Digital Watchdog D2362DIR User manual

5436 W Crenshaw St. Tampa, FL 33634
Tel: [phone]
Fax: [phone]
www.Digital-Watchdog.com
[email protected]
Technical Support Hours: Monday-Friday
8:30am to 8:00pm Eastern Time
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
ABOUT MANUAL
01302012
User Manual
D2362DIR, D2363D, D2363TIR
D2367WD, D2367WTIR
D2382TIR, D2365T
Indoor Dome Camera

■ Do not open or modify.
■ Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
■ Do not put objects into the unit.
■
Keep metal objects and ammable substances from entering the camera. It can cause re, short- circuits,
or other damages.
■ Be careful when handling the unit.
■To prevent damages, do not drop the camera or subject it to shock or vibration.
■Do not install near electric or magnetic elds.
■Protect from humidity and dust.
■Protect from high temperature.
■
Be careful when installing near the ceiling of a kitchen or a boiler room, as the temperature may rise to
high levels.
■Cleaning
■To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
■Mounting Surface
■The material of the mounting surface must be strong enough to support the camera.
PRECAUTIONS
Before sending your camera for repair, check the following or contact our technical specialist.
No VIDEO
Check the coaxial cable and make sure it is connected securely.
Check the lens’iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Out-of-Focus VIDEO
Check the clear dome cover and the lens for dirt or ngerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.
TROUBSHOOTING
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to Provide reasonable protection against harmful
interference .when the equipment is operated in a residential environment.This equipment generates, uses,
and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications.
WARNING :Changes or modications are not expressly approved by the manufacture.
FCC COMPLIANCE
32

54
■1/3”High Resolution CCD
■540 TV Lines
■3.3 ~ 12mm Varifocal Auto Iris Lens
■100ft Range IR with Intelligent Camera Sync
■Electronic Day and Night
■DRC (Dynamic Range Compressor)
■HME (Highlight Masking Exposure)
■SLC (Side Light Compensation)
■AGC / BLC / AWB
■Negative Imaging
■Mirror Image Control
■RS485 Built-In
■Programmable Privacy Zone (4) & Motion Detection
■Easy Icon Driven OSD Menu with Built-In Joystick
■Secondary Video-BNC Output
■1/3”High Resolution CCD
■High Resolution 560 TV Lines
■3.3 ~ 12mm Varifocal Auto Iris Lens
■Electronic Day and Night
■Star-Light (Super Low LightTechnology)
■DRC (Dynamic Range Compressor)
■3D-DNR (3D Digital Noise Reduction)
■HME (Highlight Masking Exposure)
■Negative Imaging
■AGC / BLC / AWB
■Programmable Privacy Zone (6) & Motion Detection
■Easy Icon Driven OSD Menu with Built-In Joystick
■Auto Sensing 12VDC or 24VAC with Line Lock
■Secondary Video-BNC Output
FEATURES*-D2362DIR FEATURES*-D2363D

76
■1/3”High Resolution CCD
■High Resolution 560 TV Lines
■3.3 ~ 12mm Varifocal Auto Iris Lens
■Electronic Day and Night
■100ft Range IR with Intelligent Camera Sync
■True Day and Night / TDN5
■Star-Light (Super Low LightTechnology)
■DRC (Dynamic Range Compressor)
■3D-DNR (3D Digital Noise Reduction)
■HME (Highlight Masking Exposure)
■Negative Imaging
■AGC / BLC / AWB
■Programmable Privacy Zone (6) & Motion Detection
■Easy Icon Driven OSD Menu with Built-In Joystick
■Auto Sensing 12VDC or 24VAC with Line Lock
■Secondary Video-BNC Output
FEATURES*-D2363TIR FEATURES*-D2367WD
■1/3”Sony Super HAD II CCD
■560 TV Lines
■3.3 ~ 12mm Varifocal Auto Iris Lens
■Electronic Day and Night
■EWDR (Electronic Wide Dynamic Range)
■Star-Light (Super Low LightTechnology)
■DSS (Digital Slow Shutter)
■3D-DNR (3D Digital Noise Reduction)
■DIS (Digital Image Stabilizer)
■HME (Highlight Masking Exposure)
■AGC / BLC / AWB
■Programmable Privacy Zone (6) & Motion Detection
■Easy Icon Driven OSD Menu with Built-in Joystick
■Auto Sensing 12VDC/24VAC with Line Lock
■Secondary Video-BNC Output

