Digital Watchdog INFINITY 960H DWC-B1567WD User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
960H Outdoor Bullet Camera
Double Arm Bracket
11192012
DWC-B1567WD
DWC-B1567WTIR

22
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacturer.
Do not open or modify.
Do not open the case except during maintenance and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential environment. This equipment generates, uses,
and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction
manual, it may cause harmful interference to radio communications.

3
Table of Contents
Introduction
Installation
Camera OSD Menu and Glossary
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Included Accessories
Easy Installation
Control Board _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Connecting to Monitors _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
4
5
6
7
8
10
9
13-29
30
31-32
33-34
Adjusting the Lens 11
Camera Setting Angle 12

4
FEATURES*
DWC-B1567WD / DWC-B1567WTIR
1/3” 960H High Resolution CCD
700 TV Lines
3.3~12mm Varifocal Auto Iris Lens
True Day and Night (DWC-B1567WTIR only)
Star-Light (Super Low Light Technology)
EWDR (Electronic Wide Dynamic Range)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
Negative Imaging
Mirror Image Control
RS485 Built-in
Programmable Privacy Zones (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
100ft Range IR with Intelligent Camera Sync (B1567WTIR only)
IP66 Certified, No Fog or Condensation

5
1
11
3
910
12
13
2
4
56
7
8
1Front Case
2Zoom, Focus Housing
3Sunshield
4Lens
5Rear Case
6Control Board
7Control Cap
8Double Arm Bracket
9BNC Jack
Assembly Screw
Fixing Screw
Set Screw
10 Power Input Connector
DC 12V / AC24V Voltage
11
12
13
RS 485
No IR
IR
PART & DESCRIPTIONS*

6
DIMENSIONS IN MILLIMETERS (INCHES)*
No IRIR
230(9.05”)
86.5(3.40”)
122(4.80”) 96.5(3.79”)
68.0(2.67”)
86.5(3.40”)
78.0(3.07”)
5(0.19”)
96.0(3.77”)

7
1. User Manual
2. Mounting Template
3. Four (4) Screws and Four (4) Dry Wall Anchors
4. Second Video Jack
5. Tool
6. L-Wrench
 


INSTALLATION*

8
EASY INSTALLATION*
Use the 4 mounting screws to install the camera on the
wall or ceiling.
Then, follow the next step on the pages 9-12.
NPT 3/4” Pipe

*Installation Using a Junction Box
*Note: Electrical junction box and required screws sold separately.

9
CONNECTING TO MONITORS*
12VDC/24VAC
Monitor
30cm
CCTV Monitor
2nd Video Output
RightLeft
Up
Down
Power Connection - 12VDC/24VAC Dual Voltage (Auto polarity detection and protection)
All cameras are equipped with a service monitor output on the camera module.

10
CONTROL BOARD*
Joystick
Secondary Connector
[1] Joystick -
Controls the OSD menu.
[2] Secondary Connector -
Tests video output connector.
To Access Control Board:
[1] Remove clear plastic ring from the
control cap.
[2] Turn Control Cap counter-clockwise
until cap separates completely from the
camera body.
Functions: