Digi-Pas DWL-180 User manual

Product of Singapore
Screw-On (Module)
DIGITAL LEVEL
USER MANUAL
DWL-180 (0.05° Resolution)
This user manual is printed in small reading scale for paper saving
purpose to protect the environment.
For a better view of this user manual, please visit
http://www.digipas.com/catalog-manual to download the softcopy.
Digi-Pas®
DIGIPAS

Cleaning
• Keep the level dry and clean. Remove
any moisture or dirt with a soft, dry cloth.
• Do not use harsh chemicals, strong
detergents or cleaning solvents to clean
the level.
• Do not submerge device in water while
cleaning .Wiping or cleaning on device
surface is sufficient
Device Overview :
LCD Display
ON/OFF: Power on/o device
Alt.Zero :
- Set any angle to 0° as reference
- Press & Hold to turn on/o buzzer sound MODE SELECT :
- Press to change display unit
: °(Degree), %slope, mm/M, In/Ft
- Press & Hold to freeze Display value
CAL: Activate Calibration Mode
Sound Buzzer
Opening for screw

Technical Specification
Cleaning
• Keep the level dry and clean. Remove
any moisture or dirt with a soft, dry cloth.
• Do not use harsh chemicals, strong
detergents or cleaning solvents to clean
the level.
• Do not submerge device in water while
cleaning .Wiping or cleaning on device
surface is sufficient
Dimension : 117 x 48.5 x 16mm
Weight : 100 Grams
Operating Temp : 0° ~ +50°(Celsius)
Storage Temp : -10° ~ +60°(Celsius)
Battery : 2 x CR2032 (3V)

Battery Compartment
Push down the battery cover to slide open.
For the rst time usage, remove the plastic
strip to connect the battery

Caution
Digi-Pas device is calibrated in the factory for maximum
accuracy. User can re-calibrate when necessary.
Please refer to www.digipas.com for video demonstration
on how to calibrate the device.
®
Calibration Instruction
Note: Ensure the device is kept still during calibration
Clip the device to a spirit level, make sure the device is
securely cliped on the level, turn on the device then press
‘CAL’ button once the screen will display flashing “CAL1”.
Place the device on a flat and clean surface, press
“MODE” button once, the screen will display countdown,
wait until screen countdown reach “0” and show “CAL2”.
Rotate the device (180°) parallel to the surface then press
“MODE” button again, the screen will display countdown,
wait until screen countdown reach “0” and show “CAL3”.
Position the device vertically (-90°) on a level surface,
press “MODE” button again, the screen will display
countdown, wait until screen countdown reach “0” and
show “CAL4”.
Rotate the device 180° parallel vertically to the surface
(+90°) then press “MODE” button again, the screen will
display countdown, wait until screen countdown reach “0”.
Calibration Done.
1.
2. a
b
c
d
3.

Calibration Illustration

Warranty
Digi-Pas® Digital level is warranted to the original purchaser to
be free from defects in workmanship and material. JSB Tech will,
at its option, repair or replace any detective part which may
malfunction under normal and proper use within a warranty
period of 1 (one) year from the date of shipment. This one year
warranty clause is NOT applicable to European Union (EU)
member states. Purchases made in EU member states will be
covered by the existing consumer laws across the European
Union, which provide statutory warranty rights in addition to the
coverage of one year warranty period. The foregoing warranty
shall not apply to defects resulting from misuse, abuse or transfer
by the Buyer, Buyer-supplied software or interfacing,
unauthorized modification or operation outside of environmental
specifications for the product. JSB Tech does not warrant that the
operation of the instrument software, or firmware, will be
uninterrupted or error free.
The exclusive remedy under any and all warrants and
guarantees, expressed herein, and we shall not be liable for
damages from loss or delay of equipments uses, consequential,
or incidental damage. No other warranty is expressed or implied.
JSB Tech specifically disclaims the implied warranties of
merchantability and fitness for a particular purpose.
Limitation of Liability
In no event shall DIGIPAS TECHNOLOGIES INC., (hereinafter,
“the Company”) be liable to you or any third party for any indirect,
special, incidental, exemplary or consequential damages of any
kind resulting from any breach of warranty or from the
performance or use of the product. This includes without
limitation: property damage, loss of value of the product or any
third party products that are used with the product, or loss of use
of the product or any third party products that are used with the
product, even if the Company has been advised of the possibility
of such loss or damages. The Company’s total cumulative liability
arising from or related to the product, whether in contract, tort
(including negligence) or otherwise, shall not exceed the amount
actually paid by you for the product. Some states and/or
jurisdictions do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions
may not apply to you. If any limitation of liability shall be deemed
invalid by any applicable law, then the limitations of liability set
forth above shall apply to the maximum extent permitted under
applicable law.

Manufactured by
JSB TECH Pte Ltd
Email: [email protected]
www.digipas.com
Distributed by :