98
FEATURES*-D2367WTIR
■1/3”Sony Super HAD II CCD
■560 TV Lines
■3.3 ~ 12mm Varifocal Auto Iris Lens
■100ft Range IR with Intelligent Camera Sync
■True Day and Night / TDN5
■EWDR (Electronic Wide Dynamic Range)
■Star-Light (Super Low LightTechnology)
■DSS (Digital Slow Shutter)
■3D-DNR (3D Digital Noise Reduction)
■DIS (Digital Image Stabilizer)
■HME (Highlight Masking Exposure)
■AGC / BLC / AWB
■Programmable Privacy Zone (6) & Motion Detection
■Easy Icon Driven OSD Menu with Built-in Joystick
■Auto Sensing 12VDC/24VAC with Line Lock
■Secondary Video-BNC Output
FEATURES*-D2382TIR
■1/3”Sony Super HAD II CCD
■High Resolution 560TV Lines
■OMNI-Focus 2.9~8.5mm 3X Motorized Zoom, Auto Iris 70ft Range IR with Intelligent Camera Sync
■True Day & Night / TDN5 (Electro Magnetic Mechanism)
■Max-DR (Electronic Wide Dynamic Range)
Enables the camera to capture perfect images in both bright and dark environments simultaneously.
■3D-DNR (3D Digital Noise Reduction)
Produces less noise and more color during low-light application.
■HME (Highlight Mask Exposure)
Masks overly exposed light to produce a true video image of any environment.
■SLC (Side Light Compensation)
■DIS (Digital Image Stabilizer)
■Programmable Privacy Zone (6) & Motion Detection Easy Icon Driven OSD Menu with Built-In Joystick
■Auto Sensing 12VDC or 24VAC with Line Lock
■No Fog or Condensation under AnyWeather Condition

DIMENSION (mm)*
109.6
103.1
41.3
6.5

145
117.0
125.0

5.0

4.5
91.0
91.0
85.0
85.0
L= 300mm
RS485 (Black+ & White -)
VIDEO(yellow)
BNC JACK
DC 12V or AC24V
5mm TWIST SOLDERING
RED
BLACK
FEATURES*-D2365T
1110
■1/3" Pixim Seawolf CMOS Sensor
■690 Horizontal TV Lines
■3.3 ~ 12mm Varifocal Auto Iris Lens
■TDN (True Day and Night/IR Cut Filter)
■3D-DNR (3D Digital Noise Reduction)
■Powerful Wide Dynamic Range
■Smear Canceling Circuit
■AGC / BLC / AWB
■DIS (Digital Image Stabilizer)
■HME (Highlight Masking Exposure)
■AGC / BLC / AWB
■Programmable Privacy Zone (6) & Motion Detection
■Easy Icon Driven OSD Menu with Built-in Joystick
■Low Power Consumption
■Auto Sensing 24VAC/12VDC with Line Lock
■Secondary Video-BNC Output

1312
Power Requirement *
Power Wire Maximum Distance
Wire Gauge 12VDC 24VAC
24 AWG 80feet 323feet
22 AWG 128feet 513feet
20 AWG 203feet 815feet
18 AWG 323feet 1295feet
16 AWG 514feet 2056feet
14 AWG 816feet 3264feet
12 AWG 1295feet 5183feet
10 AWG 2057feet 8228feet
Coaxial Cable Type Maximum Distance
RG59/U 750feet
RG6/U 1,000feet
RG11/U 1,500feet
Power Requirement
12VDC at 1A
24VAC at 500mA
INSTALLATION*
Included with Digital Watchdog Camera:
1. User Manual
2. Mounting Template
3. Security L-Key
4. Single Sided Hex Key
5. Secondary BNC Cable for a Field Monitor
6. Four (4) Screws and Four (4) Dry Wall
Anchors
1
3
2
4
5
7
6
Camera Installation
Use the Mounting Template when mounting the camera.
Use the Security L-Key to loosen the Four Screws that secure the vandal-proof dome cover.
Remove the cover; then, remove the inner screw holes to mount the camera.
NOTE: Keep the lens and the vandal proof cover free from dust or ngerprint.

