DigiPos WD-2030 User manual

Vacuum Fluorescent
Customer Display
Model: WD-2030 XXXX
Version: 1.2

WD-2030 XXXX customer display
1
INDEX
1. FEATURES.........................................................................................................3
2. GENERAL SPECIFICATIONS.........................................................................4
3. UNPACKING AND CHECKING THE PARTS................................................5
3.1 P
ARTS LIST
(W
ITH
B
ASE
PCB) ..........................................................................5
3.2 P
ARTS LIST
(W
ITHOUT
B
ASE
PCB) ....................................................................6
3.3 M
ODEL
N
UMBER
...............................................................................................7
4. DISPLAY MODULE INTERFACE...................................................................8
4.1 RS232 S
PECIFICATIONS
.....................................................................................8
4.1.1 RS232 connector to PCB (CN1)..................................................................8
4.1.2 RS232 connector to PCB (CN6)..................................................................9
4.1.3 RS232 connector to PCB (CN7)................................................................10
4.2 USB
SPECIFICATIONS
......................................................................................10
4.2.1 USB connector to PCB (CN2)...................................................................10
4.3 P
OWER
USB
SPECIFICATIONS
...........................................................................11
4.3.1 USB Connector to PCB (CN2+CN9) ........................................................11
5. BASE PCB INTERFACE.................................................................................12
5.1 RS-232 I
NTERFACE CONNECTOR
(O
N THE BOTTOM OF THE BASE SECTION
) ........12
5.2 P
OWER
S
UPPLY
C
ONNECTORS
..........................................................................12
5.2.1 CN2 / Type: DC jack (5.5/2.1)..................................................................12
5.2.2 CN1,CN6 / Type: Miniature jacks quick lock 3 pin...................................12
5.3 CN5 / T
YPE
: DB25/F
TOGETHER WITH SIGNALS OF
RS-232C............................12
5.4 RS232C
LINK TO
PC/HOST
CONNECTOR
(CN5)...............................................13
5.5 RS232C
LINK TO PRINTER CONNECTOR
(CN3)..................................................13
5.6 RS232C
LINK TO DISPLAY PANEL
(CN4)..........................................................13
6. USB BASE INTERFACE .................................................................................14
6.1 USB I
NTERFACE CONNECTOR
(O
N THE BUTTOM OF THE BASE SECTION
).............14
6.2 P
OWER
S
UPPLY
C
ONNECTORS
..........................................................................14
6.2.1 CN1,CN6 / Type: Miniature jacks quick lock 3 pin...................................14
6.2.2 CN2 / Type: DC jack (5.5/2.1)..................................................................14
6.3 USB
INPUT PORT LINK TO
PC/HOST USB
CONNECTOR
(CN5)..........................15
6.4 RS232C
LINK TO PRINTER CONNECTOR
(CN3)..................................................15
6.5 RS232C
LINK TO DISPLAY PANNEL
(CN4)........................................................15
7. DIP SWITCH SETTING..................................................................................16
7.1 C
OMMAND TYPE SELECTION
............................................................................16
7.2 B
AUD RATE SELECTION
....................................................................................16
7.3 P
ARITY CHECK SELECTION
...............................................................................16
7.4
I
NTERNATIONAL CHARACTER SET SELECTION
...................................................17
7.5 S
ELF
-
TEST
&
DEMO FUNCTION SELECTION
........................................................17
8. COMMAND......................................................................................................18

