digi-tech GNX4 User manual

WARNING FOR YOUR PROTECTION
PLEASE READTHE FOLLOWING:
KEEPTHESE INSTRUCTIONS
HEEDALLWARNINGS
FOLLOW ALL INSTRUCTIONS
DO NOT USETHISAPPARATUS NEARWATER
CLEAN ONLYWITH A DRY CLOTH.
DO NOT BLOCKANY OFTHEVENTILATION OPENINGS.INSTALL
IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUC-
TIONS.
DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIA-
TORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS
(INCLUDINGAMPLIFIERS)THAT PRODUCE HEAT.
ONLY USEATTACHMENTS/ACCESSORIES SPECIFIED BYTHE MAN-
UFACTURER.
UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR
WHEN UNUSED FOR LONG PERIODS OFTIME.
Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding type plug has two blades and a third grounding prong. The
wide blade or third prong are provided for your safety.If the provided
plug does not fit your outlet,consult an electrician for replacement of
the obsolete outlet.
Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
Use only with the cart stand, tripod bracket, or table specified by the
manufacture,or sold with the apparatus. When a cart is used,use cau-
tion when moving the cart/apparatus combination to avoid injury from
tip-over.
Refer all servicing to to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged,liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain
or moisture,does not operate normally, or has been dropped.
POWER ON/OFF SWITCH: For products provided with a power
switch,the power switch DOES NOT break the connection from the
mains.
MAINS DISCONNECT: The plug shall remain readily operable. For
rack-mount or installation where plug is not accessible, an all-pole
mains switch with a contact separation of at least 3 mm in each pole
shall be incorporated into the electrical installation of the rack or build-
ing.
FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE
RECEPTACLE: Replace fuse with same type and rating only.
MULTIPLE-INPUTVOLTAGE:This equipment may require the use of a
different line cord,attachment plug, or both, depending on the available
power source at installation.Connect this equipment only to the power
source indicated on the equipment rear panel.To reduce the risk of fire
or electric shock, refer servicing to qualified service personnel or
equivalent.
This Equipment is intended for rack mount use only.
SAFETY INSTRUCTIONS
NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED
WITHA POWER CORD.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The cores in the mains lead are coloured in accordance with
the following code:
GREEN andYELLOW - Earth BLUE - Neutral BROWN - Live
As colours of the cores in the mains lead of this appliance may
not correspond with the coloured markings identifying the ter-
minals in your plug,proceed as follows:
•The core which is coloured green and yellow must be
connected to the terminal in the plug marked with the
letter E,or with the earth symbol, or coloured green,or
green and yellow.
•The core which is coloured blue must be connected to
the terminal marked N or coloured black.
•The core which is coloured brown must be connected to
the terminal marked L or coloured red.
This equipment may require the use of a different line cord,
attachment plug, or both, depending on the available power
source at installation. If the attachment plug needs to be
changed, refer servicing to qualified service personnel who
should refer to the table below. The green/yellow wire shall be
connected directly to the units chassis.
WARNING:If the ground is defeated,certain fault conditions in
the unit or in the system to which it is connected can result in
full line voltage between chassis and earth ground. Severe injury
or death can then result if the chassis and earth ground are
touched simultaneously.
LIVE
ENEUTRAL EARTH GND
CONDUCTOR
L
NBROWN BLUE
GREEN/YEL
BLACK
Normal Alt
WIRE COLOR
WHITE
GREEN
The symbols shown above are internationally accepted
symbols that warn of potential hazards with electrical
products. The lightning flash with arrowpoint in an equi-
lateral triangle means that there are dangerous voltages
present within the unit. The exclamation point in an equi-
lateral triangle indicates that it is necessary for the user to
refer to the owner’s manual.
These symbols warn that there are no user serviceable
parts inside the unit. Do not open the unit. Do not
attempt to service the unit yourself. Refer all servicing to
qualified personnel. Opening the chassis for any reason
will void the manufacturer’s warranty. Do not get the unit
wet. If liquid is spilled on the unit, shut it off immediately
and take it to a dealer for service. Disconnect the unit
during storms to prevent damage.
IMPORTANT SAFETY INSTRUCTIONS

U.K. MAINS PLUG WARNING
A molded mains plug that has been cut off from the cord is unsafe. Discard
the mains plug at a suitable disposal facility. NEVER UNDERANY CIRCUM-
STANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG
INTOA 13 AMP POWER SOCKET. Do not use the mains plug without the
fuse cover in place. Replacement fuse covers can be obtained from your local
retailer. Replacement fuses are 13 amps and MUST be ASTA approved to
BS1362.
LITHIUM BATTERYWARNING
CAUTION!
This product may contain a lithium battery.There is dan-
ger of explosion if the battery is incorrectly replaced.
Replace only with an Eveready CR 2032 or equivalent.
Make sure the battery is installed with the correct polari-
ty. Discard used batteries according to manufacturer’s
instructions.
ADVARSEL!
Lithiumbatteri - Eksplosjonsfare.Ved utskifting benyttes
kun batteri som anbefalt av apparatfabrikanten. Brukt bat-
teri returneres apparatleverandøren.
ADVARSEL!
Lithiumbatteri - Eksplosionsfare ved fejlagtig håndtering.
Udskiftning måkun ske med batteri av samme fabrikat og
type. Levér det brugte batteri tilbage til leverandøren.
VAROITUS!
Paristo voi räjähtää,jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppin.Hävitäkäytetty paristo valmistajan ohjeiden
mukaisesti.
VARNING!
Explosionsfara vid felaktigt batteribyte.Använd samma bat-
terityp eller en ekvivalent typ som rekommenderas av
apparattillverkaren.Kassera använt batteri enligt fabrikan-
tens instruktion.
IMPORTANT SAFETY INSTRUCTIONS
ELECTROMAGNETIC
COMPATIBILITY
This unit conforms to the Product
Specifications noted on the Declaration
of Conformity. Operation is subject to
the following two conditions:
•this device may not cause harmful
interference,and
•this device must accept any interfer-
ence received, including interference
that may cause undesired operation.
Operation of this unit within significant
electromagnetic fields should be avoided.
•use only shielded interconnecting
cables.
Manufacturer’s Name: DigiTech
Manufacturer’sAddress: 8760 S.Sandy Parkway
Sandy,Utah 84070,USA
declares that the product:
Product name: GNX4
Note:Product name may be suffixed by the letters EU,JA, NP
and UK.
Product option: all (requires Class II power
adapter that conforms to the
requirements of EN60065,
EN60742,or equivalent.)
conforms to the following Product Specifications:
Safety: IEC 60065 (1998)
EMC: EN 55013 (1990)
EN 55020 (1991)
Supplementary Information:
The product herewith complies with the requirements of the
LowVoltage Directive 72/23/EEC and the EMC Directive
89/336/EEC as amended by Directive 93/68/EEC.
Vice-President of Engineering
8760 S.Sandy Parkway
Sandy,Utah 84070,USA
Date:March 15,2004
European Contact: Your local DigiTech Sales and
Service Office or
Harman Music Group
8760 South Sandy Parkway
Sandy,Utah 84070 USA
Ph:[phone]
Fax:[phone]
DECLARATION OF
CONFORMITY