INSTALLATION*
A. Loosen the Screws (A) with the Security L-Key
included with your camera.
B. Separate the Upper Case (B) from the Base (F).
C. Cut a hole in the ceiling for routing the cables.
D. Use the Mounting Template to drill the four
screw holes on the surface of the ceiling.
E. Pass the Power Cable (C) and the Video Cable (E)
from the camera unit through the hole in the
ceiling.
F. Align the screw holes of the camera unit with
the holes in the ceiling. Secure the four screws.
G. Install and adjust the camera unit.
H. Assemble the Upper Case (B) and the Baes (F).
I. Put the upper case and the base together.
J. Tighten the outer Screws (A) using the Security
L-Key.
INSTALLATION AND ADJUSTMENT*-D2382TIR
Included with DW Indoor Dome Camera:
1. User Manual
2. Mounting Template
3. One Security L-Key
4. One Single Sided Hex Key
5. Secondary BNC Cable for a Field Monitor
6. Two (2) Screws andTwo (2) Dry Wall
Anchors
7. IR Remote Controller
Camera Installation
Use the mounting template to mount the camera.
Using the security L-key to loosen the four screws that secure
the vandal proof dome cover, Remove the vandal proof dome
cover to access the screw holes to mount the camera.
NOTE: Keep the lens and the vandal proof cover free from dust
or ngerprint.
3-Axis Gimbal Adjustment
13
2
4
57
6
1514

CONNECTION*
Video Output BNC Cable
Main Monitor
Field Test Monitor
Spot Monitor Cable
DC12V / AC24V
CAMERA OSD & IR REMOTE CONTROLLER*
NOTE:
Press [KEY] + [ID] (Default is “001”for ID=1)
Press [ENT] to access the Menu
Note: The camera ID is a 3-digitnumber.
Key Button
Menu Access and Control
Zoom Function Control
ID Buttons
Motion Alarm On &OFF
Field Test Monitor Video Output
RS485 Connector
Dip Switch for the IR Remote Controller
Mini Joystick for the Menu Setup
LEFT
UP DOWN
RIGHT
-D2382TIR
1716

1918
LENS ADJUSTMENT*
A. Move the Zoom Lever until you get the desired position.
B. Move the Focus Lever until you get the desired focus.
A. Zoom Lever
B.Focus Lever
: D2362DIR, D2363D, D2363TIR, D2367WD, D2367WTIR, D2382TIR, D2365T
CAMERA SETTING & ON-SCREEN DISPLAY*
Field Test Monitor Video Output
RS485 Connector
Dip Switch for the IR Remote Controller
Mini Joystick for the Menu Setup
LEFT
UP DOWN
RIGHT

2120
MODULE OSD MENU*-D2362DIR
EXPOSURE COLOR DAY&NIGHT
BRIGHTNESS
SHUTTER
BLC
AGC
WB MODE D&N MODE
FUNCTION MOTION PRIVACY
MIRROR
SHARPNESS
GAMMA
SLC
HME
DRC
ALARM MASK 1
MASK 2
MASK 3
MASK 4
COLOR SET
SYNC SETUP EXIT
SYNC CAMERA ID
TITLE EDIT
TITLE RESET
TITLE POSITION
DPC SET
LANGUAGE
PC CONT.
EXIT
SAVE & EXIT
FACTORY RESET
EXPOSURE
BRIGHTNESS MANUAL (ELC LEVEL : 0 ~ 100) / DC (DC LEVEL : 0 ~ 31)
SHUTTER 1/60, 1/100FLC, 1/120 ~ 1/100000
BLC OFF / ON
BLC (Back Light Compensation)
AGC OFF / 12dB ~ 36dB
AGC (Auto Gain Control)
COLOR
WB MODE AWC / ATW / MANuAL / PUSHLOCK
AWC is recommended.
R-Y GAIN 0 ~ 255
B-Y GAIN 0 ~ 255
DAY & NIGHT
Day & Night Mode
AUTO / COLOR / BW
COLOR---->BW : Switching from COLOR to BW; If the number is higher, the camera will only
switch during a super low light condition.
BW ---->COLOR : Switching from BW to COLOR; This number should be always lower than
COLOR to BW
Read Time : time interval to switch from COLOR to BW
COLOR
B&W Mode : (BURST : OFF/ON) When the burst is OFF, the picture will have less noise.
OSD MENU*-D2362DIR

