Digital Watchdog DWC-C223W User manual

Quick Start Guide Quick Start Guide
1. The mounting surface must withstand five times the weight of
your camera.
2. Pay attention to the cables. They can easily become caught and
damaged. Any damage may cause a short or fire.
3. Remove the sensor protective cap and mount a lens to the camera.
See STEP 3 for lens information.
STEP 1 – PREPARING TO MOUNT THE CAMERA
Pass the wires through the installation surface and make all
necessary connections. Connect the BNC cable and power
cables to the camera.
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
Power requirements Power consumption
DC12V / AC24V dual-voltage DC12V: 2.45W
AC24V: 2.4W
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
WHAT’S IN THE BOX
Alarm out/
RS485 cable 1C-mount adapter 1
2P terminal
block 1IRIS plug 1
CS mount
wrench 1 Set Quick set up guide 1
Attention: This document is intended to serve as a quick reference for initial
set up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in
the ‘Search by Product’ search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
DW® Universal HD over Coax®
box cameras
DWC-C223W
CS-mount adapter
Sensor
protective cap
Back focus
adjustment bolt
Alarm +/-, RS485
BNC video output
Mounting bracket connectors
DC-Iris socket
Box camera
OSD control buttons
Power LED
AC/DC power input
terminal block
CS-mount adapter
Sensor
protective cap
Back focus
adjustment bolt
Alarm +/-, RS485
BNC video output
Mounting bracket connectors
DC-Iris socket
Box camera
OSD control buttons
Power LED
AC/DC power input
terminal block

Quick Start Guide
1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:
Use the OSD Switch to switch the camera’s signal.
- To switch the camera to HD-TVI mode, press OSD joystick to the
left for 5 seconds.
- To switch the camera to HD-Analog mode, press OSD joystick to
the right for 5 seconds.
- To switch the camera to CVBS mode, press OSD joystick up
for 5 seconds.
- To switch the camera to HD- CVI mode, press OSD joystick down
for 5 seconds.
1. For an automatic iris lens, the lens has to be connected to the
DC-Iris socket on the side of the camera.
For a lens with a manual or fixed iris, this socket is not used.
2. Before mounting a lens to the camera, check whether the lens is a
C- or CS-mount lens. The back focus of the box camera is set by
default for a CS-mount lens.
a. For a CS-mount lens: remove the protective cap from the box
camera and attach the lens into the camera by rotating
it clockwise.
b. For a C- mount lens: remove the protective cap from the box
camera and attach the lens adapter by turning it clockwise. Then,
attached the lens to the adapter by turning it clockwise.
3. Once the lens has been properly mounted to the box camera, mount
the camera on an appropriate mounting bracket (sold separately).
STEP 4 – CHANGING THE SIGNAL IN
THE CAMERA
STEP 3 – INSTALLING THE LENS
Rev Date: 09/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
12VDC/24VAC
UP
ENTER RIGHTLEFT
DOWN
NOTE: When the lens is mounted to the box camera, adjusting
the back focus may be required. If the correct focus
cannot be obtained, you may need to adjust the lens
adapter. Once the back focus is adjusted, tighten the
back focus bolt. The bolt is loose by default and will
have to be adjusted during the camera installation.
C-Mount Adapter
CS-Mount Lens
C-Mount Lens
DC Driven (DC)
1. Control +
2. Control -
3. Drive +
4. GND
DC-IRIS
2
1
3
4
C-Mount Adapter
CS-Mount Lens
C-Mount Lens
DC Driven (DC)
1. Control +
2. Control -
3. Drive +
4. GND
DC-IRIS
2
1
3
4
C-Mount Adapter
CS-Mount Lens
C-Mount Lens
DC Driven (DC)
1. Control +
2. Control -
3. Drive +
4. GND
DC-IRIS
2
1
3
4
HD-A
HD-TVI
CVBS(960H)
HD-CVI