Warranty
We at DigiTech are very proud of our products and back-up each one we sell with the following warranty:
1.The warranty registration card must be mailed within ten days after purchase date to validate this
warranty.
2.DigiTech warrants this product, when used solely within the U.S.,to be free from defects in materials and
workmanship under normal use and service.
3.DigiTech liability under this warranty is limited to repairing or replacing defective materials that show
evidence of defect, provided the product is returned to DigiTechWITH RETURN AUTHORIZATION,
where all parts and labor will be covered up to a period of one year.A ReturnAuthorization number may
be obtained from DigiTech by telephone.The company shall not be liable for any consequential damage as
a result of the product's use in any circuit or assembly.
4.Proof-of-purchase is considered to be the burden of the consumer.
5.DigiTech reserves the right to make changes in design,or make additions to, or improvements upon this
product without incurring any obligation to install the same on products previously manufactured.
6.The consumer forfeits the benefits of this warranty if the product's main assembly is opened and
tampered with by anyone other than a certified DigiTech technician or,if the product is used withAC
voltages outside of the range suggested by the
manufacturer.
7.The foregoing is in lieu of all other warranties,expressed or implied,and DigiTech neither assumes nor
authorizes any person to assume any obligation or liability in connection with the sale of this product. In
no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in
the performance of this warranty due to causes beyond their control.
NOTE: The information contained in this manual is subject to change at any time without
notification. Some information contained in this manual may also be inaccurate due to
undocumented changes in the product or operating system since this version of the manual
was completed.The information contained in this version of the owner's manual supersedes all
previous versions.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Included Items . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Make Connections . . . . . . . . . . . . . . . . . . . . . . . .2
Speaker Compensation . . . . . . . . . . . . . . . . . . . .2
Apply Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Select an Output Setup Mode . . . . . . . . . . . . . . .2
Select a Preset . . . . . . . . . . . . . . . . . . . . . . . . . . .2
A GuidedTour of the GNX4 . . . . . . . . . . . . . . . . .3
The Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . .3
The Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . .6
Audio Routing Setups . . . . . . . . . . . . . . . . . . . .9
Setups Introduction . . . . . . . . . . . . . . . . . . . . . . . . .9
Output Setups and Speaker Compensation . . . . .9
Mic and Line Setups . . . . . . . . . . . . . . . . . . . . . . .12
Optimizing the Mic Input Level . . . . . . . . . . . . . .13
Optimizing the Line Input Levels . . . . . . . . . . . . .13
Making Connections . . . . . . . . . . . . . . . . . . . . .14
For Live Performance . . . . . . . . . . . . . . . . . . . . . . .14
Small Club Setup (MonoAmp Rig) . . . . . . . . . . . .14
Medium Stage Setup (StereoAmp Rig) . . . . . . . .14
Large Stage Setup (StereoAmp/Cabinet Rig) . . . .15
Talker™Performance Setup . . . . . . . . . . . . . . . . . .16
Coffee House/Solo Performance Setup . . . . . . . .17
For Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Onboard Recorder Application . . . . . . . . . . . . . .18
Computer RecordingApplication . . . . . . . . . . . . .19
Applying Power . . . . . . . . . . . . . . . . . . . . . . . . . . .20
About the GNX4 . . . . . . . . . . . . . . . . . . . . . . . .21
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Footswitch Modes . . . . . . . . . . . . . . . . . . . . . . . . . .21
Preset Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Preset Bounceback . . . . . . . . . . . . . . . . . . . . . .22
Stompbox/Control Mode . . . . . . . . . . . . . . . . . . .22
Recorder Mode . . . . . . . . . . . . . . . . . . . . . . . . . .22
Expression Pedal . . . . . . . . . . . . . . . . . . . . . . . . . .22
Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Tuner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
GNX4 Matrix Functions . . . . . . . . . . . . . . . . . .24
The GNX4 Matrix . . . . . . . . . . . . . . . . . . . . . . . . .24
Viewing/Editing GeNetX™and
Amp ParameterValues . . . . . . . . . . . . . . . . . . . . . .24
Viewing/Editing Effect ParameterValues . . . . . . . . . .25
GENETX Row . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
CHAN ONE EQ and CHANTWO EQ Rows . . . .27
TONE Row . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Amp/Cabinet Modeling . . . . . . . . . . . . . . . . . . .30
Amp Models . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
CabinetTypes . . . . . . . . . . . . . . . . . . . . . . . . . . .31
EditingAmp Models and CabinetTypes . . . . . . . . . .31
SelectingAmp Models and CabinetTypes . . . . . . .32
AdjustingAmp Parameters . . . . . . . . . . . . . . . . . .32
CabinetTuning . . . . . . . . . . . . . . . . . . . . . . . . . . .32
StoringAmp Parameter Edits . . . . . . . . . . . . . . . .33
Creating HyperModels™. . . . . . . . . . . . . . . . . . . . .33
Saving HyperModels (Amp Save) . . . . . . . . . . . . . . .33
Effects and Parameters . . . . . . . . . . . . . . . . . . .34
Editing a Preset’s Effects . . . . . . . . . . . . . . . . . . . . .34
Effect Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Preset Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Wah-Pickup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Whammy™/IPS/Talk . . . . . . . . . . . . . . . . . . . . . . .36
Whammy . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Intelligent Pitch Shifting (IPS) . . . . . . . . . . . . . .37
Detune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Pitch Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Talker™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Stomp Box Modeling . . . . . . . . . . . . . . . . . . . . . .38
Noise Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Chorus/Mod Effects . . . . . . . . . . . . . . . . . . . . . . .39
Chorus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Flanger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Phaser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Triggered Flanger . . . . . . . . . . . . . . . . . . . . . . .40
Triggered Phaser . . . . . . . . . . . . . . . . . . . . . . . .40
Tremolo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Panner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Vibrato . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Rotary Speaker . . . . . . . . . . . . . . . . . . . . . . . . .41
AutoYa™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
YaYa™. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
SynthTalk™. . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Envelope Filter . . . . . . . . . . . . . . . . . . . . . . . . .42
Detune . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Pitch Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
Reverb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Expression Pedal Assignment . . . . . . . . . . . . . .45
Expression Pedal . . . . . . . . . . . . . . . . . . . . . . . . .45
Expression Pedal Links 1-3 . . . . . . . . . . . . . . . . . .45
Wah Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Amp Channel Footswitch . . . . . . . . . . . . . . . . . .46
Control Footswitches . . . . . . . . . . . . . . . . . . . . .46
ControlA, B,and C Links . . . . . . . . . . . . . . . . . .46
LFOs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
LFO Links 1-2 . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Expression ParameterAssignment List . . . . . . . . .48
Whammy™/IPS/Talker™Effect Parameters . . . . .48
Stompbox Effect Parameters . . . . . . . . . . . . . .48
Modulation Effects Parameters . . . . . . . . . . . . .49
Creating a Preset . . . . . . . . . . . . . . . . . . . . . . .50
Selecting a Preset . . . . . . . . . . . . . . . . . . . . . . . . . .50
Create a HyperModel™. . . . . . . . . . . . . . . . . . . . . .50
Select the Channel 1Amp and Cabinet . . . . . . . .50
Select the Channel 2Amp and Cabinet . . . . . . . .50
Adjust the Channel 1 Parameters . . . . . . . . . . . .51
Adjust the Channel 2 Parameters . . . . . . . . . . . .51
Adjust the EQ/Tune the Cabinets . . . . . . . . . . . .52
WarpingAmp ChannelsTogether . . . . . . . . . . . . .53
Table of Contents