2322
FUNCTION
MIRROR OFF/ MIRROR
SHARPNESS 0 ~ 49
GAMMA USER / 0.45 / 0.6 / 1.00
SLC OFF / ON (0 ~ 50)
SLC (Side Light Compensation)
HME OFF / ON (0 ~ 55)
HME (Highlight Masking Exposure)
DIS OFF /ON
DIS (Digital Image Stabilizer)
MOTION (OMNI-Plus Cameras Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (0 ~ 55)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT(1 ~ 15)
Motion Alarm Zoom-In Delay
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
COLOR SET BLACK / GRAY / COLOR 1~ 6
SYNC
SYNC MODE INTERNAL / AUTO
V-PHASE 0 ~ 199
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT
TITLE RESET
TITLE POS.
DPC OFF / ON
DPC ( Dead Pixel Cancellation)
LANGUAGE English / Chinese
PC CONT. OFF / ON
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default

2524
MODUEL OSD MENU*-D2363D, D2363TIR
EXPOSURE
BRIGHTNESS 0 ~ 100
SHUTTER 1/60 / FLK / 1/250 ~ 10000 / SENS-UP x2 ~ x256
BLC/HME OFF / BLC / HME
AGC HIGH / MIDDLE / LOW / OFF
AGC(Auto Gain Control)
STARLIGHT AUTO(x2 ~ x256) / OFF
NIGHT-UP NORMAL / HIGH
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / AWT / PUSH LOCK / MANUAL / INDOOR / OUTDOOR
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
DAY & NIGHT
Day & Night Mode
AUTO : READ TIME(3~63) / S-LEVEL(0~100) / E-LEVEL(0~100)
COLOR---->BW : B&W : Switching from COLOR to BW; If the number is higher, the camera
will only switch during a super low light condition
BW ---->COLOR : Switching from BW to COLOR; This number should be always lower than
COLOR to BW
Read Time : time interval to switch from COLOR to BW
COLOR
B&W Mode : BURST (OFF / ON) There is less noise when the BURST is OFF.
SMART IR (OFF / ON)
C-SUP Color Suppression :
Color will be reduced at low illumination, if the C-SUP Level is set higher. 0 ~ 63
A-SUP Aperture Suppression : The sharpness of the edges will be reduced at low illumination, if
A-SUP level is set higher. 0 ~ 15
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXPOSURE COLOR DAY&NIGHT
BRIGHTNESS
AE PREFERENCE
BLC / HME
AGC
STARLIGHT
NIGHT-UP
WB MODE
R-Y GAIN
B-Y GAIN
D&N MODE
C_SUP
A_SUP
FUNCTION MOTION PRIVACY
MIRROR
SHARPNESS
GAMMA
FREEZE
NEGATIVE
D-ZOOM
3D DNR
DRC
MOTION PRIVACY
SYNC SETUP EXIT
SYNC TITLE EDIT
PC CONTROL
(RS485 Control)
LANGUAGE
MONITOR
OSD COLOR
OMNI LENS
DEFECT
EXIT
SAVE & EXIT
FACTORY RESET
OSD MENU*-D2363D, D2363TIR

2726
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00
FREEZE OFF / ON
NEGATIVE OFF / ON
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
3D-DNR ON (0~100) / OFF
3D Digital Noise Reduction
DRC OFF / INDOOR / OUTDOOR
Dynamic Range Compressor
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION (OMNI-Plus Camera Only)
MOTION
OFF
ON
AREA SELECT (AREA 1~4)
AREA SET (POSITION / SIZE)
SENSITIVITY (0~40)
MOTION TRACE (OFF / ON)
MOTION VIEW (OFF / ON)
RETURN
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
PRIVACY
PRIVACY
OFF
ON
AREA SELECT (1~8)
AREA SET (POSITION / SIZE)
COLOR (0~15)
RETURN
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / AUTO
EXIT JUMP EXIT / SAVE & EXIT / FACTORY SET
SETUP
TITLE EDIT OFF / ON
PC CONTROL
(RS485 Control)
CAM ID / ID DISPLAY (OFF/ON) / BAUDRATE (2400 / 4800 / 9600)
The protocol is xed pelco-D.
LANGUAGE ENG / KOR / JPN / CHN1 / CHN2 / RUS / FRAN / SPAN / ITAL
MONITOR CRT / LCD
Select LCD only if the camera is directly connected to the LCD monitor.
OSD COLOR 0 ~ 15
OMNI LENS
OFF (OMNI-Plus Camera Only)
ON
ALARM / READ TIME / ALARM ZOOM / STAND BY / RETURN
DEFECT WHITE DEFECT CANCEL MODE
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT
SAVE&EXIT
FACTORY SET

