Digital Watchdog Snapit DWC-V4363D User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
SNAP-IT
Outdoor Dome Camera
DWC-V4363D
DWC-V4363TIR
DWC-V4367WD
DWC-V4367WTIR
DWC-V4382TIR
DWC-V4365T
DWC-V4363DH
DWC-V4382TIRH
03022011

2
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacture.
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface.
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
Provide reasonable protection against harmful interference. when the equipment is
operated in a residential environment. This equipment generates, uses, and radiates
radio frequency energy; and if it is not installed and used in accordance with the
instruction manual, it may cause harmful interference to radio communications.

3
TROUBLESHOOTING
No VIDEO
Out-of-Focus VIDEO
Before sending your camera for repair, check the following or contact our technical specialist.
Check the coaxial cable and make sure it is connected securely.
Check the lens’ iris adjustment at the menu setup of the camera.
Check the power supply and make sure the camera has the proper voltage and current.
Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean.
Check the lens manual focal and zoom adjustment. Field test monitor is recommended.

4
PART & DESCRIPTIONS*
C
O
M
M
O
N
1
3
Lens
2
Power Input Connector
DC 12V /AC 24V Voltage
UPT
4
RS 485
5
Video Output Connector - BNC
6
Camera Control Board
7
Bubble
8
Upper Case
9
Flush Mount Case
10
Surface Mount Case
11
Assembly Screws
#8 - 32 x 0.75
12
2nd Video Connector
13
Safety Wire
14
Mounting Screws
2
3
4
10
9
6
14
11
7
8
1
13
12
5
NO IR IR

5
INSTALLATION*
Included with DW Outdoor Dome Camera
1. User Manual
2. Mounting Template
3. Four(4) Screw and Four(4) Dry Wall Anchors
4. L-Wrench
5. TORX-T20 Bolt
6. 2nd Video Jack
7. DC Plug
8. Tool
9. IR Remote Controller
DWC-D4382TIR
DWC-D4382TIRH
1
3 4 5
6 7 98
2

6
DIMENSIONS IN MILLIMETERS*
139
101
137
17
28
54
98,8
121
118,8
139
36
29
53,8
121
Flush Mount
Top View
Surface Mount

7
BASE INSTALLATIONS*
Remove the dome cover by loosening the 3 screw located at the Lid(Upper).
Vandal dome uses the torx screws. Use the supplied Torx Wrench.
Surface Mount
Using four ST4X35 screws provided, mount the surface mount plate to a sturdy
surface. Using three screws, fix flush mount base to the surface mount plate.
Flush Mount
Using four ST4X35 screws supplied, mount the surface mount plate to a sturdy
surface.
2
1
3
T20 M4 X 16
Plastic Anchors
ST4X35
ST #8 - 32 x 0.75
Surface Mount Flush Mount
NO IR NO IRIR IR

8
MOUNTING ON ELECTRICAL JUNCTION BOX*
NOTE : Screws required for electrical junction boxes are not supplied.These
screws are readily available at well-stocked electrical supply store.
Designed for both flush mount or surface mount applications, pre-drilled mounting holes
on EasyView dome accommodate various electrical junction boxes, making installation
easy and less time consuming.
When mounting the flush mount base, surface mount plate, or both together, use the
pre-drilled holes marked with the symbol for proper installation.
Screws UNC 8-32 x 0.75
NPT 3/4” Pipe
4S 4S
NO IR IR

9
CONNECTING TO MONITORS*
Power Connection - 12V DC / 24V AC Dual Voltage(Auto Polarity Detection and Protection)
All cameras are equipped with a 2nd video output on the camera Main Board.
Follow the diagram below to make proper connections to CRT Monitor or the Monitor.
DC 12V / AC 24V
CCTV Monitor
Monitor
300.0
2nd Video Output
Up
Down
Left Right
NO IRIR

10
ADJUSTING THE VARI-FOCAL DC AUTO IRIS LENS*
Follow the instructions provided below to make any lens adjustments.
1Loosen the Zoom & Focus screws.
2Using the screw, move it RIGHT or LEFT to the desired position.
3Once the desired adjustments have been made, tighten the screw to lock in place.
4Adjust the Field of View by moving the screw towards the RIGHT(Tele) to zoom in, or
towards the LEFT(Wide) to zoom out.
5Adjust the Focus the same way as described above after the desired zoom position is
estabilished.
Zoom:
Focus:
Tele - Wide
Far - Near
Focus
Zoom
NO IRIR
DWC-V4363TIR
DWC-V4367WTIR
DWC-V4382TIR
DWC-V4382TIRH
DWC-V4363D
DWC-V4367WD
DWC-V4365T
DWC-V4363DH