Digital Watchdog PTZ39XFM User manual

Super Speed Dome
PTZ39X with In-Ceiling Mount
Version 1.00
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
User’s Manual
PTZ39XFM

Safety Information
Y
This symbol indicates that dangerous voltage
consisting a risk of electric shock is present within
this unit.
Warning Precaution
This exclamation point symbol is intended to alert the
user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (BACK). THERE ARE NO USER
SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION:
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or
moisture.
Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could
cause fire, electrical shock, or damage to the product.
Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage
to the product.
Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat generation
or fire.
Securely plug the power cord into the power receptacle. Insecure connection may cause fire.
When installing the camera, fasten it securely and firmly. A falling camera may cause personal injury.
Do not place conductive objects (e.g. screw drivers, coins, metal objects) or containers filled with water on top
of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects.
Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.
If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect
the power sorce and contact the service center. Continued use in such a condition may cause fire or electric
shock.
If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this
product in any way.
When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.
WARNING
WARNING
1.
2.
3.
4.
5.
6.
7.
8.
9.

Safety Information
Z
Operating
tBefore using, make sure power supply and others are properly connected.
tWhile operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and
then contact your Special dealer.
Handling
tDo not disassemble or tamper with parts inside the camera.
tDo not drop or subject the camera to shock and vibration as this can damage the camera.
tCare must be taken when you clean the clear dome cover. Scratch and dust will ruin the quality of the camera.
Installation and Storage
tDo not install the camera in areas of extreme temperature, which exceed the allowable range.
tAvoid installing in humid or dusty places.
tAvoid installing in places where radiation is present.
tAvoid installing in places where there are strong magnetic elds and electric signals.
tAvoid installing in places where the camera would be subject to strong vibrations.
tNever expose the camera to rain or water.
PRECAUTION

[
1. Read these instructions.
2. Keep these instructions for future reference.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this camera near water.
6. Clean only with a dry cloth. Unplug the camera from the wall outlet before cleaning.
7. Do not block any ventilation openings to ensure reliable operation of the product ad to protect it from
over-heating. Install in accordance with the manufacturer’s instructions.
8. Do not install the camera near any heat sources such as radiators, heat registers, or other apparatus that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an
electrician for a replacement.
10. Protect the power cord from being walked on or pinched particularly at or near plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specied by the
manufacturer or sold with the apparatus. Unplug this camera when
a cart is used. Use caution when moving the cart that contains the
camera to avoid injuries that can result from the camera falling over.
13. Unplug the camera during lightning storms or when it is not being used for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power supply cord or plug is damaged, liquid has been spilled on the camera, objects have
fallen into the camera, the camera has been exposed to rain or moisture, the camera does not operate normally,
or the camera has dropped.
Safety Instructions

Contents
\
6
7
Product & Accessories
Part Name
1. Introduction
8
10
14
DIP Switch Setup
Installation
Cabling
2. Installation
16
17
18
19
20
21
22
24
26
28
29
30
32
34
36
38
39
41
Check Points Before Operation
Functions
OSD DIsplay of Main Screen
General Rules of Menu Operation
ROOT MENU > SYSTEM INFORMATION
DISPLAY SETUP > CAMERA ID
DISPLAY SETUP > PRIVACY ZONE
MOTION SETUP
FUNCTION SETUP > PRESET SETUP
FUNCTION SETUP > SCAN SETUP
FUNCTION SETUP > PATTERN SETUP
FUNCTION SETUP > GROUP SETUP
FUNCTION SETUP > SCHEDULE SETUP
CAMERA SETUP > WB SETUP
CAMERA SETUP > AE SETUP
CAMERA SETUP > SPECIAL
SYSTEM SETUP
SYSTEM INITIALIZE
3. OSD
42
43
Dimension
Specification PTZ39XFM
4. Specifications

]
Product & Accessories
Introduction -
1
CD with
User’s Manual
Product Accessories
Quick Start Guide
Dome Cover
In-Ceiling Housing
with PTZ Mechanism
Safety Wire X2

^
Part Name
Introduction -
1
Dome Cover Hooks
Dome Cover
Dome Cover Side Hole
PTZ Mechanism
PTZ Mechanism Hook
In-Ceiling Housing
PTZ Mechanism Hook Guide
Mounting Clip
In-Ceiling Housing Border
Mounting Clip Bolt
Housing Safety Wire Hanger
Junction Box
Junction Box Hook
Junction Box Cover
Junction Box Cover Side Hole

_
DIP Switch Setup
Installation -
2
Before installing the camera, you should
set the DIP switch to configure the
camera ID (Communication Protocol).
Inner Box
1. Communication Protocol Setup
Congure the appropriate protocol with DIP switch using the
DIP switch combination.
- If you set the protocol as AUTO protocol, camera
will
automatically recognize the type of protocol being used;
however, this will not recognize the AD protocol.
- If you want to control the camera using the DVR or system
keyboard,
the protocol must be identical to the camera
protocol. Otherwise, you will not bwe able to control the
camera.
- If you change the camera protocol by adjusting the DIP
switch, the change will be eective after you reboot the
camera.
Protocol Setup Baud Rate Setup RS-485
Termination Resistor
ON
8J
21 345678
1AUTO - Factory Default
ON
8J 21345678
2
ON
8J 21345678
PELCO-D
3
ON
8J 21345678
PELCO-P
4
5
6
7
SAMSUNG
ON
21345678
PANASONIC
8J
ON
21345678
GE (Kalatel)
8J
ON
21345678
AD (American Dynamics)
ON
8J 21345678

`
DIP Switch Setup
Installation -
2
2. Communication Baud Rate Setup
Select the appropriate baud rate with DIP switch combination.
4. Camera ID Setup
ID number of camera is set using binary number.
The example is shown below.
Inner Box
1
2
3
4
5
ON
8J 21345678
2400 BPS - Factory Default
ON
8J 21345678
4800 BPS
ON
8J 21345678
9600 BPS
ON
8J 21345678
19200 BPS
38400 BPS
ON
8J 21345678
3. RS-485 Termination Resistor
- Pin 8 is used to control RS-485 termination.
- Normally, it must be set to OFF state.
- When you have trouble with long daisy chain style
connection, turn ON this termination switch for the last camera.
ON
8J
21 345678
Pin 1234 56 78
1 2 4 8 16 32 64 128ID Value
ex) ID=5
ex) ID=10
ON
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
- If you want to control the camera with another device, you
must match the Camera ID with CAM ID, setting on DVR or
the keyboard controller.
- ID number of the camera is set using binary number.
- The range of ID is 0~255.
- Factory default of camera ID is 1.
- Camera ID will be effective without rebooting the camera.

XW
Installation
Installation -
2
2
1
3
DETACH PTZ MECHANISM AND JUNCTION BOX COVER
By pressing down and holding up the hooks located on
both sides of the PTZ Mechanism, detach PTZ Mechanism
from the housing. Then, detach the junction box cover by
pressing down the hooks on both sides of the junction
box.
DRILL THE HOLE ON THE CEILING
To install the in-ceiling housing in the ceiling, first drill a
190mm diamter hole on the ceiling.
HOOK THE SAFETY WIRES
Connect one of the rings for the safety wire with the housing
safety wire hanger to prevent the junction box cover from
falling down. Then, connect the other ring with the hanger
bolt of the ceiling.