WD-2030 XXXX customer display
2
8.1 CD5220 S
TANDARD
M
ODE
C
OMMAND
L
IST
.....................................................18
8.2 UTC
STANDARD MODE COMMAND LIST
............................................................21
8.3 UTC
ENHANCED MODE COMMAND LIST
............................................................22
8.4 AEDEX
MODE COMMAND LIST
........................................................................23
8.5 PD3000
MODE COMMAND LIST
........................................................................23
8.6 ADM788
MODE COMMAND LIST
......................................................................24
8.7 DSP-800
MODE COMMAND LIST
.......................................................................25
8.8 EPSON E
SC
/
POS COMMAND LIST
.....................................................................27
9. CHARACTER SET ..........................................................................................30
9.1 USA,
STANDARD CHARACTER SET
(20
H
– 7E
H
).................................................30
9.2 I
NTERNATIONAL
C
HARACTER
S
ETS
..................................................................31
9.3 P
AGE
0 (PC437: USA, S
TANDARD
E
UROPE
) (80H – FFH) ................................32
9.4 P
AGE
1 (K
ATAKANA
) (80H – FFH)..................................................................33
9.5 P
AGE
2 (PC850: M
ULTILINGUAL
) (80H – FFH)................................................34
9.6 P
AGE
3 (PC860: P
ORTUGUESE
) (80H – FFH) ...................................................35
9.7 P
AGE
4 (PC863: C
ANADIAN
-F
RENCH
) (80H – FFH).........................................36
9.8 P
AGE
5 (PC865: N
ORDIC
) (80H – FFH) ...........................................................37
9.9 P
AGE
6 (S
LAVONIC
) (80H – FFH)....................................................................38
9.10 P
AGE
7 (R
USSIA
) (80H – FFH) ......................................................................39
9.11 P
AGE
19 (PC858 E
URO
) (80H – FFH)............................................................40
9.12 P
AGE
12 (G
REEK
) (80H – FFH).....................................................................41
9.13 P
AGE
26 (WPC-1257) (80H – FFH)...............................................................42
APPENDIX A: DISPLAY WITH RECTANGLE BASE DIMENSION..............43
APPENDIX B: DISPLAY WITH ROUND BASE DIMENSION........................43
APPENDIX C: RECTANGLE BASE DIMENSION...........................................44
APPENDIX D: ROUND BASE DIMENSION.....................................................44
APPENDIX E: TUBE DIMENSION....................................................................45
APPENDIX F: PASS THROUGH INSTALLATION GUIDE............................47

WD-2030 XXXX customer display
3
1. FEATURES
1. Data can be displayed on 20 columns x 2 lines.
2. Blue-green color and large character are easy to eye.
3. The display panel is adjustable to provide the best view angle.
4. Provide 2 poles for base position installation.
5. The DIP-switches setting emulate commands mode, baud rate and
international characters.
6. CD5220/UTC/EMAX/ADM/EscPOS/DSP-800 emulation command sets.
7. Characters can be defined by user-defined character commands. (For
Esc/POS/CD5220/DSP 800 command).
8. Provides an interface based on USB emulation RS-232C, baud rate
4,800, 9,600, 19,200 and 115,200 bps.
9. The VFD customer display and printer can be connected by
pass-through (ref. Appendix F).
10. Various power connectors and wide range power input (5VDC or
9~45VDC).

WD-2030 XXXX customer display
4
2. GENERAL SPECIFICATIONS
NO
ITEM Descriptions
1 Display method Vacuum fluorescent display
2 Number of character 20 columns x 2 lines
3 Character font 5 x 7 Dot matrix
4 Display color Blue green
5 Brightness 700 cd/ m
2
6 Fonts 96 alphanumeric 13 kinds of international character sets
1 kind of user define character set
7 Character size 9.03 mm x 5. 25 mm
8 Power supply 5VDC or 9~ 45VDC
9 Power consumption 6 W (Max.)
10 MTBF 30,000 hours (power on time)
11 Panel dimensions 224 (W) x 93 (H) x 50(D) mm
12 External dimensions Long 225(W) x 100(D) 500(H)mm Middle 225(W) x 100(D) 281(H)mm
Short 225(W) x 100(D) 193(H)mm
13 Viewing angle (Horizontal) 120 degrees
14 Viewing angle (Vertical) 90 degrees
15 Rotation angle (Horizontal)
350 degrees
16 Tilt angle 0 ~ 60 degrees
17 Weight 1.25 Kg
18 Operating temperature 0 ~ 45℃
19 Operating Humidity 10%~90%
20 Storage Temperature -10 ~ 50℃
21 Storage Humidity 10%~90%
Table 2-1

