Digital Watchdog DWC-D3563WTIR User manual

Quick Start Guide Quick Start Guide
1. The mounting surface must withstand five times the weight of
your camera.
2. Do not let the cables get caught in improper places or the electric
line cover can be damaged. This may cause a short or fire.
3. Detach the camera’s dome cover by pressing on the two small
buttons located at each side of the cover dome.
4. Remove the dome protection film before placing the dome back
on the camera base.
STEP 1 – PREPARING TO MOUNT THE CAMERA
Pass the wires through the mount bracket and make all
necessary connections. Connect the BNC cable and power
cables to the camera.
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
Power
Requirements Power Consumption
DC12V/AC24V
dual voltage
DC12V (LED o): 3.3W (275mA)
DC12V (LED on): 5.9W (495mA)
AC24V (LED o): 2.75W (200mA)
AC24V (LED on): 5.3W (360mA)
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
DWC-D3563WTIR
WHAT’S IN THE BOX
DC plug
cable 1 Set
Screws
and plastic
anchors
(2pcs)
1 Set
Template
sheet 1 Set Quick Setup Guide 1 Set
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
ManualTemplate Sheet Screw & Moisture absorber &
Absorber Guide
Sunshield cover &
Protection sticker
Protection film
Attention: This document is intended to serve as a quick reference for
initial set-up. It is recommended that the user read the entire instruction
manual for complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in
the ‘Search by Product’ search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.

Quick Start Guide
1. The camera supports HD-Analog, HD-CVI and HD-TVI signals. To
switch between the signals:
a. Enter the camera’s OSD menu. You can access it locally from
using the camera’s joystick in the body of the camera, or from a
recorder supporting UTC communication. Go to SETUP >
OUTPUT > ANALOG MODE.
b. Set the camera’s analog signal output from the following
options:
• HD-A: supports 5MP/1944p @ 20fps and 12.5fps, 4MP/1440p
@ 30fps, 2.1MP/1080p @ 30fps and 720p @ 30fps.
• HD-T: supports 5MP/1944p @ 20fps, 4MP/1440p @ 30fps,
2.1MP/1080p @ 30fps and 720p @ 30fps.
• HD-C: supports 4MP/1440p @ 30fps, 2.1MP/1080p @ 30fps
and 720p @ 30fps.
• CVBS: supports up to 960H @ 30fps
c. Change CONFIRM to ON to save the changes.
d. Go to the EXIT menu and select SAVE&EXIT to save all changes.
The camera signal automatically.
1. Once all cables have been connected, use the screws included
with the camera to properly mount and secure the camera to the
mounting surface.
2. Adjust the camera’s pan, tilt and position to achieve the desired
view. The cameras’ max angles are:
Pan: 0° ~ 360°
Tilt: 0° ~ 70°
Rotation: 0° ~ 360°
3. To adjust the camera’s focus and zoom:
a. Unlock the zoom or focus screws by rotating them
counter-clockwise.
b. Adjust the zoom and focus screws at the base of
the camera module to achieve a clear image.
c. Tighten the screws and close the front case
by rotating it clock-wise.
4. Once the installation is complete, remove the protective film from
the camera’s dome cover.
STEP 4 – INSTALLING THE CAMERASTEP 3 – CHANGING THE SIGNAL IN
THE CAMERA
Rev Date: 06/19
Copyright © Digital Watchdog. All rights reserved.
Specifications and pricing are subject to change without notice.
Focus
Zoom