Digital Watchdog DWC-D4365T User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
SNAP-IT
Indoor Dome Camera
DWC-D4363D
DWC-D4363TIR
DWC-D4367WD
DWC-D4367WTIR
DWC-D4382TIR
DWC-D4365T
03022011

2
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacture.
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface.
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
Provide reasonable protection against harmful interference. when the equipment is
operated in a residential environment. This equipment generates, uses, and radiates
radio frequency energy; and if it is not installed and used in accordance with the
instruction manual, it may cause harmful interference to radio communications.

3
TROUBLESHOOTING
No VIDEO
Out-of-Focus VIDEO
Before sending your camera for repair, check the following or contact our technical specialist.
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.

4
PART & DESCRIPTIONS*
1
Lens
3UTP
4RS 485
2
Power Input Connctor
12VDC/24VAC Dual Voltage
6
Video Output Connector - BNC
5
10
2nd Video Connector
9
Camera Control Board
7
Bubble
8
Upper Case
Mounting Screws
NOTE : These assembly screws located on the dome
cover and not with mounting hardware.
2
3
4
8
10
6
7
1
9
5
NO IR IR
C
O
M
M
O
N

5
INSTALLATION*
Included with DW Indoor Dome Camera
1. User Manual
2. Mounting Template
3. Two(2) Screw and Two(2) Dry Wall Anchors
4. 2nd Video Jack
5. IR Remote Controller
1
2
3
4
5
DWC-D4382TIR

6
DIMENSIONS IN MILLIMETERS*
89
108
Surface Mount Indoor
TOP VIEW
40,5
56,3
96,8
108

7
BASE INSTALLATIONS*
OSD
Philips #8-32 x 0.75
Surface Mount
1
22S
NO IR IR

8
MOUNTING ON ELECTRICAL JUNCTION BOX*
NOTE : Screws required for electrical junction boxes are not supplied.These
screws are readily available at well-stocked electrical supply store.
Philips #8-32 x 0.75
2S
NO IR IR

9
CONNECTING TO MONITORS*
Power Connection - 12V DC / 24V AC Dual Voltage(Auto Polarity Detection and Protection)
All cameras are equipped with a 2nd video output on the camera Main Board.
DC 12V / AC 24V
CCTV Monitor
Monitor
300.0
2nd Video Output
Up
Down
Left Right
NO IR
IR

10
ADJUSTING THE VARI-FOCAL DC AUTO IRIS LENS*
Follow the instructions provided below to make any lens adjustments
1Loosen the Zoom & Focus screws.
2Using the screw, move it RIGHT or LEFT to the desired position.
3Once the desired adjustments have been made, tighten the screw to lock in place.
4Adjust the Field of View by moving the screw towards the RIGHT(Tele) to zoom in, or
towards the LEFT(Wide) to zoom out.
5Adjust the Focus the same way as described above after the desired zoom position is
estabilished.
NO IR IR
ZOOM
FOCUS
Zoom:
Focus:
Tele - Wide
Far - Near
DWC-D4363D
DWC-D4367WD
DWC-D4365T
DWC-D4363TIR
DWC-D4367WTIR
DWC-D4382TIR

11
ADJUSTING 3-AXIS GIMBAL*
The Gimbal mechanism yields maximum rotation and placement ad show below.
1Rotation 360 3Panning 360
NO IR IR NO IR IR
2Tilting 90
NO IR
4Tilting 82
IR

12
FEATURES*
1/3” Sony Super HAD ⅡCCD
560 TV Lines
3.3~12mm Varifocal Auto Iris Lens
Electronic Day and Night
Star-Light (Super Low Light Technology)
3D-DNR (3D Digital Noise Reduction)
DRC (Dynamic Range Compressor)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
32X Digital Zoom / Negative Imaging
UTP / RS485 Built-In
Programmable Privacy Zone(8) & Motion Detection(4)
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
D4363D
D
4
3
6
3
D

13
MODULE OSD MENU*
PRIVACY RGB
BRIGHTNESS
SHUTTER
BLC / HME
AGC
STARLIGHT
NIGHT-UP
EXPOSURE
SYNC
SYNC
D&N MODE
C_SUP
A_SUP
DAY&NIGHT
PRIVACY
PRIVACY
PC CONTROL
(RS485 Control)
TITLE EDIT
LANGUAGE
MONITOR
OSD COLOR
OMNI LENS
DEFECT
SETUP
R-Y GAIN
B-Y GAIN
WB MODE
COLOR
MIRROR
SHARPNESS
FREEZE
GAMMA
NEGATIVE
D-ZOOM
3D DNR
DRC
FUNCTION
EXIT
SAVE & EXIT
FACTORY RESET
EXIT
MOTION
MOTION