WD-2030 XXXX customer display
5
3. UNPACKING AND CHECKING THE PARTS
3.1 Parts list (With Base PCB)
(1)
D
isplay Module.
(2) Nut.
(3) Knob.
(4) Neck.
(5) Display Cable.
(6) Long Pole
(7) Short Pole
(8) Base Housing.
(9) Base PCB.
(10) Power Adapter
(11) AC Cord
(12) Signal transmission line.
(13) Plate.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(12)
(13)
(11)
(10)
(9)

WD-2030 XXXX customer display
6
3.2 Parts list (Without Base PCB)
(1)
D
isplay Module.
(2) Nut.
(3) Knob.
(4) Neck.
(5) Long Pole
(6) Short Pole
(7) Base Housing.
(8) Signal transmission line.
(1)
(8)
(6)
(5)
(4)
(3)
(2)
(7)

WD-2030 XXXX customer display
7
3.3 Model Number
WD-2030 X X X X
1
2
3
4
I
nterface
(Display Module)
Base Type Power Input Color
R:
RS
-
232 12V
S:RS-232 5V
U:USB
O:Power USB 5V
P:Power USB 12V
Q:Power USB 24V
R:
RS
-
232 Base
U:USB-B Base
H:HUSB Base
S:Only Rectangular
Base Housing
C:Only Circular
Base Housing
N:No Base
M:Module + Neck
A:
USA Cord + SPS
B:Jap.Cord + SPS
C:Eur. Cord + SPS
D:U.K Cord + SPS
E:Fra. Cord + SPS
F:Asu.Cord + SPS
G:SA. Cord + SPS
Y:No AC Cord + SPS
H:USA Cord + IEC
I:Jap.Cord + IEC
J:Eur. Cord + IEC
K:U.K Cord + IEC
L:Fra. Cord + IEC
M:Asu.Cord + IEC
N:SA. Cord + IEC
Z:No AC Cord + IEC
W:No AC Cord + No Power
1:USA Adaptor
2:Jap. Adaptor
3:Eur. Adaptor
4:U.K Adaptor
5:Fra. Adaptor
6:Asu. Adaptor
7:SA. Adaptor
O:Power USB 5V
P:Power USB 12V
Q:Power USB 24V
R:RS-232 Port(PC)
S:RS-232 DC Jack + No Power
U:USB Port(PC)
V:USB Plug (POWER SUPPY)
B:
Black
W:
White
Table 3-2
1
2
3
4

WD-2030 XXXX customer display
8
4. Display Module Interface
4.1 RS232 Specifications
Data transmission: Serial
Synchronization: Asynchronous
Handshaking: DTR / DSR
Signal level:
MARK =
-
3 to
–
15 V (logic “1”)
SPACE = +3 to +15 V (logic “0”)
Baud rates: 4800,9600,19200 or 115200 bps
Parity and bit length
None parity, 8 data bits or
Even parity, 7 data bits
Stop bits: 1 or more
Table 4-1
4.1.1 RS232 connector to PCB (CN1)
Type: RJ45/8P/8C
Pin assignment
No
Signal
Direction Function description
1,2
Vin - Power 5VDC or 9~45 VDC
3,4
GND - Signal ground
5 CTS From Printer to Display Printer ready signal
6 RTS From Display to PC/Host Display/Printer ready signal
7 RXD From PC/Host to Display Display/Printing data signal
8 TXD From Display to Printer Printer status data signal
Table 4-2