Save the HyperModel™. . . . . . . . . . . . . . . . . . . . .53
Select Models for the Preset’s Channels . . . . . . .54
Edit the Presets Effects . . . . . . . . . . . . . . . . . . . .54
Select the PickupType . . . . . . . . . . . . . . . . . . .55
Turn the Compressor Off . . . . . . . . . . . . . . . .55
Turn theWhammy™/IPS/Talker™Off . . . . . . . . .55
Turn the Stompbox Modeling Off . . . . . . . . . . .55
Adjust the Noise Gate . . . . . . . . . . . . . . . . . . .56
Select andAdjust the Chorus . . . . . . . . . . . . .56
Turn the Delay Off . . . . . . . . . . . . . . . . . . . . . .56
Select andAdjust the Reverb . . . . . . . . . . . . . .57
Store the Preset . . . . . . . . . . . . . . . . . . . . . . . . .57
Storing/Copying a Preset . . . . . . . . . . . . . . . . . .58
Storing a Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Copying a Preset . . . . . . . . . . . . . . . . . . . . . . . . . . .58
Footswitch Functions for Modes . . . . . . . . . . . .59
Preset Mode - Green . . . . . . . . . . . . . . . . . . . . . . .59
Stompbox/Control Mode -Yellow . . . . . . . . . . . . . .60
Recorder Mode - Red . . . . . . . . . . . . . . . . . . . . . . .61
Drum Machine/MP3 Player . . . . . . . . . . . . . . . .62
Control Panel - Drum Machine/MP3
Player Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Stop/Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Pattern/File . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Internal Drum Pattern List . . . . . . . . . . . . . . . .62
Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Tempo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62
Internal Drum Kit List . . . . . . . . . . . . . . . . . . .62
Footswitch Operation . . . . . . . . . . . . . . . . . . . . . . .63
GNX4 MP3 Demo (Internal) . . . . . . . . . . . . . . . . . .63
Audio Routing for Recording . . . . . . . . . . . . . .64
GNX4 Inputs and Recorder Routing . . . . . . . . . . . .64
GNX4 Input Sources . . . . . . . . . . . . . . . . . . . . . . .64
(Compact Flash) CF/USB 1-2 Source . . . . . . . . . .64
USB 3-4 Source . . . . . . . . . . . . . . . . . . . . . . . . . .65
Guitar Signal Routing . . . . . . . . . . . . . . . . . . . . . .66
Mic Signal Routing . . . . . . . . . . . . . . . . . . . . . . . .66
Line Signal Routing . . . . . . . . . . . . . . . . . . . . . . . .67
The GNX4’s 8-Track Recorder . . . . . . . . . . . . .68
Recorder Control and
USB/Signal Routing Panel . . . . . . . . . . . . . . . . . . . . .68
Song Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .70
Drums/MP3 (Pattern/File) . . . . . . . . . . . . . . . . . .70
Drums/MP3 Level . . . . . . . . . . . . . . . . . . . . . . . .70
Song Tempo . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71
Drum Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
ClickTrack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
Pre-Roll . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Song Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73
Auto Stop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Quantize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
Using Compact Flash Memory Cards . . . . . . . . . . .75
Let’s Start Recording! . . . . . . . . . . . . . . . . . . . . . . .76
Selecting an Input Source . . . . . . . . . . . . . . . . . . .76
Using the Record and Playback Meters . . . . . . . . .76
Using the GNX4’s Recorder Panel for Recording . . .77
Recording aTrack . . . . . . . . . . . . . . . . . . . . . . . .77
Playing Back a RecordedTrack . . . . . . . . . . . . . . .78
Recording MultipleTracks . . . . . . . . . . . . . . . . . .78
SettingTrack Playback Levels and Panning . . . . . .78
Setting EachTrack’s Playback Level: . . . . . . . . . .79
Setting EachTrack’s Pan: . . . . . . . . . . . . . . . . . .79
Adjusting the Recorder’s Playback
Master Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Undoing/Erasing aTrack . . . . . . . . . . . . . . . . . . . .80
Using UndoWhile the Recorder is Stopped . . .80
Using UndoWhile Recording is in Progress . . .80
ChangingTrack Status . . . . . . . . . . . . . . . . . . . . .81
Punching In / Punching Out . . . . . . . . . . . . . . . . .81
Bouncing/MergingTracks . . . . . . . . . . . . . . . . . . .81
Re-Amping Using the GNX4’s Recorder . . . . . . . . .82
Hands-Free Recording . . . . . . . . . . . . . . . . . . . . . . .83
Using the RECORD Footswitch
to Record aTrack . . . . . . . . . . . . . . . . . . . . . . . . .83
Using the PLAY Footswitch to
Play Back a RecordedTrack . . . . . . . . . . . . . . . . . .83
Using the Footswitches to
Record MultipleTracks . . . . . . . . . . . . . . . . . . . . .83
Using the UNDO Footswitch
to Erase aTrack . . . . . . . . . . . . . . . . . . . . . . . . . .84
Using UndoWhile the Recorder is Stopped . . .84
Using UndoWhile Recording is in Progress . . .84
Using the Footswitches for
Punching In/Punch Outing . . . . . . . . . . . . . . . . . . .84
Hands-Free Recording with the GNXFC . . . . . . . . .85
Using the GNXFC to Record aTrack . . . . . . . . .85
Using the GNXFC to Play Back
a RecordedTrack . . . . . . . . . . . . . . . . . . . . . . . . .85
Using the GNXFC to Record
MultipleTracks . . . . . . . . . . . . . . . . . . . . . . . . . . .85
Using the GNXFC to Undo/Erase aTrack . . . . . .86
Using UndoWhile the Recorder is Stopped . . .86
Using UndoWhile Recording is in Progress . . .86
Using the GNXFC for
Punching In/Punching Out . . . . . . . . . . . . . . . . . .86
Using the GNX4’s JamMan™Delay Looper . . . . . . . .87
Recording a Loop . . . . . . . . . . . . . . . . . . . . . . .87
Recording Layered Overdubs toYour Loop . . .88
Using Quantize for Seamless Loops . . . . . . . . . .88
Using the GNXFC for Looping . . . . . . . . . . . . . . . .89
Recording a Loop . . . . . . . . . . . . . . . . . . . . . . . .89
Recording Layered Overdubs toYour Loop . . . . .89
Drum Machine Recorder Operation . . . . . . . . . . . .90
Setting Up Playback Files with a Song . . . . . . . . .90
Recording Drums . . . . . . . . . . . . . . . . . . . . . . . .90
MIDI and Recording . . . . . . . . . . . . . . . . . . . . . . . . .91
Working with Songs and Loops . . . . . . . . . . . . . . . .91
Selecting Songs and Loops . . . . . . . . . . . . . . . .91
Deleting Songs and Loops . . . . . . . . . . . . . . . . .91
Table of Contents

