Stanley CL2XTi User manual

Please read these instructions before operating the product
CL2XTi
2 - Beam Self-Leveling Cross Line Laser
77-121
Self-Leveling
GB
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
TR
LT
HR

277-121
Carefully read the Safety Instructions and User Manual before using this product. The person
responsible for the instrument must ensure that all users understand and adhere to these
instructions.
Retain this manual for future reference.
IMPORTANT: The following labels are on your laser tool for your convenience and safety.
They indicate where the laser light is emitted by the level. ALWAYS BE AWARE of their
location when using the level.
1. Safety
2. Product Description
3. Specifications
4. Operating Instructions
5. Calibration
6. Maintenance and Care
7. Warranty
User Safety
Safety
Contents
EN 60825-1
LASER RADIATION - DO NOT
STARE INTO BEAM OR VIEW
DIRECTLY WITH
OPTICAL INSTRUMENTS
CLASS 1M LASER PRODUCT
MAX OUTPUT ≤ 1 mW @ 630 - 670 nm
GB
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
GB
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
TR
GB
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
GB ENGLISH
GERMAN
FRENCH
ITALIAN
SPANISH
PORTUGUESE
DUTCH
DANISH
SWEDISH
FINNISH
NORWEGIAN
POLISH
GREEK
CZECH
RUSSIAN
HUNGARIAN
SLOVAKIAN
SLOVENIAN
BULGARIAN
ROMANIAN
ESTONIAN
LATVIAN
LITHUANIAN
TURKISH
CROATIAN
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
LT LT LT LT
TR TR TR
HR HR HR HR

3
77-121
DO NOT remove any warning label(s) on the housing. This instrument must only be used for
leveling and layout tasks as outlined in this manual.
ALWAYS make sure that any bystanders in the vicinity of use are made aware of the
dangers of looking directly into the laser tool.
DO NOT use in combination with other optical instruments. Do not modify the instrument, or
make manipulations or use in other applications than those described in the manual.
DO NOT look into the beam with optical aids, such as magnifiers, binoculars or Telescopes.
DO NOT stare into the laser beam or direct it towards other persons. Make sure the
instrument is not set at eye level. Eye protection is normally afforded by natural aversion
responses such as the blink reflex.
DO NOT direct the laser beam at other persons.
ALWAYS turn the laser tool “OFF” when not in use. Leaving the laser tool “ON” increases
the risk of someone inadvertently staring into the laser beam.
DO NOT operate the laser tool in combustible areas such as in the presence of flammable
liquids, gases or dust.
DO NOT disassemble the laser tool. There are no user serviceable parts inside.
Disassembling the laser will void all warranties on the product. Do not modify the product in
any way. Modifying the laser tool may result in hazardous laser radiation exposure.
DO NOT use this instrument in areas where a risk of explosion is present.
NOTE: Since the laser beam is of the focused type, ensure you check the beam’s path over
a relatively long distance and take all necessary precautions to ensure the beam cannot
interfere with other persons.

477-121
WARNING: Batteries can explode or leak and can cause injury or fire. To reduce this risk:
ALWAYS follow all instructions and warnings on the battery label and package.
DO NOT short any battery terminals
DO NOT charge alkaline batteries.
DO NOT mix old and new batteries. Replace all of them at the same time with new batteries
of the same brand and type.
DO NOT mix battery chemistries.
DO NOT dispose of batteries in fire.
ALWAYS keep batteries out of reach of children.
ALWAYS remove batteries if the device will not be used for several months.
NOTE: Ensure that the correct batteries as recommended are used.
NOTE: Ensure the batteries are inserted in the correct manner, with the correct polarity.
DO NOT dispose of this product with household waste.
ALWAYS dispose of batteries per local code.
PLEASE RECYCLE in line with local provisions for the collection and disposal of electrical
and electronic waste under the WEEE Directive.
Battery Safety
End of Life

5
77-121
ROHS Compliant
The Stanley Works declares that the CE Mark has been applied to this
product in accordance with the CE Marking Directive 93/68/EEC.
This product conforms with EN60825-1:2007.
For further details please refer to www.stanleyworks.com.
Declaration of Conformity
Product Description
Package Contents
1. Laser Unit
2. Universal Mount Adapter
3. L-Type Bracket
4. Pole Clamp (attaches to L-Type Bracket)
5. Laser Target
6. Telescopic Pole
7. Carrying Case
8. Batteries (3 x AA)
9. User Manual
EN 60825-1

