Digital Watchdog DWC-D3263WTIR User manual

Quick Start Guide Quick Start Guide
1. The mounting surface must withstand five times the weight of your
camera.
2. Pay attention to the cables. The can easily become caught and
damaged. Any damage may cause a short or fire.
3. Detach the camera’s dome cover by pressing on both sides of the
dome cover.
4. Use the mounting template to mark and drill the necessary holes in
the mounting surface.
STEP 1 – PREPARING TO MOUNT THE CAMERA
Pass the wires through the mount bracket and make all necessary
connections. Connect the BNC cable and power cables to the camera.
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
Power Requirements Power Consumption
DC12V / AC24V dual-voltage
DC12V (LED o): 2.94W
DC12V (LED on): 5.22W
AC24V (LED o): 2.5W
AC24V (LED on): 4.35W
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
DWC-D3263WTIR
Protective sheet
Protective pad
WHAT’S IN THE BOX
Screws
and plastic
anchors-
2pcs
1 Set Mounting
template 1
Test video
cable 1Quick set up guide 1
DC plug
cable
Manual
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut
Screw &
Plasc Anchor-2pcs
Torx Wrench
Test Video Cable
Manual
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut
Screw &
Plasc Anchor-2pcs
Torx Wrench
Test Video Cable
Manual
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut
Screw &
Plasc Anchor-2pcs
Torx Wrench
Test Video Cable
Manual
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut
Screw &
Plasc Anchor-2pcs
Torx Wrench
Test Video Cable
Attention: This document is intended to serve as a quick reference for initial
set up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in
the ‘Search by Product’ search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick set up guide (QSGs) will appear in the results.
DW® Universal HD over Coax®
indoor dome cameras

Quick Start Guide
1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:
a. Remove the camera’s dome to access the joystick and OSD
control on the base of the camera.
b. Use the OSD Switch to switch the camera’s signal.
1. Once all cables have been connected, use the screws included with
the camera to properly mount and secure the camera to the mounting
surface.
2. Adjust the camera’s pan, tilt and position to achieve the desired view.
The cameras’ max angles are:
Pan: 0° ~ 360°
Tilt: 0° ~ 70°
Rotation: 0° ~ 360°
STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN
THE CAMERA
Rev Date: 08/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Rotation 360°
Titling 70°
Panning 360°
- To switch the camera to
HD-TVI mode, press OSD
joystick to the left
for 5 seconds.
- To switch the camera to
HD-Analog mode, press OSD
joystick to the right
for 5 seconds.
- To switch the camera to CVBS
mode, press OSD joystick up
for 5 seconds.
- To switch the camera to
HD- CVI mode, press OSD
joystick down for 5 seconds.
FOCUS
ZOOM
1
2
3
OSD joystick controller
3. To adjust the camera’s focus and zoom:
a. Unlock the zoom or focus screws by rotating them
counter-clockwise.
b. Adjust the zoom and focus screws at the base of the camera
module to achieve a clear image.
c. Tighten the screws and close the front case by rotating it
clock-wise.
4. Once the installation is complete, remove the protective film from the
camera’s dome cover.