Computer Recording via USB . . . . . . . . . . . . . .92
USB Recording Introduction . . . . . . . . . . . . . . . . . .92
Installing the GNX4’s Software Suite . . . . . . . . . .92
Connecting the GNX4 to the Computer . . . . . .92
Using ProTracks Plus™. . . . . . . . . . . . . . . . . . . . . .93
Installing ProTracks Software . . . . . . . . . . . . . . . .93
Setting Up the GNX4 MIDI Device . . . . . . . . . . .93
Setting up the GNX4 for Hands-Free Recording .93
Setting up ProTracks Plus™for GNX4Audio . . . .94
Using the GNX4’s Footswitches for
Hands-Free Computer Recording . . . . . . . . . . . . . .95
Recording aTrack orTracks . . . . . . . . . . . . . . . . .95
Playing Back a RecordedTrack . . . . . . . . . . . . . . .95
Recording MultipleTracks . . . . . . . . . . . . . . . . . .95
Using the UNDO Footswitch to Erase aTrack . .96
Using the GNXFC for Hands-free Computer
Recorder Functions . . . . . . . . . . . . . . . . . . . . . . . . .96
Re-Amping a GuitarTrack . . . . . . . . . . . . . . . . . . . .97
GNX4 Drums and MIDI . . . . . . . . . . . . . . . . . . . . .98
Recording the GNX4 Drums asAudio . . . . . . . . .98
Recording the GNX4 Drums as MIDI . . . . . . . . . .98
USB Playback Mix . . . . . . . . . . . . . . . . . . . . . . . . . .99
USB 1-2 Level/USB 3-4 Level . . . . . . . . . . . . . . . . . .99
Using BIAS®Deck™SE . . . . . . . . . . . . . . . . . . . . . . .100
Configuring theAudio Settings
for BIAS Deck SE . . . . . . . . . . . . . . . . . . . . . . . . .100
Compact Flash File Functions . . . . . . . . . . . . . .101
Compact Flash File Structure . . . . . . . . . . . . . . . . . .101
Songs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
MP3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .101
Compact Flash Storage/FileTransfer . . . . . . . . . . . . .102
Windows®Users . . . . . . . . . . . . . . . . . . . . . . . . . .102
Mac®Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
Memory Card/Computer File Format . . . . . . . . . . .103
Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
Volume Pedal Update . . . . . . . . . . . . . . . . . . . . . . .104
V-SwitchThreshold/Sensitivity . . . . . . . . . . . . . . . . .104
Expression Pedal Calibration . . . . . . . . . . . . . . . . . .104
Preset Bounceback . . . . . . . . . . . . . . . . . . . . . . . . .105
Hands-Free Default . . . . . . . . . . . . . . . . . . . . . . . . .105
Bank Names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .105
MIDI Channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Bulk Dump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
MIDI Preset Dump . . . . . . . . . . . . . . . . . . . . . . . . .106
User HyperModel™Amp Dump . . . . . . . . . . . . . . .106
MIDI Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
MIDI Merge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Drum MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .107
Default Drum Kit . . . . . . . . . . . . . . . . . . . . . . . . . .108
Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Trouble Shooting Guide . . . . . . . . . . . . . . . . . .109
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Preset List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
MIDI Implementation Chart . . . . . . . . . . . . . . . . . .112
MIDI CC List . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113
General MIDI Drum Sample List . . . . . . . . . . . . . . .114
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
Table of Contents