2928
MODULE OSD MENU*-D2367WD, D2367WTIR, D2382TIR
EXPOSURE COLOR DAY&NIGHT
BRIGHTNESS
SHUTTER
BLC
AGC
MAX_DR
STARLIGHT
WB MODE
R-Y GAIN
B-Y GAIN
D&N MODE
C_SUP
A_SUP
FUNCTION MOTION PRIVACY
MIRROR
SHARPNESS
GAMMA
FREEZE
NEGATIVE
3D DNR
D-ZOOM
SLC
HME
DIS
MOTION MASK 1
MASK 2
MASK 3
MASK 4
MASK 5
MASK 6
SYNC SETUP EXIT
SYNC CAMERA ID
TITLE
DPC
MONITOR
LANGUAGE
BAUDRATE
OMNI LENS
EXIT
SAVE & EXIT
FACTORY RESET
OSD MENU*-D2367WD, D2367WTIR
EXPOSURE
LENS DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
SHUTTER 1/60, 1/100FLC, 1/120 ~ 1/100000
BLC OFF / ON
Back Light Compensation
AGC HIGH / MIDDLE / LOW / OFF
Auto Gain Control
MAX-DR OFF /ON (0~ 20) (Electronic Wide Dynamic Range)
STARIGHT OFF / AUTO (x2 ~ x256)
x32 is recommended.
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / ATW / MANUAL / PUSH LOCK
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
DAY & NIGHT
Day & Night Mode
AUTO/ COLOR/ BW / EX-CONT
COLOR---->BW : Switching fromcolor to BW; if the number is higher, the camera will only switch during a
super low light condition.
BW ---->COLOR : Switching from BW to color; this number should always be lower than COLOR to BW
Read Time: Timeinterval to switch from Color to Black-and-White
COLOR
B&W: (BURST:OFF/ON) Whenthe burst is OFF will make less noise
C-SUP Color Suppression :
Color will be reduced at low illumination, if the C-SUP Level is higher. 0 ~ 100 (Not Available
when DNR is On.)
A-SUP ApertureSuppression:
The sharpness of the edges will be reduced at low illumination, if A-SUP Level is higher. 0 ~ 100
(Not Available when DNR is On.)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET

3130
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00 / USER
FREEZE OFF / ON
NEGATIVE OFF/ ON
3D-DNR OFF / LOW / MIDDLE / HIGH
3D Digital Noise Reduction
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
SLC OFF / ON Side Light Compensation
HME OFF / ON
Highlight Masking Exposure
DIS OFF / ON
Digital Image Stabilizer
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION (OMNI-Plus Cameras Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15)
Motion Alarm Zoom-In Delay
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / AUTO
V-PHASE 0 ~ 199
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT OFF / ON
DPC OFF / AUTO
DPC (Dead Pixels Cancellation)
MONITOR CRT / LCD
LANGUAGE English,Japanese, Chinese
BAUDRATE 2400 / 4800 / 9600 / 14400 / 19200 / 38400.
Protocol is Pelco-D(xed cannot be changed;hardcodedinto the DSP)
OMNI LENS OFF / 1 ~ 10 (OMNI-Plus Cameras Only)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default