WD-2030 XXXX customer display
9
4.1.2 RS232 connector to PCB (CN6)
Type: PH 2.0 mm/8P
Pin assignment
No
Signal
Direction Function description
1,2
Vin - Power 5VDC or 9~45 VDC
3,4
GND - Signal ground
5 CTS From Printer to Display Printer ready signal
6 RTS From Display to PC/Host Display/Printer ready signal
7 RXD From PC/Host to Display Display/Printing data signal
8 TXD From Display to Printer Printer status data signal
Table 4-3

WD-2030 XXXX customer display
10
4.1.3 RS232 connector to PCB (CN7)
Type: PH 2.0 mm/9P
Pin assignment
No
Signal
Direction Function description
1 NC - -
2 TXD From Display to Printer Printer status data signal
3 RXD From PC/Host to Display Display/Printing data signal
4 CTS From Printer to Display Printer ready signal
5 GND - Signal ground
6,8
RTS From Display to PC/Host Display/Printer ready signal
7 NC - -
9 Vin - Power 5VDC or 9 ~ 45 VDC
Table 4-4
4.2 USB specifications
Data transmission: USB emulation RS232C
Synchronization: Asynchronous
Handshaking: DTR / DSR
Signal level: 0~+3V
Baud rates: 4800,9600,19200 or 115200 bps
Parity and bit length
None parity, 8 data bits or
Even parity, 7 data bits
Stop bits: 1 or more
Table 4-5
4.2.1 USB connector to PCB (CN2)
Type: WAFER PH 2.0mm 4P
Pin assi
gn
men
t
No
Signal
Direction
Function de
scription
1
V+
5V From PC/Host USB power 5 VDC
2
D
-
Data signal -
3
D
+
Data signal+
4
GND
Signal ground
Table 4-6

WD-2030 XXXX customer display
11
4.3 Power USB specifications
Data transmission: USB emulation RS232C
Synchronization: Asynchronous
Handshaking: DTR / DSR
Signal level: 0~+3V
Baud rates: 4800,9600,19200 or 115200 bps
Parity and bit length
None parity, 8 data bits or
Even parity, 7 data bits
Stop bits: 1 or more
Table 4-7
4.3.1 USB Connector to PCB (CN2+CN9)
CN2
Type: WAFER PH 2.0mm 4P
Pin assi
gn
men
t
No
Signal
Direction
Function description
1
V+
5V From PC/Host USB power 5 VDC
2
D
-
Data signal -
3
D
+
Data signal+
4
GND
Signal ground
Table 4-8
CN9
Type: WAFER PH 2.0mm 5P
Pin assi
gn
men
t
No
Sign
al
Direction
Function description
2,3
V+
5/12/24V From PC/Host VPLUS
1,4
GND
PWR Ground Signal ground
5
FG
Data signal+
Table 4-9

WD-2030 XXXX customer display
12
5. Base PCB Interface
5.1 RS-232 Interface connector (On the bottom of the base
section)
CN1,CN6: 24VDC power supply pass-through connects
CN2: Power input connector from adapter
CN3: RS-232C connect to printer
CN4: Connect to display panel
CN5: RS-232C connect to PC/Host
5.2 Power Supply Connectors
The variable power input which are available on base connectors, but only
if one connector can be selected for power input, the description as below:
5.2.1 CN2 / Type: DC jack (5.5/2.1)
Pin assignmen
t
No
Signal
+
Vin1
-
GND
Table 5-1
5.2.2 CN1,CN6 / Type: Miniature jacks quick lock 3 pin
Table 5-2
5.3 CN5 / Type: DB25/F together with signals of RS-232C
Table 5-3
Pin assignmen
t
No
Sig
nal
1
Vin2
2
GND
Pin assignment
No
Signal
16,25
Vin3
7
GND