Introduction
Congratulations on your purchase of the GNX4 GuitarWorkstation™. The GNX4 is the most advanced
product of its kind, delivering an award-winning GeNetX™multi-modeling guitar processor, onboard 8-track
digital recorder,General MIDI drum machine,MP3 player,and USB audio/MIDI interface in a single integrated
package. Combined with the included suite of recording, editing, and production software, the GNX4 Guitar
Workstation is a complete solution for your performing and recording needs.
The intuitive user interface makes programming as simple as turning a knob. However, your time would be
well spent by reading through this Owner’s Manual with your GNX4 in front of you.
Included Items
Please check to make sure the following items have been included:
• DigiTech GNX4 GuitarWorkstation
• DigiTech PSS3 Power Supply
• DigiTech GNX4 Owner’s Manual
• DigiTechWarranty Card
• ProTracks Plus™User’s Guide
• ProTracks Plus™Quick Start Guide
• Lexicon®Pantheon™User’s Guide
• DigiTech GNX4 Software Suite Package
••X-Edit™Editor/Librarian and USB Drivers CD
••ProTracks Plus™Software CD (Windows®XP/2000)
••BIAS®Deck™SE Software CD (Mac®OSX)
••GNX4 Software Installation Guide
• USB Cable
The utmost care was taken in the manufacturing and packaging your GNX4. Everything should be included
and in perfect working condition. However,if you find anything missing,please contact the factory at once.
Please take a moment to fill out the warranty card.It is your safeguard in the unlikely event that the GNX4
develops a problem.
1
Introduction

Quick Start
This Quick Start section is included for those of you who would rather play now and read later.
Make Connections
1.Connect your instrument to the GUITAR/INSTRUMENT INPUT jack on the GNX4’s rear panel.
2.Connect either the 1/4” or the XLR LEFT/RIGHT OUTPUTS to the input(s) of your amplifier(s),
power amp,or mixer.
Speaker Compensation
The GNX4 is equipped with SPEAKER COMPENSATION filtering that can be used with its 1/4”,
XLR,and HEADPHONE OUTPUTS.
1.If you are using the GNX4 with headphones or connecting it directly to a mixer via the XLR
OUTPUTS, switch the XLR OUTPUTS’ SPEAKER COMPENSATION on. The switch is
located to the right of the XLR jacks on the rear panel.
2.If you are connecting the GNX4 directly to a guitar amplifier with a built-in speaker via the 1/4”
OUTPUTS,switch the 1/4” OUTPUTS’ SPEAKER COMPENSATION off. The switch is
located to the right of the 1/4”jacks on the rear panel.
Apply Power
1.Turn the OUTPUT level knobs (for both the 1/4” and XLR OUTPUTS), on the rear panel of the
GNX4, all the way down (fully counter clockwise).
2.Connect the PSS3 power supply to the POWER jack on the GNX4.
3.Connect the other end of the PSS3 power supply to anAC outlet.
4.Turn the GNX4 POWER switch on.
5.Turn your amplifier(s) on,and adjust the volume(s) to a normal playing level. Gradually turn up the
GNX4’s OUTPUT level.
Select an Output Setup Mode
1.Press the OUTPUT SETUP button located in the control panel to the right of the DATAWHEEL.
2.Rotate the DATA WHEEL to select an Output Setup mode.
3.Select the Output Setup mode that applies to your application, they include: SteroAll,Mono All,
Mono 1/4,Mono XLR,Split 1 and Split 2.
Note: See page 9 for a detailed explanation of the Output Setups.
5.Press the EXIT button located in the control panel.
Select a Preset
The GNX4 comes with 80 pre-programmed Factory Presets,and 80 User Presets. From the factory,the
User Presets are exact duplicates of the Factory Presets.
1.Press the UP/DOWN footswitches to select a Bank.
2.Press Footswitches 1-5 to select a preset,or rotate the DATAWHEEL.
2
Introduction