677-121
1
6
2
3
5
4
1
2
5
4
6
Product Overview
1. Window for Cross Beam Laser
2. Main Power / Transport Lock
3. Keyboard
4. Laser Warning Label
5. Battery Compartment Cover
Laser Unit
6. 1/4 - 20 Threaded Mount
3
Universal Mount Adapter
1. 1/4 - 20 Screw Mount
2. Magnet Mount
3. 5/8 - 11 Threaded Mount
4. Fold Out Legs for Tripod
5. Tightening Knobs
6. 1/4 - 20 to 5/8 - 11 Screw Mount Adapter

7
77-121
L-Type Bracket
Pole Clamp
1. Keyhole Slots
2. 1/4 - 20 Screw Mount
1. Clamp
2. 3 Pin Key
2
1
1
2
2
1. Spring Tension End with Snap on Plate
2. Multi-Segment Telescopic Pole (Can be used
independently or with the included foldable
tripod legs to make it free standing)
Telescopic Pole
1

877-121
Leveling Accuracy:
Horizontal / Vertical Accurracy
Working Range:
Working Distance:
with Laser Detector:
Laser Class:
Laser Wavelength:
Operating Time:
Power Voltage:
Power Supply:
IP Rating:
Operating Temperature Range:
Storage Temperature Range:
Weight (without Base and Batteries):
Size:
≤ 3 mm / 10 m (≤ 1/8 in / 30 ft)
≤ 3 mm / 10 m (≤ 1/8 in / 30 ft)
Self-Leveling to ± 4°
≤ 15 m (≤ 50 ft)
≤ 50 m (≤ 165 ft)
Class 1M
635 nm ± 5 nm
12 h
4,5 V
3 x AA Batteries (Alkaline)
IP54
-10° C to +40° C (+14° F to +104° F)
-20° C to +60° C (-4° F to +140° F)
230 g (8 oz)
88 mm × 48 mm × 90 mm (3 1/2 in × 1 7/8 in × 3 1/2 in)
Specifications
Laser Unit

9
77-121
Operating Instructions
1. Turn laser unit to back. Open battery
compartment cover by bending tab out to
unlock.
Lift Out
+++
---
Laser Unit
2. Install / Remove batteries. Orient batteries
correctly when placing into laser unit.
3. Close and lock battery compartment
cover. Be sure tab snaps back into locking
feature.
Battery Installation / Removal

10 77-121
Laser Mode
3. Press laser mode key to toggle through
available laser modes - horizontal only,
vertical only, both horizontal and vertical,
self-leveling disabled, laser OFF.
2. Transport lock in unlocked position. Laser
power is ON. Right LED indicator lights green
when laser unit has self-leveled.
4. Mode 4 disables self-leveling feature and
allows both the horizontal and vertical
beams to be positioned in any orientation.
Right LED indicator lights red.
5. Press pulse mode key to toggle between
pulse mode ON and OFF. Left LED lights blue
when pulse mode on. Pulse mode allows use
with a laser detector.
OFF / Locked
Unlocked
1. Transport lock in locked position. Laser
power is OFF.
Pulse Mode
6. Laser beam(s) turn off and right LED lights
red to indicate the laser unit is out of
the working range for laser modes 1 - 3.
Reposition laser unit to be more level.
Function

11
77-121
7. Laser beam(s) will dim when battery power
is low. Replace batteries.
1. 1/4 - 20 screw mount to attach laser unit.
Allows for full 360° placement of the laser
unit.
Universal Mount Adapter
360° Placement
3. 5/8 - 11 thread mount available for optional
accessories. Thread mount adapter stored on
unit. 1/4-20 inside thread, 5/8 - 11 outside
thread.
4. Attach to supportive magnetic objects with
the built in magnets.
5. Angles can be set and locked in both axis.
2. Can be used as a miniature tripod using the
fold out legs.
5/8 in
Standard Mount for
Optional Tripod Mounting
Tightening
Knobs

12 77-121
L-Type Bracket and Pole Clamp
1. 1/4 - 20 screw mount to attach laser unit.
Allows for full 360° placement of the laser
unit.
360° Placement
2. Fasten pole clamp to L-type bracket to allow
use with tripod or other optional accessories.

