DiaMedical DM100 User manual

Handheld Pulse Oximeter
Quick Reference Guide
DM100
On/O buon
2. Backlight Buon:
Press to turn the backlight on
for use in dim environments,
press again to turn o.
3. Alarm Silence Buon:
Turn o the audio alarm for 30,
60, 90 or 120 seconds. The
visual alarm will remain acve.
4. Up & Down Buons:
Choose opons within the
setup menu and adjust the
value of various parameters.
Backlight buon
Alarm silence buon
Up/Down buon
Funcon buon
• The DM100 Handheld Pulse Oximeter from DiaMedical
Diagnoscs features a large LCD display with SpO2 values and
waveforms along with pulse rate and real me clock
• Choose between large numeric or waveform modes for display
• Dual work modes for spot checks or dual monitoring
• Adjustable audio and visual alarms
• Review the latest ten (10) minutes of trending data with SpO2
and Pulse Rate table
• Powerful storage capacity for up to three hundred (300) hours
of paent data
• Data can be transferred to PC with PaentCare Viewer soware
for storage and review
• Automac power-o funcon for power saving
• Up to forty-eight (48) hours of use with one set of
four (4) AA baeries
• Oximeter comes with carrying case, standard
reusable DB9 adult sensor, user manual,
four (4) AA baeries and a two (2) year
manufacturer limited warranty
PRODUCT HIGHLIGHTS
1. Power Buon:
Press and hold for one second
to turn on; Press and hold for
two seconds to turn o.
1
5
4
3
2
5. Funcon Buon:
Press to select
opons within the
setup menu.
BUTTON FUNCTIONS

SCREEN ICONS
100% Measured SpO2% Data storage icon
PR Pulse rate display area Weak signal icon
60 BPM Measured Pulse rate
(BPM) 04: 59 Time in informaon area “hour: minute”
Indicates measured value
is higher than the high
alarm limit
ADU/NEO Paent type:
ADU or NEO
ID:99 Paent ID in
informaon area
Indicates measured value
is lower than the low alarm
limit
SpO2 waveform display Indicates sensor is o or is
not well t on the nger
Pulse amplitude display Sensor unconnected icon
Low baery icon Indicates the memory space
is full
Alarm silence icon Alarm system is o
SpO2SpO2 Display
•To install baeries: Press the baery compartment latch to remove the baery
access door. Place four (4) AA baeries inside using the + and - guides for orientaon.
•Use the System Setup Menu to select paent type: Adult, Pediatric or Neonatal.
•Default SpO2 low/high alarms are set for 90/100 for adults and 90/95 for neonates.
•Default pulse rate low/high alarms are set for 50/120 for adults
and 100/200 for neonates.
•Alarm and pulse tone volumes can be adjusted within a range from one to ve.
•To transfer data to a PC: Turn o the oximeter and push the Power and
Funcon buons at the same me for one second to start data transfer mode.
•To clean: Power o the oximeter and remove the baeries before cleaning with a cloth
that has been dampened with approved 75% ethanol or 70% isopropanol cleaning
soluon. Do not use ammonium disinfectants to prevent damaging the oximeter.
AVAILABLE ACCESSORIES
02.01.210122 Adult Reusable Silicone
So-Tip SpO2 Sensor
02.01.210121 Pediatric Reusable Silicone
So-Tip SpO2 Sensor
02.01.210673 Neonate Reusable Wrap
SpO2 Sensor
01.13.110504 SpO2 Extension Cable (DB9
to DB9)
03.16.113589 Rechargeable Ni-MH Baery
Kit with Charging Stand
TIPS FOR OPERATION
DiaMedical
31440 Northwestern Highway, Suite 150
Farmington Hills, MI 48334
P [phone] | F [phone] | [email protected]