Digital Watchdog DWC-PV2M4T User manual

MEGApix® Panoramic
2.1MP 180° Camera
DWC-PV2M4T
User’sManual Ver. 1.0 / 2015.04.21
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.

S af et y I nf or ma tion
1
Warning Precaution
This symbol indicates that dangerous voltage
consisting a risk of electric shock is present within
this unit.
Thisexclamation pointsymbolisintended to alert the
user to the presence of important operating and
maintenance (servicing)instructions intheliterature
accompanying theappliance.
WARNING
To prevent damage which may result in fire or electric shock
hazard, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in
thespecification sheet. Usinganyotheradaptercould cause
fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery
may cause explosion, fire, electric shock, or damage to the
product.
3. Do not connect multiple cameras to a single adapter.
Exceeding the capacity may cause excessive heat generation
or fire.
4. Securely plug the power cord into the power receptacle.
Insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly.
A falling camera may cause personal injury.
6. Do not place conductive objects (e.g. screw drivers, coins,
metal items, etc.) or containers filled with water on top of
the camera. Doing so may cause personal injury due to fire,
electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations.
Doing so may cause fire or electric shock.
8. If any unusual smells or smoke come from the unit, stop
usingtheproduct.Immediatelydisconnectthepower
source and contact the service center. Continued use in
such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest
service center. Never disassemble or modify this product in
any way.
10. When cleaning, do not spray water directly onto parts of the
product. Doing so may cause fire or electric shock.
Precaution
Operating
• Before using, make sure power supply and all other parts are
properly connected.
• While operating, if any abnormal condition or malfunction
is observed, stop using the camera immediately and contact
your dealer.
Handling
• Do not disassemble or tamper with parts inside the camera.
• Do not drop the camera or subject it to shock or vibration as
this can damage the camera.
• Clean the clear dome cover with extra care. Scratches and
dust can ruin the quality of the camera image.
Installation and Storage
• Do not install the camera in areas of extreme temperature,
exceeding the allowed range.
• Avoid installing in humid or dusty environments.
• Avoid installing in places where radiation is present.
• Avoid installing in places where there are strong magnetic
fields and electric signals.
• Avoid installing in places where the camera would be subject
to strong vibrations.
• Never expose the camera to rain or water.
CA UT IO N
RIS K O F ELE C TRI C SH O CK .
D O NOT O PE N.
CAUTION
:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

2
Important Safety Instructions
1. Read these instructions. - All these safety and operating instructions should be read before the product is
installed or operated.
2. Keep these instructions. - The safety, operating and use instructions should be retained for future reference.
3. Heed all warnings. - All warnings on the product and in the operating instructions should be adhered to.
4. Follow all instructions. - All operating and use instructions should be followed.
5. Do not use this device near water. - For example: near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet
basement; near a swimming pool; etc.
6. Clean only with dry cloth. - Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. - Slots and
openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it
from over-heating. The openings should never be blocked by placing the product on bed, sofa, rug or other similar
surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and the manufacturer’s instructions have been adhered to.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers)
that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.

3
Disposal of OldAppliances
1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by
the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately form the municipal waste
stream in accordance to laws designated by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for
the environment and human health.
waste disposal service or the shop where you purchased the product.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a com mercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the in struction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful inte rference in which case the user
will be required to correct the interference at his own expense.

4
I n tr oduc tion -
P r oduc t & Acc essor ies
Please check that all the following accessories are included in the package.
Camera Cables
Quick Manual
Screw & Plastic Anchor-4pcs
Manual CD
T-Wrench
(For Lens Tilting and
Rotation Control)
Template Sheet
Torx Wrench
(For SD CardCap)
Test Monitor Cable
Six anglesWrench
(For Hard Lock Set Screw)

5
Introduction -
Product & Accessories
Mount Bracket
3 Panoramic Lens
Tilt,Rotation Control
OSD Cap
Main Body
Reset Button
Cables
SD card Slot
¾” Pipe Mounting Hole
Hard Lock Set Screw

6
I nstallation -
Disassemble the Camera
Before installing your camera, you have to read the following cautions.
2. Don’t let the cable to be caught in improper place or the electric line cover to be damaged. Otherwise
3. When installing your camera, don’t allow any person to approach the installation site. If you have any
valuable things under the place, move them away.
1
Disassemble the camera
Loosen a small hard lock set screw on the Mount Bracket
using a small six angles wrench to disassemble the
camera from a Mount Bracket to for installation.
Warning:
Never Open the Dome.
Supplier will not take any responsibility on any
defectionfromanarbitrary disassembly.

7
Installation -
Mounting the Camera
Template Sheet
1
Disassemble the camera, See the section ‘Disassemble
the camera’ for details.
2
Using the template sheet, make the cabling holes on
the wall/ceiling.
3
Fix the Mount bracket on the wall/ceiling by
screw provided.
4
Hook the Main body to Mount bracket with safetywire.
S Bring the cables into the Mount bracket through the hole.
6 Connect the cables respectively. See the section
‘Cabling’ for details.
7 After connecting the cables, main body to be assembled
into the Mount bracket.
8 Detach the protection film from the Dome Cover.
9 Adjust the panning angle of the camera and tighten
the hard lock set screw on the camera's Dome. See
next page for more information.
Safety Wire
Mount Bracket Hole
2
3
4
S
6
7
8

8
Installation -
Adjusting the Camera's Pan and Tilt
6 Pull wires through and make all necessary
connections. See 'Cabling' section for more
information.
7 Connect the camera's main body to the mounting
bracket.
8 Adjust the panning angle of the camera and tighten
hard lock set screw to fix the camera. Use the
included six-angle wrench included with the camera
to tighten the screw and secure the camera module
to the mounting bracket.
9 Adjust the lens' angle by adjusting the controlling
screws on the main body. Use the included T-
wrench. The screws located at the base of the
camera dome control the lens' tilt up and down and
its rotation.
Lens Tilt Lens Rotation
10 When the installation is complete, detach the
protective film from the camera’s dome.
Warning:
The camera's lens module can rotate 360¡ at each
direction. Rotating the lens constantly to the same
direction may harm the internal rotation mechanism
and cause the lens' rotation harness to snap.
Tilting Range
Rotating Range
0° ~ 90°
0° ~ 360°

9
Installation -
Inserting / Removing the SD Memory Card
1
To open the SD card slot, use the included Torx wrench.
2 Insert the SD card in the arrow direction.
Do not insert the SD memory card while it’s upside down by
force. Otherwise, it may damage the SD memory card.
Main Body
3
Removing an SD Memory Card Gently press down on the
Remove the SD Memory Card gently by pressing down on
the exposed end of the memory card as shown in the
diagram to eject the memory card from the slot.
Pressing too hard on the SD memory card may cause the card to
shoot out uncontrollably from the slot when released.
If you have saved data in the SD memory card, removing the SD
memory card prior to setting record to OFF will cause damage to
the data stored in the card.
SD card Slot
T he memor y c a rd is a n extern a l da ta st or ag e devi ce
tha t h as
to record and share video, audio, and text data using
digital devices.
Micro
( Not Included )
-Type: Micro SD (SDHC)
- Manufacturer: Transcend, Kingston, Toshiba, SanDisk
- Capacity: 4~16G
-Class: over Class 6