13
77-121
Applications
3. Square:
Using both the vertical and horizontal laser
beams, establish a point where the vertical
and horizontal beams cross. Position the
desired object(s) until they are aligned with
both the vertical and horizontal laser beams
to ensure object(s) are square.
1. Plumb:
Using the vertical laser beam, establish a
vertical reference plane. Position the desired
object(s) until they are aligned with the
vertical reference plane to ensure object(s)
are plumb.
2. Level:
Using the horizontal laser beam, establish
a horizontal reference plane. Position the
desired object(s) until they are aligned with
the horizontal reference plane to ensure
object(s) are level.
4. Pulse Mode:
Setting laser unit to pulse mode allows use
of optional laser detectors.
5. Manual Mode:
Disables self-leveling function and allows
laser unit to project a rigid laser beam in any
orientation.

14 77-121
Calibration
NOTE: The laser unit has been calibrated at the time of manufacturing. Periodically check
the accuracy of the laser unit to ensure that the calibrated specifications are maintained.
1. Place laser unit as shown with laser ON.
Mark point P1 at cross.
Level Beam Accuracy
2. Rotate laser unit 180° and mark point P2
at cross.
3. Move laser unit close to wall and mark
point P3 at cross.
4. Rotate laser unit 180° and mark point P4
at cross.
P1
D1
D1
2
P2
P1
D1
D1
2
P3
P1
P2
D2
P4
P1
P2
P3
D2

15
77-121
5. Measure the vertical distance from
the floor to each point. Calculate the
difference between distances DP1 and DP3
to get D3 and distances DP2 and DP4 to get
D4 .
1. Place laser unit as shown with laser
ON. Aim vertical beam to first corner or
reference point. Measure out half of the
distance D1 and mark point P1 .
Horizontal Beam Accuracy
P1
D1
D1
2
D1
2
6. Calculate the maximum allowed offset
distance and compare to the difference
of D3 and D4 as shown in the equation. If
the sum is not less than or equal to the
calculated maximum offset distance the
unit must be returned to your Stanley
Distributor.
Example: D1 = 10 m, D2 = 0,5 m
DP1 = 30,75 mm, DP2 = 29 mm, DP3 = 30 mm, DP4 = 29,75 mm
D3 = (30,75 mm - 30 mm) = 0,75 mm
D4 = (29 mm - 29,75 mm) = - 0,75 mm
0,3 x (10 m - (2 x 0,5 m) = 2,7 mm (maximum allowed offset distance)
(0,75 mm) - (- 0,75 mm) = 1,5 mm
1,5 mm ≤ 2,7 mm (TRUE, unit is within calibration)
mm
m
P3
P1
DP3
DP1
(DP1 - DP3 ) = D3P4
P2
DP2
DP4
(DP2 - DP4 ) = D4
Compare:
D3 - D4 ≤ ± Max
Maximum Offset Distance:
Max in
ft
= 0,0036 x (D1 ft - (2 x D2 ft))
mm
m
= 0,3 x (D1 m - (2 x D2 m))

16 77-121
P1
D2
12
P1
D1
D1
2
D1
2
2. Rotate laser unit to other corner or
reference point.
3. Measure the vertical distances between
P1 and the horizontal beam from the 2nd
location.
4. Calculate the maximum allowed offset
distance and compare to D2 . If D2 is
not less than or equal to the calculated
maximum offset distance the unit must be
returned to your Stanley Distributor.
Example: D1 = 5 m, D2 = 1 mm
0,3 x 5 m = 1,5 mm (maximum allowed offset distance)
1 mm ≤ 1,5 mm (TRUE, unit is within calibration)
mm
m
Compare:
D2 ≤ Max
Maximum Offset Distance:
Max in
ft
= 0,0036 x D1 ft
mm
m
= 0,3 x D1 m

17
77-121
Vertical Beam Accuracy
P1
D1P2P3
D1
2 x D1
P4
D1
P2P3
D1
2 x D1
P1
P1
D2
1. Measure the height of a door jamb or
reference point to get distance D1 . Place
laser unit as shown with laser ON. Aim
vertical beam towards door jamb or
reference point. Mark points P1 , P2 , and
P3 as shown.
2. Move laser unit to opposite side of door
jamb or reference point and align vertical
beam with P2 and P3 .
3. Measure the horizontal distances between
P1 and the vertical beam from the 2nd
location.
4. Calculate the maximum allowed offset
distance and compare to D2 . If D2 is
not less than or equal to the calculated
maximum offset distance the unit must be
returned to your Stanley Distributor.
Example: D1 = 2 m, D2 = 0,5 mm
0,6 x 2 m = 1,2 mm (maximum allowed offset distance)
0,5 mm ≤ 1,2 mm (TRUE, unit is within calibration)
mm
m
Compare:
D2 ≤ Max
Maximum Offset Distance:
Max in
ft
= 0,0072 x D1 ft
mm
m
= 0,6 x D1 m