14
EXPOSURE
COLOR
DAY & NIGHT
BRIGHTNESS
SHUTTER
BLC/HME
AGC
AWC / AWT / PUSH LOCK / MANUAL / INDOOR / OUTDOOR
R-Y GAIN
WB MODE
B-Y GAIN
EXIT JUMP
Day & Night Mode
C_SUP
A_SUP
EXIT JUMP
STARLIGHT
NIGHT-UP
EXIT JUMP
0 ~ 100
1/60 / FLK / 1/250 ~ 10000 / SENS-UP x2 ~ x256
OFF / BLC / HME
0 ~ 100
0 ~ 100
Color Suppression : Color will be reduced at low illumination, if the C-SUP Level is set higher.
0 ~ 63
AUTO : READ TIME(3~63) / S-LEVEL(0~100) / E-LEVEL(0~100)
COLOR
B&W Mode : BURST (OFF / ON) There is less noise when the BURST is OFF.
SMART IR (OFF / ON)
COLOR▬► B&W:SwitchingfromCOLORtoBW;Ifthenumberishigher,thecamerawillonlyswitchduringasuperlowlightcondition
B&W ▬► COLOR:SwitchingfromBWtoCOLOR;ThisnumbershouldbealwayslowerthanCOLORtoBW
ReadTime:timeintervaltoswitchfromCOLORtoBW
0 ~ 15
HIGH / MIDDLE / LOW / OFF
AGC(Auto Gain Control)
AUTO(x2 ~ x256) / OFF
NORMAL / HIGH
EXIT / SAVE&EXIT / FACTORY SET
EXIT / SAVE&EXIT / FACTORY SET
EXIT / SAVE&EXIT / FACTORY SET
Aperture Suppression : The sharpness of the edges will be reduced at low illumination, if A-SUP level is set higher.

15
MIRROR
SHARPNESS
GAMMA
FREEZE
NEGATIVE
D-ZOOM
3D DNR
DRC
EXIT JUMP
OFF / MIRROR / V-FLIP / ROTATE
0 ~ 31
0.05 ~ 1.00
OFF / ON
OFF / ON
OFF / ON (x1.0 ~ x32 PTZ)
ON (0~100) / OFF
3D Digital Noise Reduction
OFF / INDOOR / OUTDOOR
Dynamic Range Compressor
EXIT / SAVE&EXIT / FACTORY SET
EXIT / SAVE&EXIT / FACTORY SET
EXIT / SAVE&EXIT / FACTORY SET
FUNCTION
MOTION
PRIVACY
EXIT JUMP
EXIT JUMP
OFF
ON
AREA SELECT (AREA 1~4)
AREA SET (POSITION / SIZE)
ON
AREA SELECT (1~8)
AREA SET (POSITION / SIZE)
COLOR (0~15)
RETURN
SENSITIVITY (0~40)
MOTION TRACE (OFF / ON)
MOTION VIEW (OFF / ON)
RETURN
MOTION (OMNI-Plus Camera Only)
PRIVACY
OFF

16
SYNC
EXIT JUMP
INTERNAL / LINE
EXIT / SAVE&EXIT / FACTORY SET
SYNC
TITLE EDIT
PC CONTROL
(RS485 Control)
LANGUAGE
MONITOR
OSD COLOR
OMNI LENS
EXIT JUMP
DEFECT
EXIT
SAVE & EXIT
FACTORY RESET
OFF / ON
CAM ID / ID DISPLAY (OFF/ON) / BAUDRATE (2400 / 4800 / 9600)
The protocol is fixed pelco-D.
ENG / KOR / JPN / CHN1 / CHN2 / RUS / FRAN / SPAN / ITAL
CRT / LCD
Select LCD only if the camera is directly connected to the LCD monitor.
0 ~ 15
OFF (OMNI-Plus Camera Only)
ON
ALARM / READ TIME / ALARM ZOOM / STAND BY / RETURN
WHITE DEFECT CANCEL MODE
EXIT / SAVE&EXIT / FACTORY SET
SETUP
EXIT

