weight limit is 750lbs.
PAGE 7 OF 7
STOP DO NOT RETURN TO THE STORE!
The store where you made your purchase
does not stock parts for this item.
If you need parts,
whether they are missing or damaged,
STOP!
Missing A Part?
No Need To Go Back To
The Store
Call us between 9:00 AM and 4:30 PM
Eastern Time Monday through Friday
For further assistance,
please visit us at
[email protected]
Call Toll Free:
TEL: [phone]
FAX: [phone]
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING ASSEMBLY
SEPARATE AND IDENTIFY ALL OF THE PARTS, MAKING SURE THAT
YOUHAVE ALL OF THEPARTSLISTED.
IF YOU DO NOTLOCATE ALL OF THE PARTS LISTED, INSPECT THE
PACKING MATERIAL FOR SMALL PARTSTHAT MAYHAVEBECOME
SEPARATED DURING SHIPMENT.
IF YOU EXPERIENCEANY DIFFICULTY DURING ASSEMBLYOR IF ANY
PARTS ARE MISSING OR DAMAGED,CALL THE HELP LINE AT
1-877-539-7436 BEFORERETURNING THIS ITEM TO THE STORE.
PROVIDE THEFOLLOWING INFORMATION WHEN CALLING:
1-MODEL NUMBER OF THEPRODUCT.
2-PARTNUMBER AND MATERIAL CODE OF THE PARTFROM THE PARTS
LIST.
MOST PROBLEMS CAN BERESOLVED WITHOUT RETURNING THIS
PRODUCT TO THERETAILER.
V-3

COURTYARD CREATIONS INC.
RTS422E
PÁGINA 1 DE 7
ATENCIÓN: ESTE PRODUCTO NO ES PARA USO COMERCIAL; ESTÁ
DISEÑADO ÚNICAMENTE PARA USO RESIDENCIAL.
INSTRUCCIONES DE ARMADO
Utilice los tornillos correctos, según se indica. No apriete ninguno de los tornillos hasta que el columpio
esté completamente ensamblado.
No tire el empaque hasta que haya comprobado que tiene todas las partes y los accesorios necesarios.
No deje que los niños se acerquen durante el ensamblado. Este producto contiene piezas pequeñas que
los niños pueden ingerir. Mientras usen este producto, los niños siempre deberán estar bajo la
supervisión directa de un adulto.
Conserve estas instrucciones para referencia futura.
Cuando se comunique con el centro de servicio, proporcione siempre el siguiente
código de control de calidad (FQC, por sus siglas en inglés).
NÚMERO GRATUITO DEL CENTRO DE SERVICIO
TEL: [phone]
FAX: [phone]
!
!
!
!
!
ALTO ¡NO DEVUELVA ESTE PRODUCTO A LA TIENDA!
V-3

A. Lea las instrucciones cuidadosamente. Familiarícese con el inventario de las
piezas y los dibujos que acompañan a asegurar el montaje seguro y correcto.
B. Necesitará las herramientas siguientes:
- Destornillador Phillips (no incluido)
- Llave para tuercas (Véase la parte #30)
- Llave hexagonal (Véase la parte #28 y #29)
C. Coloque todas las piezas en una superficie plana e identifíquelas utilizando
la tabla siguiente.
PARTS LIST
NO.DE
PARTE
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1 17
16
18
19
20
21
22
23
24
25
27
28
29
30
31 1
1
1
2
2
4
2
4
1
2
2
2
1
2
2
2
2
1
RTS422E-CS09-8
17C01A0819071YX
17C40A0716001YX
18000615004
17C17A1306001YX
18000018001
17KAA0201----Y4
17KAB1101----Y4
61R422ED00001BA
TORNILLO M8*55
TORNILLO M6*45
TORNILLO ST4.2*16
TORNILLO DE PLÁSTICO
LLAVE ALLEN DE 6MM
LLAVE DE TUERCAS DE 10 Y 13MM
TOLDO
62RUS459FH102
62RUS422WI101
62RUS422WN101
62RUS422WN102
RTS422E-CS01-2
RTS422E-CS03-1
62RTS422EM102
62RUS4231I101
62RUS417SH102
17GA20405201-Y3
BARRA TRANSVERSAL
SUPERIOR CON DIENTES AJUSTABLES
REFUERZO TRANSVERSAL
TRASERO
REFUERZO TRANSVERSAL LATERAL
SOPORTE VERTICAL DELANTERO
SOPORTE VERTICAL TRASERO
BRAZO IZQUIERDO
CONJUNTO
DE RESPALDO
TUBO DEL DESCANSABRAZOS
PARENTESIS DE TOLDO
DELANTERO/TRASERO
PARENTESIS
DE TOLDO LADO EN FORMA DE U
RESORTE DE SUSPENSIÓN
CÓDIGO DEL
MATERIAL PARTE CANT
-IDAD
2
2
28000221024
28000221023
TAPÓN DE PIERNA DELANTERO
TAPÓN DE PIERNA TRASERA
32
2
17FA05050401-YX
RONDANA d6.5*D16*1.2
17FA08060601-YX
RONDANA d8.5*D17*1.6
14
18000C23001
TUERCA DE PLÁSTICO M6*P1.0
1
RTS422E-CS01-3
BRAZO DERECHO
26
1
17KAA0101----Y4
LLAVE ALLEN DE 4MM
CONECTOR TOLDO-ARMAZÓN
2
17C40A0712001YX
TORNILLO M6*35
8
17C40A0714001YX
TORNILLO M6*40
4
17C40A0722001YX
TORNILLO M6*65
1
RTS422E-CS02-1
CONJUNTO DE ASIENTO
2
62RTS422EM101
TUBO DEL DESCANSABRAZOS
PÁGINA 2 DE 7
ALTO ¡NO DEVUELVA ESTE PRODUCTO A LA TIENDA!
V-3

Fig. A
ENSAMBLE (Nota: Para todos los pernos y
las tuercas de fijación, utilice siempre una
arandela (#23 o #24) entre el tubo y el perno
o el tubo y la tuerca.)
Paso 2:
Sujete los refuerzos transversales laterales (#3)
a los soportes verticales (#4 y #5) con ayuda de
los tornillos (#17), las rondanas (#24) y las
tuercas de plástico (#25). Repita el mismo
procedimiento para ambos lados.
Consulte la figura A, paso 3.
Paso 3:
Sujete el refuerzo transversal trasero (#2) a los
soportes verticales traseros (#5) con ayuda de
los tornillos (#18), las rondanas (#24) y las
tuercas de plástico (#25). Apriete todas las
tuercas y los tornillos.
Consulte la figura A, paso 4.
Paso 4:
Inserte las tapas de pierna delantera (#14) y
las tapas de pierna trasera (#15) en todos
pies de base. Consulte la figura A, paso 5.
Paso 1
Paso 2
Paso 3
Paso 4
Paso 5
1
1
4
4
44
3
3
4
4
5
5
5
5
5
44
14
15
15
14
5
5
2
5
5
5
Paso 1:
Inserte en el travesaño superior w/dientes
ajustable (#1) soportes verticales (#4 y #5),
les sujete mediante los pernos (#18), las
arandelas (#24) y las tuercas plásticas (#25).
Mantenga los pernos sueltos. Haga el mismo
procedimiento para ambas partes.
Consulte la figura A, paso 1 y paso 2.
18
17
18
24
24
25
24
24
25
18
24
24
24 25
24
25
PÁGINA 3 DE 7
No apriete los tornillos
después del paso 2, sino
hasta después de la figura A.
ALTO ¡NO DEVUELVA ESTE PRODUCTO A LA TIENDA!
V-3