Digital Watchdog DWC-B362DIR User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
DWC-B362DIR
Digital Bullet Camera
User Manual
01312011

22
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacture.
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera. It can cause fire, short-circuits,
or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room, as the temperature may rise to
high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface.
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to Provide reasonable protection against harmful
interference. when the equipment is operated in a residential environment. This equipment generates, uses,
and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications.

3
TROUBLESHOOTING
No VIDEO
Out-of-Focus VIDEO
Before sending your camera for repair, check the following or contact our technical specialist.
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.

4
DIMENSIONS IN MILLIMETERS*

5
CONTROL BOARD*
SW
CON 1
FUNCTIONAL OF CONTROL BOARD
[1] SW : Functional control of OSD (On Screen Display)
[2] CON 1 :Second Video Output Connector

6
CONNECTIONS*
CAUTION :
Check for polarity when using a DC 12V & AC 24V power supply.

7
CAMERA SETTING ANGLE*
①
②
ATTENTION
Do not rotate ① more than 360°
Do not unnecessarily twist ② too many times.

8
OSD MENU SETTINGS*
EXPOSURE
LENS DC / MANUAL
SHUTTER 1/160, 1/100, FLC, 1/250 ~ 100000
OFF / ON
BLC (Back Lignt Compensation)
BLC
AGC OFF ~ 36dB
EXIT JUMP
COLOR
WB MODE AWC / ATW / PUSH LOCK / MANUAL (AWC is recommended.)
R - Y GAIN 0 ~ 255
EXIT JUMP
DAY&NIGHT
DAY&NIGHT MODE AUTO / COLOR / BW
B - Y GAIN 0 ~ 255
EXIT JUMP
FUNCTION
MIRROR OFF / ON
SHARPNESS 0 ~ 49
GAMMA 0.05 ~ 1.00 / USER
OFF / ON
SLC (Side Light Compensation)
OFF / ON
DRC (Dynamic Range Compressor)
EXIT JUMP
SLC
DRC
HME OFF / ON
HME (Highlight Masking Exposure)

9
MOTION
DELAY OUT (1 ~ 15)
Motion Alarm Zoom-In Delay
SET WINDOW
MOTION
EXIT JUMP
OFF / ON
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (0 ~ 55)
SHOW INDICATOR (OFF / Icon / TRACE)
PRIVACY
OFF / ON
SET WINDOW
OFF / ON
SET WINDOW
OFF / ON
SET WINDOW
SET WINDOW
MASK 1
MASK 2
MASK 3
MASK 4 OFF / ON
COLOR SET BLACK / GRAY / COLOR 1 ~ 6
EXIT JUMP

10
SETUP
0 ~ 255
TOP_L/TOP_R/BOT_L/BOT_R
OFF / ON
CAMERA ID
TITLE EDIT
TITLE RESET
TITLE POS.
LANGUAGE
DPC SET
WHITE THR. 0~255
BLACK THR. 0~255
DPC LEVEL. 0~255
English, Chinese
EXIT
EXIT
SAVE & EXIT
FACTORY SET
PC CONT.
EXIT JUMP
OFF / ON