A GuidedTour of the GNX4
The Front Panel
1. Footswitches 1-5
Depending on the selected mode, these 5 footswitches select presets,change amp channels,turn
individual effects on and off,control drum machine operations,control playback of MP3 files,and give you
hands-free operation of the GNX4’s onboard recorder. Drums/MP3, Bypass,Tuner, Mode, and Pattern/File
functions are accessed by pressing the labeled pair of footswitches.
2. Recorder Control and USB/Signal Routing Panel
This control panel operates the GNX4’s onboard digital recorder,USB audio routing,and mass storage
functions. (See page 68 for more details regarding the Recorder Control and USB/Signal Routing
Panel.)
3. Record/Play Level Meters
These 4 Segment LED Meters allow you to monitor the Record/Play signal levels during use.
4. Effect Select Buttons
The Effect Select buttons are used together with the Matrix LEDs to choose the effects you want to edit.
5.Amp Control Buttons
TheAmp Control buttons are used to select one of the amp/cabinet model edit rows including:
CHAN ONE EQ (Green),GENETX (Yellow), CHANTWO EQ (Red), andTONE (Silver)
6. Status Button
The Status button is used to select amp channels for editing purposes and to turn each respective amp
channel’s EQ on and off. With the CHAN ONE EQ (Green) amp/cabinet model edit row selected, the
Status button turns Channel One’s EQ on and off. With the GENETX (Yellow) amp/cabinet model edit
row selected, the Status button selects between the Channel One, ChannelTwo,and theWarp Channels
(if aWarped state between both channels exists). With the CHANTWO EQ (Red) amp/cabinet model 3
Introduction
CONTROL A CONTROL B CONTROL C
TAP TEMPOAMP CHANNEL
1
37 98111213
14 15
564
2 10
ab

edit row selected, the Status button turns ChannelTwo’s EQ on and off. With theTONE (Silver) edit row
selected,the Status button selects between Channel OneAmp,WarpedAmp, and ChannelTwoAmp. The
Amp Gain,Bass,Midrange,Treble, and Amp Levels alternate between editing Channel One’s (lit green) or
ChannelTwo’s (lit red) amp settings as the status button is pressed. When editing effects in the Effect
Matrix,the Status Button turns the selected effect on and off,or selects a controller type for the
expression assignment.
7. Knobs
Depending on which amp control row or effect row is selected using the Amp Control or Effect
Select buttons,these 5 knobs adjust the parameters listed in the column directly above or below each
knob.
8. Matrix
a. GeNetX™Amp Controls Matrix
The GeNetXAmp Controls Matrix displays the GNX4’s Channel One and ChannelTwo amp types,
cabinet types,EQ/tone controls, and cabinet tuning parameters available for editing in each preset.
b. Effects Matrix
The Effects Matrix displays the effects parameters available for editing in each preset.
9. Displays
The Displays give feedback of the various functions that are being used in the GNX4,including preset
name, editing functions, tuner,utility menus,drum machine and recorder settings.
10. Preset Bank LEDs
The Preset Bank LEDs indicate whether the selected preset is an internal Factory or User preset,or if
the preset is a user preset saved externally on the optional Compact Flash memory card.
11. DataWheel
The DataWheel is a multi-function control used for selecting presets,editing preset parameters or for
adjusting the settings of the Recorder, Drum Machine,Utility,and Output Setup menus.
12. Status Indicator LEDs (+48V,V-Switch, and USB Active)
The Status Indicator LEDs illuminate when the Microphone Input has +48V Phantom Power active,the
Expression Pedal’s V-Switch is engaged,or the USB connection is active.
13. Control Panel Buttons
The Control Panel Buttons are used to select the GNX4’s Footswitch Modes, Output Setups, Utility
functions,and to storeAmp/Cabinet Model edits and Preset changes. They also access the GNX4’s
onboard General MIDI Drum Machine and MP3 Player. The buttons are labeled as follows:
MODE -This button changes the functionality of footswitches 1-5 (see the Footswitch Functions
for Modes section on page 59). When the Mode button is lit yellow, footswitches 1-5
toggle effects on and off,change amp channels, or can be assigned to various parameters
using the control footswitches. When the Mode button is lit green,footswitches 1-5 select
presets in the current preset bank. When the Mode button is lit red, footswitches 1-5
control the GNX4’s recorder functions.
4
Introduction

OUTPUT SETUP -This button selects one of the GNX4 Output Setups: StereoAll, Mono All,
Mono 1/4”,Mono XLR,Split 1 and Split 2. Stereo and MonoAll have all the
input sources (guitar,mic, line,drums,onboard recorder playback and audio
playback from USB) routed to both output pairs in either stereo or mono
respectively. Split 1 routes the guitar signal to just the 1/4”outputs while all
other sources are routed out the XLR outputs. Split 2 is the same as Split 1
but the guitar signal is also routed out the XLR outputs.
UTILITY -This button accesses the GNX4’s global functions including:Volume Pedal Update,
V-SwitchThreshold/Sensitivity,Expression Pedal Calibration,Preset Bounceback,Hands-
Free,Bank Naming,MIDI Channel selection,Sysex Bulk Dump,MIDI Preset Dump,User
HyperModel™Amp Dump, MIDI Mapping,MIDI Merge,Drum MIDI, Default Drum Kit, and
Factory Reset (see the Utilities section on page 104).
AMP SAVE -This button stores Amp and Cabinet changes (tone, gain, level, amp type, cabinet type,
warp, or cabinet tuning) as HyperModels.
STORE -This button is used to save Preset edits to the GNX4’s User Presets or to an optional
Compact Flash card.
(STOP/PLAY) -This button is used to turn the GNX4’s General MIDI Drum Machine/MP3
Player on and off.
PATTERN/FILE - Pressing this button and using the DATAWHEEL selects the GNX4’s internal
drum patterns,external MIDI,or MP3 files to be played. MIDI and MP3 files must
be resident in the GNX4>MIDI and GNX>MP3 directories on your Compact
Flash card in order for them to be recognized (see the Memory
Card/Computer File Format section on page 103).
LEVEL -This button adjusts the GNX4’s Drum Machine output level or the playback level of MP3s.
TEMPO -This button adjusts the tempo of the GNX4’s Drum Machine. Tempo is ignored when an
MP3 is selected.
KIT -This button selects one of the GNX4’s drum kits. Kit is ignored when an MP3 is selected.
EXIT - Exits all functions back to the preset display.
14. Down/Up Footswitches
These footswitches select songs (Recorder Mode), move up and down through the User preset banks
(Preset Mode),and navigate through presets (Stompbox/Control Mode). Pressing and holding these
footswitches simultaneously temporarily enables them to select the GNX4’s drum patterns or any MIDI
and MP3 files available on an optional Compact Flash memory card.
15. Expression Pedal
The Expression Pedal controls effect parameters in real time. Most GNX4 parameters can be assigned to
the Expression Pedal. Applying extra pressure to the toe of the Expression Pedal enables theV-Switch
feature which changes the Expression Pedal’s function to control theWah (see V-Switch
Threshold/Sensitivity on page 104).
5
Introduction

