Digital Watchdog MEGApix DWC-MB82i4V User manual

DWC-MB82i4V
Step 1 – PREPARING TO MOUNT THE CAMERA
Step 3 – INSTALLING THE CAMERA
Step 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
1. The mounting surface must bear ve times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover to
be damaged. This may cause a breakdown or re.
3. Using the mounting template sheet or the camera itself, mark and drill the
necessary holes in the wall or ceiling.
5. To use the camera’s water proof wiring:
(1).Install the LAN cable into (a).
(2).(b) will be assembled to (a)
with a 1/4 turn.
(3).Thread (c) tightly to (b).
6. Before mounting the camera, loosen the pan/tilt screw on the side of the
camera’s bracket. This will make adjustment after mounting the camera easier.
7. Fix the camera on to the mounting surface using the screws included with the
camera.
8. Adjust the camera’s pan and tilt. Tighten the pan/tilt screw on the camera’s
bracket until it is secured properly.
4. Pass the wires through the mount bracket and make all necessary connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch, connect the
camera using an Ethernet cable for both data and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch, connect
the camera to the switch using an Ethernet cable for data transmission and
use a power adapter to power the camera.
Power Requirements
DC 12V
PoE IEEE 802.3atPoE+ / PoE Class 2
Power Consumption
LED Off: 1.92W, 160mA
LED On: 2.7W, 230mA (IR models only)
NETWORK
CONNECTION
POWER
1
2
3
Template
Sheet
Quick Start Guide Quick Start Guide
Username: admin Password: admin
Attention: This document is intended to serve as a quick reference page for initial set-up.
It is recommended that the user read the entire instruction manual for complete and proper
camera usage.
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
WHAT’S IN THE BOX
QSG Manual 1 Set Screw & Plastic
Anchor – 3pcs 1 Set
Manual CD 1 Set Tor x Wrench 1 Set
Template Sheet 1 Set
Note: To ensure moisture seal, make sure the o-ring is in place between
(a) and (b). In extreme environments use of an outdoor rated sealer
is recommended.
Resetting the camera: To reset the camera, use the tip of a paper clip or
a pencil and press the reset button. Pressing the button for ve (5) seconds
will initiate a camera-wide reset of all the settings, including network settings.
a
b
c
Reset
Button
Pan/Tilt
Screw
8

Step 5 – WEB VIEWER
Once the camera’s network settings have been setup properly, you can access the
camera’s web viewer using the DW IP Finder™. To open the camera’s web viewer:
1. Find the camera using the DW IP Finder™.
2. Double-click on the camera’s view in the results table.
3. Press the ‘View Camera Website’. The camera’s web viewer will open up in
your default web browser.
4. Enter the camera’s username and password (default are admin / admin).
5. If you are accessing the camera for the rst time, install the VLC les in
order to view video from the camera.
Quick Start Guide
4. The camera’s default network information is:
Network Setup
1. Run the CD included with the camera and click on the DW IP Finder™le.
2. The software will scan your network for all supported cameras and display the
results in the table. Allow up to 5 seconds for the IP Finder to nd the camera on
the network.
3. Select a camera from the list by double-clicking on the camera’s image or
clicking on the ‘Click’ button under the IP Conf. column. The camera’s network
information will appear. If necessary, you can adjust the camera’s network type.
Select DHCP if the internet service is dynamic IP. This will allow the camera to
receive its IP address from the DHCP server.
Select STATIC to manually enter the camera’s IP address, subnet mask,
Gateway and DNS information.
Contact your network administrator for more information.
Default TCP/IP information
• IP: 192.168.1.80
• Subnet Mask: 255.255.255.0
• Gate way: 192.16 8.1.1
• DNS: 16 8.126 .63 .1
6. To save the changes made to the camera’s settings, input the ID and PW of the
camera for authentication and click ‘Save’.
7. If the camera needs to be rebooted after the settings were changed, press the
‘Reboot’ button. The camera will cycle power and will appear back in the search
results once the reboot is complete.
5. To view the camera’s web viewer, click on ‘View Camera Website’.
‘Port Forwarding’ has to be set in your network’s router for external access
to the camera.
Default ID / PW : admin / admin
Rev Date: 03/16
Copyright © Digital Watchdog. All rights reserved. Specifications
and pricing are subject to change without notice.
Note: Please see the full product manual for web viewer setup, functions
and camera settings options.
Step 4 – DW IP FINDER™
Use the DW IP Finder™included in the camera’s accessory CD to scan the network
and detect all MEGApix®cameras, set the camera’s network settings, perform
rmware upgrade or access the camera’s web client.
DWCMF10M28T
DWCMF21M4TIR
DWCMF10M28T
DWCMF21M4TIR
Firmware Upgrade Open Camera's IP
Conguration Screen
Camera Uptime
Camera Name,
Model, IP Address,
and MAC Address
Camera's Firmware
Search for
Cameras
View Camera's
Thumbnail View
Camera's Network Settings
Filter Search
Results