WD-2030 XXXX customer display
13
5.4 RS232C link to PC/HOST connector (CN5)
Type: DB25/F
Pin assignment
No
Signal
Direction
Function description
2
TXD
From printer to PC/Host
Printer status data
3
RXD
From PC/Host to display
Receive data
4,20
DTR
From display to PC/Host
Display/printer ready signal
6
DSR
From PC/Host to printer
PC/Host ready signal
7
GND
-
Signal g
r
ound
16,25
Vin3
From PC/Host to display
Power input
Table 5-4
5.5 RS232C link to printer connector (CN3)
Type: DB9/M
Pin assignment
No
Signal
Direction Function description
2 RXD From printer to PC/Host Printer status data
3 TXD From display to printer Printing data
5 GND - Signal ground
4,7
DTR From PC/Host to printer PC/Host ready signal
6 DSR From printer to display Printer ready signal
9 Vin2 From Hosiden to printer Power through to printer
Table 5-5
5.6 RS232C link to display panel (CN4)
Type: RJ45/8P/8C
Pin assignment
No
Signal
Direction Function description
1,2
Vin - Power 5VDC or 9~45 VDC
3,4
GND - Signal ground
5 DSR From Printer to Display Printer ready signal
6 DTR From Display to PC/Host Display/Printer ready signal
7 RXD From PC/Host to Display Display/Printing data signal
8 TXD From Display to Printer Printer status data signal
Table 5-6

WD-2030 XXXX customer display
14
6. USB BASE INTERFACE
6.1 USB Interface connector (On the buttom of the base
section)
CN1,CN6: 24VDC power supply pass-through connects
CN2: Power input connector from adapter
CN3: RS-232C connect to printer
CN4: Connect to display panel
CN5: USB input
6.2 Power Supply Connectors
There are variable power inputs which are available on base connector,
but only one connector can be selected for power input function, the
description as below:
6.2.1 CN1,CN6 / Type: Miniature jacks quick lock 3 pin
Pin assignment
No
Signal
1
Vin2
2
GND
Table 6-1
6.2.2 CN2 / Type: DC jack (5.5/2.1)
Pin assignment
No
Signal
+
Vin1
-
GND
Table 6-2

WD-2030 XXXX customer display
15
6.3 USB input port link to PC/HOST USB connector (CN5)
Type: USB
Pin assignment
No
Signal
Direction
Function description
1
V+
5V From PC/Host
USB power 5 V
DC
2
D
-
Data signal
-
3
D
+
Data signal
+
4
GND
-
Signal g
r
ound
Table 6-3
6.4 RS232C link to printer connector (CN3)
Type: DB9/M Pin assignment
No
Signal
Direction Function description
2 RXD From printer to PC/Host Printer status data
3 TXD From display to printer Printing data
5 GND - Signal ground
4,7
DTR From PC/Host to printer PC/Host ready signal
6 DSR From printer to display Printer ready signal
9 Vin2 From Hosiden to printer Power through to printer
Table 6-4
6.5 RS232C link to display pannel (CN4)
Type: RJ45/8P/8C Pin assignment
No
Signal
Direction Function description
1,2
Vin - Power 5VDC or 9~45 VDC
3,4
GND - Signal ground
5 DSR From Printer to Display Printer ready signal
6 DTR From Display to PC/Host Display/Printer ready signal
7 RXD From PC/Host to Display Display/Printing data signal
8 TXD From Display to Printer Printer status data signal
Table 6-5

WD-2030 XXXX customer display
16
7. DIP SWITCH SETTING
7.1 Command type selection
SW1 SW2 SW3 Command type
ON ON ON DSP800
OFF ON ON ESC/pos
ON OFF ON PD3000
OFF OFF ON ADM 788
ON ON OFF EMAX(Aedex)
OFF ON OFF UTC/P
ON OFF OFF UTC/S
OFF OFF OFF CD5220
Table 7-1
7.2 Baud rate selection
SW8 SW9 Baud rate (bps)
ON ON 4800
OFF ON 9600
ON OFF 19200
OFF OFF 115200
Table 7-2
7.3 Parity check selection
SW10 Parity & data bits
ON None-parity , 8 data bits
OFF Even-parity , 7 data bits
Table 7-3
ON
1 2 3 4 5 6 7 8 9 10 11 12
DIP