The Rear Panel
1. Guitar/Instrument Input
Connect your guitar/instrument to this jack.
2. Mic Level
Controls the gain of the mic input preamp.
3. Microphone Input
Connect a low impedance microphone to this jack for recording vocals or acoustic instruments into the
GNX4’s Recorder. It can also be used for theTalker™Vocoder effect (see Talker on page 37). The mic
signal can remain dry or processed through the GNX4’s effects for live and recording applications.
4. -20dB Pad Switch
The -20dB pad is a resistive attenuator that drops the level coming from the mic input jack. Its purpose
is to give you a way of preventing overload of the preamp when incoming signals become excessive.
When the pad is on,the net gain of the preamp is 20dB lower than normal.
5. +48V Phantom Power Switch
This switches on the phantom power to the Microphone Input. Dynamic microphones do not require
phantom power to operate,but are not harmed by it. Most condenser microphones do require phantom
power to operate. If you are unsure about the phantom power requirements for your microphone,
consult your microphone’s documentation or contact the manufacturer.
6. Left/Right Balanced Line Inputs
Connect line level sources to these jacks for recording or live performance mixing into the GNX4. Line
signals can remain dry or be processed through the GNX4’s effects for live and recording applications.
7. Output Level (1/4”Outputs Only)
Controls the overall volume level of the 1/4”outputs of the GNX4.
8. Left/Right Line 1/4”Balanced Outputs
Connect these outputs to your guitar amplifier(s),power amplifier(s), or to a mixing console that accepts
1/4”balanced connections.
9. Speaker Compensation Switch (1/4”Outputs Only)
This switch enables Speaker Compensation on the 1/4”Outputs for when they are connected to a
full-range speaker system. This switch should be set to the off position when the 1/4”outputs are
connected to a guitar amp or power amp/guitar cabinet system.
10. Output Level (XLR and Headphone Outputs Only)
Controls the overall volume level of the balanced XLR and Headphone outputs of the GNX4.
12345 6 7 981011121314151617182019
6
Introduction

11. Left/Right XLR Balanced Outputs
Connect these outputs to your power amplifier/speaker system or to a mixing console that accepts XLR
balanced connections.
12. Speaker Compensation Switch (XLR and Headphone Outputs Only)
This switch enables Speaker Compensation on the XLR and Headphone Outputs for when they are
connected to a full-range speaker system. This switch should be set to the off position when the XLR
outputs are connected to a power amp/guitar cabinet system.
13. Ground Lift Switch
This switch lifts pin 1 of the XLR Outputs from all ground references. This may be necessary to break
troublesome ground loops that can cause hum in the system,especially when both XLR and 1/4”outputs
are used together.
14. Headphone Output
Connect a pair of stereo headphones to this jack. Do not connect a mono plug to this jack, as it may
damage the output driver.
15. Footswitch
(Optional ) Connect a GNXFC footswitch to this jack for remote control of the GNX4’s recorder
functions.
16. USB Jack
Connect this jack to your computer’s USB port for hard disk recording and computer preset editing via
the X-Edit™Editor/Librarian software. A standard USB cable is included. The GNX4 is compatible with
USB 2.0 high speed ports, however the USB 2.0 bus will switch to a USB v1.1 full speed data rate to
work with the GNX4.
ATTENTION: Before using the GNX4’s USB connection,it is necessary to first install
the USB drivers provided on the X-Edit Software CD. Please read the Software
Installation Guide that came with your GNX4 for the proper instructions on how to
install the drivers for your operating system.
17. MIDI In
The MIDI In jack receives all incoming MIDI data. MIDI preset changes and CC control messages
received from external MIDI devices connected to the MIDI In jack can be used to control the GNX4
and its presets parameters. When the GNX4 is connected to the computer via USB,the MIDI In can be
used as a MIDI interface for recording any MIDI data in ProTracks Plus™or other MIDI recording
software.
18. MIDI Out/Thru
The MIDI Out/Thru jack sends MIDI data from the GNX4 including system exclusive information and
MIDI preset changes. When the GNX4 is connected to the computer via USB,it can act as a MIDI
interface for sending MIDI data from ProTracks Plus™or other MIDI recording software to external
keyboards or sound modules. When MIDI Merge is enabled in the Utility menu,the MIDI Out acts as a
MIDIThru for any data coming into the GNX4 from the MIDI In jack.
19. Power Switch
Turns the power on and off.
7
Introduction