OSD MENU*-D2382TIR
EXPOSURE
LENS DC (0~100) / MANUAL / VIDEO. (DC Lens is recommended.)
SHUTTER 1/160 /1/100 / FLC / 1/250 ~ 10000 / SENS-UP x2 ~ x250
BLC OFF / ON , BLC (Back Light Compensation)
AGC HIGH / MIDDLE / LOW / OFF
AGC (Auto GainControl)
MAX-DR OFF /ON (0~ 20) (Electronic WideDynamic Range)
STARIGHT AUTO (x2 ~ x250) / OFF (x32 is recommended.)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / ATW / MANUAL / PUSH LOCK
R-Y GAIN 0 ~ 100
B-Y GAIN 0 ~ 100
DAY & NIGHT
Day & Night Mode
AUTO/ COLOR/ BW / EX-CONT
COLOR---->BW : Switching fromcolor to BW; if the number is higher, the camera will only switch during a
super low light condition.
BW ---->COLOR : Switching from BW to color; this number should always be lower than COLOR to BW
Read Time: Timeinterval to switch from Color to Black-and-White
COLOR
B&W: (BURST:OFF/ON) Whenthe burst is OFF will make less noise
C-SUP Color Suppression :
Color will be reduced at low illumination, if the C-SUP Level is higher. 0 ~ 100 (Not Available
when DNR is On.)
A-SUP ApertureSuppression:
The sharpness of the edges will be reduced at low illumination, if A-SUP Level is higher. 0 ~ 100
(Not Available when DNR is On.)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
FUNCTION
MIRROR OFF/MIRROR/V-FLIP/ROTATE
SHARPNESS 0 ~ 31
GAMMA 0.05 ~ 1.00 / USER
FREEZE OFF / ON
NEGATIVE OFF/ ON
3D-DNR OFF / LOW / MIDDLE / HIGH, 3D-DNR (3D Digital Noise Reduction)
D-ZOOM OFF / ON (x1.0 ~ x32 PTZ)
SLC OFF / ON SLC (Side Light Compensation)
HME OFF / ON HME (Highlight Masking Exposure)
DIS OFF / ON
DIS (Digital Image Stabilizer)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION (Omni-Focus Lens Only)
MOTION
OFF / ON
SET WINDOW
ALL SET (Set the Entire Screen)
ALL CLEAR (Clear the Entire Screen)
SENSITIVITY (1 ~ 120)
SHOW INDICATOR (OFF / ICON / TRACE)
DELAY OUT (1 ~ 15)
Motion Alarm Zoom-In Delay
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
Motion Alarm Setup
1. Go to Motion Menu
2. Set Motion to “ON”
3. Click [Set Windows] and set your area of the motion detection
4. Press the Left Arrow button, until you exit back to the Motion Menu
5. Zoom out to the farthest you want the camera to zoom out and press [7](Wide)
6. Zoom in to the farthest you want the camera to zoom in and press [8](Tele)
7. Click [Exit Jump] then click [Save & Exit]
8. Once you are out of the menu press [9](ON/OFF) to activate motion alarm
3332

PRIVACY
MASK 1 OFF / ON
MASK 2 OFF / ON
MASK 3 OFF / ON
MASK 4 OFF / ON
MASK 5 OFF / ON
MASK 6 OFF / ON
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SYNC
SYNC INTERNAL / AUTO
V-PHASE 0 ~ 199
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SETUP
CAMERA ID 0 ~ 255
TITLE EDIT OFF / ON
DPC OFF / AUTO
DPC (Dead Pixels Cancellation)
MONITOR CRT / LCD
LANGUAGE English,Japanese, Chinese
BAUDRATE 2400 / 4800 / 9600 / 14400 / 19200 / 38400.
Protocol is Pelco-D(xed cannot be changed;hardcodedinto the DSP)
OMNI LENS OFF / 1 ~ 10 (for OMNI-PLUS CAMERA only)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT Exit the menu
SAVE&EXIT Exit the menu and save the setting
FACTORY SET Reset the menu setting to factory default
MODULE OSD MENU*-D2365T
EXPOSURE COLOR DAY&NIGHT
BRIGHTNESS
AE PREFERENCE
WDR
BLC
AGC
STARLIGHT
METER ZONE
WB MODE
COLOR GAIN
D&N MODE
FUNCTION MOTION PRIVACY
MIRROR
SHARPNESS
GAMMA
3D DNR
D-ZOOM
MOTION PRIVACY
SYNC SETUP EXIT
SYNC PC CONTROL
TITLE
LANGUAGE
MONITOR
OMNI LENS
FLUORESCENT
DIGITAL VIDEO
OUT
EXIT
SAVE & EXIT
FACTORY RESET
3534

