Digital Watchdog DWC-B1362TIR650 User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
PIPE CAMERA
Double Arm Bracket
DWC-B1362TIR650
DWC-B1363D
DWC-B1363TIR
DWC-B1365T
DWC-B1367WD
DWC-B1367WTIR
DWC-B1367WTIR650
DWC-B2382TIR
11042011

22
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacturer.
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface.
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to Provide reasonable protection against harmful
interference. when the equipment is operated in a residential environment. This equipment generates, uses,
and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications.

3
TROUBLESHOOTING
No VIDEO
Out-of-Focus VIDEO
Before sending your camera for repair, check the following or contact our technical specialist.
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.

4
PART & DESCRIPTIONS*
DWC-B1362TIR650, B1363TIR, B1367WTIR, B1367WTIR650
DWC-B1363D, B1365T, B1367WD
1
11
3
910
12
13
2
4
56
7
8
1Front Case
2Zoom, Focus Housing
3Sunshield
4Lens
5Rear Case
6Control Board
7Con Cap
8Double Arm Bracket
9BNC Jack
Assembly Screw
Fixing Screw
Set Screw
10 Power Input Connector
DC 12V / AC24V Voltage
11
12
13
RS 485
OPTION
B1367WD
B1367WTIR
B1367WTIR650
No IR
IR

5
DWC-B2382TIR
1
2
89
10
3
45
6
7
1Front Case
2Sunshield
3Lens
4Rear Case
5Control Board
6Con Cap
7Double Arm Bracket
8BNC Jack
9
10
Power Input Connector
Assembly Screw
Fixing Screw
RS 485 (EK:D+, WH:D-)
DC 12V / AC24V Voltage
11
12
Set Screw
13
11 12
13

6
DIMENSIONS IN MILLIMETERS*
DWC-B1362TIR650, B1363TIR, B1367WTIR, B1367WTIR650
DWC-B1363D, B1365T, B1367WD
No IR
IR

7
DWC-B2382TIR

8
INSTALLATION*
Included with DW Pipe Camera
1. User Manual
2. Mounting Template
3. Four(4) Screw and Four(4) Dry Wall Anchors
4. 2nd Video Jack
5. Tool
6. L-Wrench
7. IR Remote Controller
1
2
3 4 5
6 7 DWC-B2382TIR

9
NOTE : Screws required electrical junction boxes are not supplied. These
screws are readily acailable at well-stocked electrical supply store.
MOUNTING ON ELECTRICAL JUNCTION BOX*
NPT 3/4” Pipe

10
CONNECTING TO MONITORS*
Follow the diagram below to make proper connections to the CRT Monitor or the Monitor.
12VDC/24VAC
Monitor
30cm
CCTV Monitor
2nd Video Output
RightLeft
Up
Down
Power connection - 12VDC/24VAC Dual Voltage(Auto polarity detection and protection)
All camera are equipped with a service monitor output on the camera module.