20. Power Input
Connect only the provided DigiTech PSS3 power supply to this jack.
21. Compact Flash Memory Card Slot
(Optional ) Insert an optional Compact Flash (CF) card in this slot for use with the GNX4’s on board
recorder. Songs,Presets,MIDI files,and MP3 files can be saved and retrieved from the CF card as well.
The GNX4 can also function as a Compact Flash card reader by using a Compact Flash card (inserted
into this slot) and connecting the GNX4 to your computer via the USB port. The Compact Flash card
will be recognized as a hard disk (mass storage drive) for transferring files. See Compact Flash
Storage/FileTransfer on page 102 for more information regarding this function.
NOTE: The GNX4 is compatible withType I Compact Flash cards only. It is not compatible
withType II cards or IBM/Hitachi Microdrives™.
8
Introduction

Setups Introduction
The GNX4 is equipped with four inputs and four outputs that can be configured several different ways for
both live and recording applications. These settings determine which pair of outputs the mic,line, and guitar
processing are routed to and how the mic or line inputs are routed through the GNX4’s effects
processing.
Output Setups and Speaker Compensation
The GNX4 features both 1/4”and XLR outputs on the rear panel. These jacks let you simultaneously
connect the GNX4 to an amplifier/speaker system on stage via the 1/4”outputs and connect directly to
your PA system via the XLR outputs. The GNX4 incorporates Speaker Compensation filtering that can
be turned on or off independently for each output pair depending on your application needs.
Use the OUTPUT SETUP button along with the DATAWHEEL to select one of the Output Setup
options.
The six Output Setups are as follows:
steroall -All input sources (guitar, mic,line, drums, onboard 8-track recorder playback and USB
playback) are routed to both output pairs in stereo. Speaker Compensation can be turned
on and off independently for either the 1/4" or XLR outputs using the Speaker
Compensation switch associated with each pair on the rear panel.
Mic Input
Guitar Input
Line Left
Line Right
mic rvb mic dry
line rvb line dry
DRUMS,
RECORDER,
USB PLAYBACK
SC
mic fx
line fx
= Speaker Compensation Module
Delay Reverb
++
XLR Left Output
XLR Right Output
1/4" Left Output
1/4" Right Output
++
+SC
SC
SC
SC
Pickup
Sim Wah Comp Stompbox CH 1
Cabinet
Comp
Detector Gate Detector
Whammy/IPS
(except
Talker)
CH 1Amp
Modeling/
Tone
CH 1
Cabinet
CH 1Amp
Modeling/
Tone
CH 2
Cabinet
CH 2Amp
Modeling/
Tone
Gate Whammy/IPS
(Talker) Chorus/
Mod
+
+
Output Setup button
Control Panel
DataWheel
9
Audio Routing Setups

mono all - All input sources (guitar, mic, line,drums,onboard 8-track recorder playback and USB
playback) are routed to both output pairs in mono. Speaker Compensation can be turned
on and off independently for either the 1/4" or XLR outputs using the Speaker
Compensation switch associated with each pair on the rear panel.
mono 1/4 - All input sources (guitar, mic, line,drums,onboard 8-track recorder playback and USB
playback) are routed to the 1/4”outputs in mono. All input sources routed to the XLR
outputs maintain stereo separation. Speaker Compensation can be turned on and off
independently for either the 1/4" or XLR outputs using the Speaker Compensation switch
associated with each pair on the rear panel.
mono xlr - All input sources (guitar, mic, line,drums,onboard 8-track recorder playback and USB
playback) are routed to the XLR outputs in mono. All input sources routed to the 1/4”
outputs maintain stereo separation. Speaker Compensation can be turned on and off
independently for either the 1/4" or XLR outputs using the Speaker Compensation switch
associated with each pair on the rear panel.
Mic Input
Guitar Input
Line Left
Line Right
mic rvb mic dry
line rvb line dry
SC
mic fx
line fx
= Speaker Compensation Module
Delay Reverb
++XLR Left Output
XLR Right Output
1/4" Left Output
1/4" Right Output
++
+SC
SC
SC
SC
Pickup
Sim Wah Comp Stompbox CH 1
Cabinet
Comp
Detector Gate Detector
Whammy/IPS
(except
Talker)
CH 1Amp
Modeling/
Tone
CH 1
Cabinet
CH 1Amp
Modeling/
Tone
CH 2
Cabinet
CH 2Amp
Modeling/
Tone
Gate Whammy/IPS
(Talker) Chorus/
Mod +
++
DRUMS,
RECORDER,
USB PLAYBACK
Mic Input
Guitar Input
Line Left
Line Right
mic rvb mic dry
line rvb line dry
SC
mic fx
line fx
= Speaker Compensation Module
Delay Reverb
++
XLR Left Output
XLR Right Output
1/4" Left Output
1/4" Right Output
++
+SC
SC
SC
SC
Pickup
Sim Wah Comp Stompbox CH 1
Cabinet
Comp
Detector Gate Detector
Whammy/IPS
(except
Talker)
CH 1Amp
Modeling/
Tone
CH 1
Cabinet
CH 1Amp
Modeling/
Tone
CH 2
Cabinet
CH 2Amp
Modeling/
Tone
Gate Whammy/IPS
(Talker) Chorus/
Mod
+++
DRUMS,
RECORDER,
USB PLAYBACK
Mic Input
Guitar Input
Line Left
Line Right
mic rvb mic dry
line rvb line dry
SC = Speaker Compensation Module
mic fx
line fx
Delay Reverb
++
XLR Left Output
XLR Right Output
1/4" Left Output
1/4" Right Output
++
+SC
SC
SC
SC
Pickup
Sim Wah Comp Stompbox CH 1
Cabinet
Comp
Detector Gate Detector
Whammy/IPS
(except
Talker)
CH 1Amp
Modeling/
Tone
CH 1
Cabinet
CH 1Amp
Modeling/
Tone
CH 2
Cabinet
CH 2Amp
Modeling/
Tone
Gate Whammy/IPS
(Talker) Chorus/
Mod
+
+
+
+
DRUMS,
RECORDER,
USB PLAYBACK
10
Audio Routing Setups