17
SPECIFICATIONS*
MODEL
General Spec NTSC PAL
CCD Type 1/3" 410K Pixels Color 1/3" 470K Pixels Color
Total num ber of pixels 811(H) X 508(V) 795(H) X 596(V)
Minimum Illumination
Resolution
Pow er Consum ption
General Spec NTSC PAL
Shutter speed 1/60s - 1/100,000s 1/50s - 1/100,000s
S/N Ratio
Gamma
Sync System
Operation Temperature
Storage Temperature
Operation Humidity
DWC-D4363D
0.14Lux (F1.2, 30IRE-COLOR)
0Lux (LED ON)
560 TV Lines (COLOR)
580 TV Lines (BW)
Electric Spec
COMMON
52dB or More(AGC OFF)
0.45
Internal / Line Lock
Voltage
Mechanical Spec
-10℃∼+50℃ (14�F ~ 131�F)
-20℃∼+70℃
Under 90% (Non-condensing)
AC 24[V] (20.0[V] ~ 30.0[V])
DC 12[V] (11.0[V] ~ 20.0[V])
DC 12V: 2.3W / AC 24V: 2.5W

18
FEATURES*
D4363TIR
1/3” Sony Super HAD ⅡCCD
560 TV Lines
3.3~12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync
TDN (True Day and Night / TDN5)
Star-Light (Super Low Light Technology)
DRC (Dynamic Range Compressor)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
AGC / BLC / AWB
32X Digital Zoom / Negative Imaging
UTP / RS485 Built-In
Programmable Privacy Zone(8) & Motion Detection(4)
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
D
4
3
6
3
T
I
R

19
MODULE OSD MENU*
PRIVACY RGB
BRIGHTNESS
SHUTTER
BLC / HME
AGC
STARLIGHT
NIGHT-UP
EXPOSURE
SYNC
SYNC
D&N MODE
C_SUP
A_SUP
DAY&NIGHT
PRIVACY
PRIVACY
PC CONTROL
(RS485 Control)
TITLE EDIT
LANGUAGE
MONITOR
OSD COLOR
OMNI LENS
DEFECT
SETUP
R-Y GAIN
B-Y GAIN
WB MODE
COLOR
MIRROR
SHARPNESS
FREEZE
GAMMA
NEGATIVE
D-ZOOM
3D DNR
DRC
FUNCTION
EXIT
SAVE & EXIT
FACTORY RESET
EXIT
MOTION
MOTION

20
EXPOSURE
COLOR
DAY & NIGHT
BRIGHTNESS
SHUTTER
BLC/HME
AGC
AWC / AWT / PUSH LOCK / MANUAL / INDOOR / OUTDOOR
R-Y GAIN
WB MODE
B-Y GAIN
EXIT JUMP
Day & Night Mode
C_SUP
A_SUP
EXIT JUMP
STARLIGHT
NIGHT-UP
EXIT JUMP
0 ~ 100
1/60 / FLK / 1/250 ~ 10000 / SENS-UP x2 ~ x256
OFF / BLC / HME
0 ~ 100
0 ~ 100
Color Suppression : Color will be reduced at low illumination, if the C-SUP Level is set higher.
0 ~ 63
AUTO : READ TIME(3~63) / S-LEVEL(0~100) / E-LEVEL(0~100)
COLOR
B&W Mode : BURST (OFF / ON) There is less noise when the BURST is OFF.
SMART IR (OFF / ON)
COLOR▬► B&W:SwitchingfromCOLORtoBW;Ifthenumberishigher,thecamerawillonlyswitchduringasuperlowlightcondition
B&W ▬► COLOR:SwitchingfromBWtoCOLOR;ThisnumbershouldbealwayslowerthanCOLORtoBW
ReadTime:timeintervaltoswitchfromCOLORtoBW
0 ~ 15
HIGH / MIDDLE / LOW / OFF
AGC(Auto Gain Control)
AUTO(x2 ~ x256) / OFF
NORMAL / HIGH
EXIT / SAVE&EXIT / FACTORY SET
EXIT / SAVE&EXIT / FACTORY SET
EXIT / SAVE&EXIT / FACTORY SET
Aperture Suppression : The sharpness of the edges will be reduced at low illumination, if A-SUP level is set higher.