DIAMOND DRYERS HD-D380BLK Service manual

Installation Manual
POWERFUL, BEAUTIFUL, TOUGH

Surface Mounted High Speed Hand Dryer
OPERATING INSTRUCTIONS AND PARTS MANUAL
TECHNICAL SPECIFICATIONS
Item Category Performance Date
Operating Voltage AC 220~240 V, 50/60 Hz, 380 W
Standby Power ≤0.5 W
Warm Air Speed Output 100 m/s
Motor Type Brushless DC Motor, 26,500 RPM
Sensor Type Auto Infrared touch free operation
Sensor Range 45° 5 ~ 12 mm
Timing Protection 30 seconds auto shut off
Drying Time 10 ~ 12 sec
Drip Proof IPX3
Isolation CLASS 1
Unit Size 272mm x 136mm x 123mm
IMPORTANT SAFETY INSTRUCTIONS
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS OBSERVE THE FOLLOWING:
• Use this unit only in the manner intended by the manufacturer. Manufacturer is
not responsible for damages caused by misuses or defective installations.
• The instructions contained within the installation Template enclosed must
be followed carefully when installing this unit. Failure to accurately follow
the instructions may result in the incorrect operation of this unit, damage to
property and/or personal injury.
• Installation work and electrical wiring must be done by qualified person(s)
in accordance with all applicable codes and standards, including fire-rated
construction.
• When cutting or drilling into wall or ceiling, do not damage electrical wiring and
other hidden utilities.
• This unit must be powered by a dedicated circuit branch protected by a
circuit breaker with the appropriate rating. Circuit cable must be fit current
consumption for this unit.
• This unit has been designed for indoor use only, protected from water, sun and
extreme temperatures, do not use it outdoors or close to moisture and heat
generators.
• This unit can only be revised, maintained, repaired and removed by qualified
person(s). If the unit stops and works strangely, contact your regional dealer or
contractor.
• This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Do not allow children to play with the appliance or carry out cleaning
and user maintenance on this hand dryer.
• If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
⚠

UNPACKING / STANDARD ACCESSORIES
1. Remove all packing material. Recycling is recommended.
2. Carefully remove the hand dryer from the shipping carton, using care not to
drop the appliance.
3. Use caution when removing the casing. The casing may have sharp edges/
corners which may cut or cause harm.
4. Inspect carefully for any damage that may have occurred during transit. Check
for any loose, missing or damaged parts. If the hand dryer is damaged, promptly
inform the shipper or dealer where you purchased it.
Standard items included with the hand dryer are:
INSTALLATION
CAUTION
• Make sure power supply breaker is switched off.
• All electrical installation and repair work should be carried out by a qualified
electrician or local service Engineer in accordance with current local codes or
regulations.
• Check that the electrical supply corresponds to that shown on the rating plate.
If the unit is connected to any electrical supply other than stated on the rating
plate of the unit, permanent damage or unsafe operation of the unit may result.
• The unit must be mounted on a flat vertical wall capable of supporting the full
weight of the unit.
• Do not use the backplate as a guide when drilling. Ensure no pipe work (gas,
water, air) or electrical cables, wires or ductwork are located directly behind the
drilling/mounting area.
1. UNPACKING
1.1 Place the main cover on a cloth to avoid
marking its surface.
1.2 Remove the (2) security screws from the
main body, using the service tool provided. Store
safely.
1.3 Lift the front cover off the main body.
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM

Recommended height measurements
from the floor to top screws ( 1).
Adult male 1300mm
Adult female 1265mm
Children 5-8 years old 928mm
Children 8-11 years old 1028mm
Children 11-14 years old 1108mm
Wheelchair user 1050mm
2. POSITIONING
2.1 Mark the location on the wall with a
pencil. Use the Backplate to mark the
locations for the four fixing points ( 2).
2.2. Pre-drill the wall in the marked
locations using a 5/16 (8mm) drill, inset
the plastic anchors and tap flush to the
wall ( 3).
2.3 Fix the backplate to the wall. Screw to
the wall and secure with the appropriate
fitting.
3. INSTALLING THE POWER
CABLE & CONNECTION
TERMINAL BLOCK
WARNING: ENSURE POWER IS NOT
CONNECTED
3.1 Pull the cable through the grommet.
Ensure the cable is long enough to route
correctly through the backplate to the
terminal block.
3.2 The cable must sit in the dedicated
channel.
3.3 As shown, connect cable to terminal
block ( 4).
3.4 Screw in terminal block.
3.5 Fix the cable clamp with screw in the
backplate.
CAUTION: Connect the ground wire to
the terminal block marked ‘ ’.
Do not over-tighten and crush the
power cable.
4. ATTACHING MAIN BODY
4.1 Close the main cover of the backplate
( 5).
4.2 Insert and tighten the (2) security
screws into the side of the main body
with the service tool as illustrated below.
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
4.3 Turn power on.
4.4 Test unit for correct operation.
CAUTION: Before installation decide if the cable entry is to be from the rear
or the above. Follow the relevant instructions. Do not use the backplate as a
guide when drilling.
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
1
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
2
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
3
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
4
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
5

OPERATION
1. No touch operation
2. Shake excess water from hands.
3. Place hands under the outlet to start operation.
4. Slowly move hands back and forth through the hand
dryer.
5. Start operation the blue LED lights.
6. Stop automatically after hands are removed.
If there is an electrical or motor problem a blue LED will blink when hands through
the hand dryer
MAINTENANCE
REGULAR MAINTENANCE
Regularly clean the outer casing use a soft, damp cloth to gently wipe away any dirt.
CAUTION: Never use abrasives or chemicals to clean the cover. Do not soak.
PERIODICAL DEEP CLEAN
Cleaning and maintenance must be performed by qualified electrical personnel.
1. Disconnect the electrical supply.
2. Use the service tool or security hex
driver to remove the two cover security
screws.
3. Remove the cover.
4. Clean all dust and lint from the interior
of the hand dryer.
5. Replace the cover.
6. Wipe the cover with a damp cloth.
CAUTION: Do not over tighten the screws.
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
Manual
Main Unit
Service Tool
Wall Mouting
anchors
Flat cable clamp
& Screw
Above
cable entry Grommet
L
N
6mm
High-Speed Hand Dryer
Installation Manual
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM
DIAMONDDRYERS.COM