OSD MENU*-D2365T FUNCTION
MIRROR OFF / MIRROR / V-FLIP / ROTATE
SHARPNESS -8 ~ 8
GAMMA 25(0.25) ~ 100(1.0)
3D DNR MOVIE / INFO
D-ZOOM ZOOM:1(x1.0) ~ 12(x8)
PAN(-100~100)/TILT(-100~100) (Digital Zoom/Pan using the camera mini joystick)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
MOTION
MOTION
OFF / ON (ACTIVITY THR (0 ~ 255))
SET MOTION ZONES
- 1 ZONE / 1 ~ 2 ZONE / 1 ~ 3 ZONE / 1 ~ 4 ZONE
- ADJUST ZONE 1 (MOVE/MAKES WIDE/MAKES NARROW)
- ADJUST ZONE 2 (MOVE/MAKES WIDE/MAKES NARROW)
- ADJUST ZONE 3 (MOVE/MAKES WIDE/MAKES NARROW)
- ADJUST ZONE 4 (MOVE/MAKES WIDE/MAKES NARROW)
RETURN
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
PRIVACY
PRIVACY
OFF
ON
- AREA 1 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 2 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 3 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 4 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 5 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
- AREA 6 OFF/ON (MOVE/MAKES WIDE, MAKES NARROW)
RETURN
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
EXPOSURE
BRIGHTNESS -48 ~ 60
AE PREFERENCE OUTDOOR / INDOOR
BLC OFF / BLC (PERCENTILE 10 ~ 50)
WDR LOW / NORMAL / MEDIUM / HIGH / CUSTOM
AGC LOW / MEDIUM / HIGH / CUSTOM
STARLIGHT x2 ~ x64 / OFF
METER ZONE ADJUST ZONE 1 / ADJUST ZONE 2
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
COLOR
WB MODE AWC / ATW(2,000k~11,000K) / PUSH LOCK / MANUAL
(KELVIN:2,000L~11,000K /R/B:RED:-20~20 BLUE:-20~20)
COLOR GAIN -8 ~8
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
DAY & NIGHT
D&N MODE
AUTO / AUTO(EXT) / COLOR / B&W
- AUTO Mode:(READ TIME:0~255/S-LEVEL:0~60/E-LEVEL:0~60/BW AGC:0~60)
- AUTO(EXE) Mode:(Option-IR LED Mode)
- COLOR Mode
- B&W Mode
BW BURST (OFF / ON)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
3736

SYNC
SYNC INT1(SYNC to 59.64Hz)/INT2(SYNC to 60.01Hz)/LL LIMIT/V PHASE/RETURN)
EXIT JUMP EXIT / SAVE&EXIT / FACTORY SET
SETUP
PC CONTROL
CAM ID:1 ~ 255
ID DISPLAY : OFF / ON
PROTOCOL : PELCO-D
BAUDRATE : 2400/4800/9600/19200
RETURN
TITLE OFF / ON
(TITLE/ID POSITION(UP-LEFT/UP-CENTER/UP-RIGHT/DOWN-LEFT/
DOWN-CENTER/DOWN-RIGHT)
LANGUAGE ENGLISH
MONITOR CRT / LCD
OMNI LENS
OFF
ON ALARM OFF
ALARM ON(READ TIME(5~15)/ALARM ZOOM(4~214)/STAND BY(0~214)/RETURN)
FLUORESCENT
OFF / CRR(Manual Lens, Color Rolling/Flickerless Mode)/
CRR2(DC Lens, Color Rolling Mode)
DIGITAL VIDEO OUTPUT
DIGITAL OUT (OFF / ON)
FIELD ORDER (NORMAL / REVERS)
FRAME RPT (OFF / 2X / FREEZE)
RETURN
EXIT JUMP
EXIT / SAVE&EXIT / FACTORY SET
EXIT
EXIT
SAVE & EXIT
FACTORY SET
SPECIFICATIONS*
Model D2362DIR
Camera TYPE Color/BW
Plastic 18IR-LED Day/Night Digital Dome Camera
Mount Surface
Image Size 1/3"
Pixels-Total 811(H) x 508(V)
Pixels-Eective 768(H) x 494(V)
Scanning System 525 line, 2:1Interlace
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination IR-LED On 0.0 Lux
Functions BLC ON / OFF (Area Setting)
AGC ON / OFF (Gain Adjust)
AWB ATW / AWC / MANUAL / PUSH LOCK
DRC ON / OFF
Motion Detection ON / OFF
Privacy Zone 4 Programmable Zone / Size
Lens Focal Length 3.3 ~ 12mm Varifocal Auto Iris Lens
Resolution Horizontal 540 TV Lines [at TDN (B/W) :560 TV Lines]
Video Output VBS 1.0Vp-p VBS 1.0Vp-p(75 Load)
S/N Ratio S/N Ratio 50dB
OSD OSD YES
Environmental Conditions Operating Temperature -10oC~ +55oC(14oF~ 131oF)
Humidity Less than 90%
Power Power Requirement 12VDC
Power Consumption
0.9W, 75mA / 2.9W, 242mA (LED ON)
Physical Specication Dimensions(φ x H) 110.3 X 134.9mm, 4.34 X 5.31in
3938