Digital Watchdog MEGAPIX DWC-MF5Wi4TWDMP User manual

5MP model 2.1MP/1080p model
DWC-MF5Wi4TWDMP DWC-MF2Wi4TWDMP
Attention: This document is intended to serve as a quick reference page for
the initial setup. It is recommended that the user read the entire instruction
manual for complete and proper camera usage.
Tel: [phone]
Technical Support Hours:
9:00 AM – 8:00 PM EST, Monday through Friday
digital-watchdog.com
WHAT’S IN THE BOX
Quick Setup
and Download
guides
1 set Moisture
Absorber 1 set
Star Wrench 1
Mounting
Bolt and
Nuts - 2pcs
1 set
Mounting
Template for
Bolt and Nuts
Installation
1
Screws and
Plastic
Anchors –
3pcs
1 set
Mounting
Template for
Plate
Installation
1Mounting
Plate 1
Quick Start Guide Quick Start Guide
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’ search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
STEP 2 – POWERING THE CAMERA
Pass the wires through the mount bracket and make all necessary
connections.
1. NETWORK CONNECTIONS – If you are using a PoE Switch, connect
the camera using an Ethernet cable for both data and power.
2. NETWORK CONNECTIONS – If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.
Part number Power Requirements Power Consumption
DWC-MF5Wi4TWDMP
DC 12V, PoE IEEE 802.3af
Class 3
(Adapter not included).
DC12V: max 5.9W
PoE: max 7.2W
DWC-MF2Wi4TWDMP
DC 12V, PoE IEEE 802.3af
Class 2
(Adapter not included).
DC12V: max 4.0W
PoE: max 5.5W
1. The mounting surface must withstand five times the camera weight.
2. Do not let the cables get caught in improper places or the electric line
cover can be damaged. This may cause a short or fire.
3. CAUTION: These servicing instructions are for use by qualified
service personnel only. To reduce the risk of electric shock do not
perform any servicing other than that contained in the operating
instructions unless you are qualified to do so.
4. This product is intended to be supplied by a UL Listed Power Supply
Unit marked “Class 2” or “LPS” or “PS2” and rated 12 Vdc, 0.49A
(DWC-MF5Wi4TWDMP) and 0.33A (DWC-MF2Wi4TWDMP) min.
5. The wired LAN hub providing power over the Ethernet (PoE) in
accordance with IEEE 802-3af shall be a UL Listed device with the
output evaluated as a Limited Power Source as defined in UL60950-
1 or PS2 as defined in UL62368-1.
6. Unit is intended for installation in a Network Environment 0 as
defined in IEC TR 62102. As such, associated Ethernet wiring shall
be limited to inside the building.
7. For the installation process, remove the dome cover from the
camera module by loosening the three (3) screws on the dome. Use
the wrench provided with the camera.
8. Install the moisture packet in the base of the camera’s lens.
a. Remove the moisture absorber from
the packaging.
b. Cut the card and folder along
the dotted line.
c. Place the moisture absorber
around the camera’s lens module.
STEP 1 – PREPARING TO MOUNT THE CAMERA
Reset Button
Poron Ring
9. Remove the protective film
between
the dome and the camera module.
10. Remove the Poron Ring before
placing the dome back on the
camera. When attaching the dome
back, align the line on the dome
with
the one on base of the camera.
11. Using the mounting template sheet
or the camera itself, mark and drill
the necessary holes in the wall or
ceiling.

Quick Start Guide
Rev Date: 08/20
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
NOTE: Please refer to DMP guide for additional information on integration
and camera control.
1. Attach the main body to the mount bracket by tightening the
lock screw.
2. For soft installation surfaces, use the included metal mount plate.
Fix the mount plate on the mounting surface using the included
screws. Then, press the bottom case onto the mount plate. The
three bezels on the case will align and snap lock onto the plate.
3. To use the camera’s waterproof wiring:
a. Install the LAN cable into .
b. will be assembled
to with a 1/4 turn.
c. Thread tightly to .
Resetting the camera: To reset
the camera, use the tip of a paper
clip or a pencil and press the reset
button. Pressing the button for five
(5) seconds will initiate a
camera-wide reset of all
the settings, including
network settings.
a
b
c
STEP 3 – INSTALLING THE CAMERA
a
a
b
bc
NOTE: To ensure moisture seal, make sure the o-ring is in place
between and . In extreme environments use of an
outdoor rated sealer is recommended.
ab
NOTE: When using the waterproof cap, crimp the RJ45
connector after passing the cable through the
waterproof cap.
Reset Button
Poron Ring
Protective Film
4. Once the installation is complete, adjust the camera’s tilt, panning
and rotation as needed. The cameras’ max angles are:
Pan: 0° ~ 360°
Tilt: 0° ~ 70°
Rotation: 0° ~ 360°
5. Assemble the dome cover over the camera body and detach the
protecting film from the dome bubble.
Mounting Template STEP 3 – INSTALLING THE CAMERA (CONT.)
Installation using Mount Bolt and Screws:
1. Using the mounting template, mark and drill the holes on the
mounting surface.
2. Secure the two long mounting screws to the camera’s base.
3. Pass the wires through the mount bracket and make all
necessary connections.
4. Mount the camera to the mounting surface by using the 2 mounting
nuts. Rotate the locking discs over the screws until the camera is
held tightly from the mounting surface.