Digital Watchdog MEGApix DWC-MB72I4V User manual

DWC-MB72I4V
Step 1 – PREPARING TO MOUNT THE CAMERA
Step 3 – INSTALLING THE CAMERA
Step 2 – CABLING THE CAMERA TO EXTERNAL
DEVICES
1. The mounting surface must bear ve times the weight of your
camera.
2. Do not let the cables get caught in improper places or the electric
line cover to be damaged. This may cause a breakdown or re.
3. Using the mounting template sheet or the camera itself, mark and
drill the necessary holes in the wall or ceiling.
5. To use the camera’s water proof wiring:
(1).Install the LAN cable into (a).
(2).(b) will be assembled to (a) with a 1/4 turn.
(3).Thread (c) tightly to (b).
6. Before mounting the camera, loosen the pan/tilt screw on the side
of the camera’s bracket. This will make adjustment after mounting
the camera easier.
7. Fix the camera on to the mounting surface using the screws
included with the camera.
8. Adjust the camera’s pan and tilt. Tighten the pan/tilt screw on the
camera’s bracket until it is secured properly.
4. Pass the wires through the mount bracket and make all necessary
connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch,
connect the camera using an Ethernet cable for both data and
power.
b. NETWORK CONNECTIONS – If you are using a non-PoE
switch, connect the camera to the switch using an Ethernet
cable for data transmission and use a power adapter to power
the camera.
NETWORK
CONNECTION
POWER
1
2
3
Template
Sheet
Quick Start Guide Quick Start Guide
Username: admin Password: admin
Attention: This document is intended to serve as a quick reference page for
initial set-up. It is recommended that the user read the entire instruction
manual for complete and proper camera usage.
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
WHAT’S IN THE BOX
QSG Manual 1 Set
Manual CD 1 Set
Template Sheet 1 Set
Screw & Plastic Anchor – 4pcs 1 Set
Torx Wrenc h 1 Set
Note: To ensure moisture seal, make sure the o-ring is in place
between (a) and (b). In extreme environments use of an
outdoor rated sealer is recommended.
Resetting the camera: To reset the camera, use the tip of
a paper clip or a pencil and press the reset button. Pressing
the button for ve (5) seconds will initiate a camera-wide reset
of all the settings, including network settings.
a
b
cPan/Tilt
Screw
8
Power Requirements Power Consumption
DC 12V
PoE IEEE 802.3atPoE+ / PoE Class 2
LED Off: 1.92W, 160mA
LED On: 2.7W, 230mA (IR models only)
Reset
Button

Step 5 – WEB VIEWER
Once the camera’s network settings have been setup properly,
you can access the camera’s web viewer using the DW IP Finder™.
To open the camera’s web viewer:
1. Find the camera using the DW IP Finder™.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website’. The camera’s web viewer
will open up in your default web browser.
4. Enter the camera’s username and password (default are
admin / admin).
5. If you are accessing the camera for the rst time, install the
VLC les in order to view video from the camera.
4. The camera’s default network information is:
Network Setup
1. Run the CD included with the camera and click on the DW IP Finder™le.
2. The software will scan your network for all supported cameras and display the results in the table. Allow up to 5 seconds for the IP Finder to nd the camera
on the network.
3. Select a camera from the list by double-clicking on the camera’s image or clicking on the ‘Click’ button under the IP Conf. column. The camera’s network
information will appear. If necessary, you can adjust the camera’s network type.
Select DHCP if the internet service is dynamic IP. This will allow the camera to receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask, Gateway and DNS information.
Contact your network administrator for more information.
Default TCP/IP information
• IP: 192.168.1.80
• Subnet Mask: 255.255.255.0
• Ga t eway : 192.16 8 .1.1
• DN S: 16 8.126.6 3.1
6. To save the changes made to the camera’s settings, input the ID
and PW of the camera for authentication and click ‘Save’.
7. If the camera needs to be rebooted after the settings were
changed, press the ‘Reboot’ button. The camera will cycle power
and will appear back in the search results once the reboot is
complete.
5. To view the camera’s web viewer, click on ‘View Camera Website’.
‘Port Forwarding’ has to be set in your network’s router for
external access to the camera.
Default ID / PW : admin / admin
Rev Date: 8/15 © 2015 Digital Watchdog. All rights reserved.
Note: Please see the full product manual for web viewer setup,
functions and camera settings options.
Step 4 – DW IP FINDER™
Use the DW IP Finder™included in the camera’s accessory CD to scan the network and detect all MEGApix®cameras, set the camera’s network settings,
perform rmware upgrade or access the camera’s web client.
DWCMF10M28T
DWCMF21M4TIR
DWCMF10M28T
DWCMF21M4TIR
Firmware Upgrade Open Camera's IP
Conguration Screen
Camera Uptime
Camera Name,
Model, IP Address,
and MAC Address
Camera's Firmware
Search for
Cameras
View Camera's
Thumbnail View
Camera's Network Settings
Filter Search
Results
Quick Start Guide