WD-2030 XXXX customer display
17
7.4 International character set selection
SW4 SW5 SW6 SW7 Character set Code table ( 80H-FFH)
ON ON ON ON U.S.A. PC-437(USA&Europe)
OFF ON ON ON France PC-858(Euro)
ON OFF ON ON Germany PC-858(Euro)
OFF OFF ON ON U.K. PC-858(Euro)
ON ON OFF ON Denmark I PC-858(Euro)
OFF ON OFF ON Sweden PC-858(Euro)
ON OFF OFF ON Italy PC-858(Euro)
OFF OFF OFF ON Spain PC-858(Euro)
ON ON ON OFF Japan Katakana
OFF ON ON OFF Norway PC-858(Euro)
ON OFF ON OFF Denmark II PC-858(Euro)
OFF OFF ON OFF U.S.A Slavonic
ON ON OFF OFF U.S.A Russia
OFF ON OFF OFF U.S.A PC860 (Portuguese)
ON OFF OFF OFF U.K. Greek
OFF OFF OFF OFF U.S.A WPC1257
Table 7-4
7.5 Self-test & demo function selection
SW11 Function
ON Enable
OFF Disable
Table 7-5
* SW12 reserve

WD-2030 XXXX customer display
18
8. COMMAND
8.1 CD5220 Standard Mode Command List
Command Code (hex) Function description
ESC DC1 1B 11 Overwrite mode
ESC DC2 1B 12 Vertical scroll mode
ESC DC3 1B 13 Horizontal scroll mode
ESC QA ....CR 1B 51 41 data x m 0D
Set the string
display mode,writed string to
upper line
m ≦20
ESC QB ....CR 1B 51 42 data x m 0D
Set the string display mode, writed string to
lower line
m ≦20
ESC QD ....CR 1B 51 44 data x m 0D Upper line message scroll continuously
m ≦40
ESC [ D 1B 5B 44 Move cursor left
BS 08 Move cursor left
ESC [ C 1B 5B 43 Move cursor right
HT 09 Move cursor right
ESC [ A 1B 5B 41 Move cursor up
ESC [ B 1B 5B 42 Move cursor down
LF 0A Move cursor down
ESC [ H 1B 5B 48 Move cursor to home position
HOM 0B Move cursor to home position
ESC [ L 1B 5B 4C Move cursor to left-most position
CR 0D Move cursor to left-most position
ESC [ R 1B 5B 52 Move cursor to right-most position
ESC [ K 1B 5B 4B Move cursor to bottom position
ESC l x y 1B 6C x y Move cursor to specified position
1 ≦x≦20 ,row position
1 ≦y≦2 ,column position

WD-2030 XXXX customer display
19
Command Code (hex) Function description
ESC @ 1B 40 Initialize display
CLR 0C Clear display screen , and clear string mode
CAN 18 Clear cursor line, and clear string mode
ESC * n 1B 2A n
Brightness adjustment
1≦n≦4
ESC & s n m
[a (P1..pa)]x
(m-n+1)
1B 26 1 n m [a(p1..pa)]
x (m-n+1)
Define download characters.
32 ≦n ≦m 255
1 ≦a ≦5
p1..p5 =row1..row5
ESC ? n 1B 3F n Deletes download characters.
32 ≦n ≦m 255
ESC % n 1B 25 n Select/cancel download character set. n = 0 , Cancel
n = 1 , Select
ESC _ n 1B 5F n Set cursor on/off n = 1 , cursor on
n = 2 , cursor off
ESC f n 1B 66 n Select international fonts set, refer *2
ESC c n 1B 63 n Select code, refer *3
ESC = n 1B 3D n Select peripheral device, display or printer n bit 0 = 1 select printer
n bit 1 = 1 select display
Table 8-1