18 77-121
Laser unit is not waterproof. DO NOT allow to get wet. Damage to internal circuits may
result.
DO NOT leave laser unit in direct sunlight or expose it to high temperatures. The housing
and some internal parts are made of plastic and may become deformed at high temperatures.
DO NOT store the laser unit in a cold environment. Moisture may form on interior parts
when warming up. This moisture could fog up laser windows and cause corrosion of internal
circuit boards.
When working in dusty locations, some dirt may collect on the laser window. Remove any
moisture or dirt with a soft, dry cloth.
DO NOT use aggressive cleaning agents or solvents.
Store the laser unit in its case when not in use. If storing for extended time, remove batteries
before storage to prevent possible damage to the instrument.
Maintenance and Care

19
77-121
One Year Warranty
Stanley Tools warrants its electronic measuring tools against deficiencies in materials and/or
workmanship for one year from date of purchase.
Deficient products will be repaired or replaced, at Stanley Tools’ option, if sent together with
proof of purchase to:
Stanley UK Sales Limited
Gowerton Road
Brackmills, Northampton NN4 7BW
This Warranty does not cover deficiencies caused by accidental damage, wear and tear, use
other than in accordance with the manufacturer’s instructions or repair or alteration of this
product not authorised by Stanley Tools.
Repair or replacement under this Warranty does not affect the expiry date of the Warranty.
To the extent permitted by law, Stanley Tools shall not be liable under this Warranty for
indirect or consequential loss resulting from deficiencies in this product.
This Warranty may not be varied without the authorisation of Stanley Tools.
This Warranty does not affect the statutory rights of consumer purchasers of this product.
This Warranty shall be governed by and construed in accordance with the laws of England
and Stanley Tools and the purchaser each irrevocably agrees to submit to the exclusive
jurisdiction of the courts of England over any claim or matter arising under or in connection
with this Warranty.
IMPORTANT NOTE: The customer is responsible for the correct use and care of the
instrument. Moreover, the customer is completely responsible for periodically checking the
accuracy of the laser unit, and therefore for the calibration of the instrument.
Calibration and care are not covered by warranty.
Subject to change without notice
Warranty

20 77-121
Lesen Sie vor der Verwendung dieses Produkts aufmerksam die Sicherheitshinweise und die
Bedienungsanleitung. Die für das Instrument verantwortliche Person muss gewährleisten,
dass sämtliche Benutzer die darin enthaltenen Anweisungen verstehen und befolgen.
Heben Sie diese Bedienungsanleitung auf.
WICHTIG: Die folgenden Etiketten auf Ihrem Lasergerät erleichtern Ihnen die Arbeit und
dienen Ihrer Sicherheit. Sie zeigen an, wo Laserlicht ausgestrahlt wird. Wenn Sie die
Nivellierung benutzen, sollten Sie STETS ihre Position KENNEN.
1. Sicherheit
2. Produktbeschreibung
3. Technische Daten
4. Betriebsanleitung
5. Kalibrierung
6. Wartung und Pflege
7. Gewährleistung
Benutzersicherheit
Sicherheit
Inhaltsverzeichnis
EN 60825-1
LASERSTRAHLUNG - NICHT
IN DEN STRAHL SEHEN ODER
DIREKT MIT OPTISCHEN
INSTRUMENTEN BETRACHTEN
LASERPRODUKT DER KLASSE 1M
MAXIMALE LEISTUNG ≤ 1 mW @ 630 - 670 nm
GB
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
GB
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
TR
GB
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
GB ENGLISH
GERMAN
FRENCH
ITALIAN
SPANISH
PORTUGUESE
DUTCH
DANISH
SWEDISH
FINNISH
NORWEGIAN
POLISH
GREEK
CZECH
RUSSIAN
HUNGARIAN
SLOVAKIAN
SLOVENIAN
BULGARIAN
ROMANIAN
ESTONIAN
LATVIAN
LITHUANIAN
TURKISH
CROATIAN
D
F
I
E
PT
NL
DK
SE
FIN
NO
PL
GR
CZ
RU
HU
SK
SI
BG
RO
EE
LV
LT LT LT LT
TR TR TR
HR HR HR HR