Digital Watchdog DWC-V4567WD User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
960H SNAP-IT
Outdoor Dome Camera
DWC-V4567WD
DWC-V4567WTIR
12132012

2
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacturer.
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning :
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface :
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a residential environment. This equipment generates, uses, and radiates
radio frequency energy; and if it is not installed and used in accordance with the
instruction manual, it may cause harmful interference to radio communications.

3
Table of Contents
Introduction
Installation
Camera OSD Menu and Glossary
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Included Accessories
Easy Installation
Mounting Installation
UTP System
4
5
6
7
8
9-13
14
18-34
35
36-37
38-39
Connecting to Monitors 15
Adjusting the Camera 16
Adjusting the 3-Axis Gimbal 17

EATURES*
4
F
DWC-V4567WD/ DWC-V4567WTIR
1/3” 960H High Resolution CCD
700 TV Lines
3.3~12mm Varifocal Auto Iris Lens
70ft Range IR with Intelligent Camera Sync [V4567WTIR Only]
True Day and Night [V4567WTIR Only]
Star-Light (Super Low Light Technology)
EWDR (Electronic Wide Dynamic Range)
3D-DNR (3D Digital Noise Reduction)
HME (Highlight Masking Exposure)
AGC / SMART BLC / AWB
Night-Up
Negative Imaging
Mirror Image Control
UTP / RS485 Built-in
Programmable Privacy Zones (6) & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Auto Sensing 12VDC or 24VAC with Line Lock
Secondary Video-BNC Output
IP68 Certified (Waterproof)

5
PART & DESCRIPTIONS*
1
3
Lens
2
Power Input Connector
DC 12V /AC 24V Voltage
UTP
4
RS 485
5
Primary Video-BNC Output Connector
6
Camera Control Board
7
Bubble Dome Cover
8
Upper Case
9
Flush Mount Case
10
Surface Mount Case
11
Assembly Screws
#8 - 32 x 0.75
12
Secondary Video-BNC Output Connector
13
Safety Wire
14
Mounting Screws
2
3
4
10
9
6
14
11
7
8
1
13
12
5
NO IR IR

6
DIMENSIONS IN MILLIMETERS (INCHES)*
Flush Mount Top View
Surface Mount
137(5.39”)
101(3.97”)
17(0.66”)
28(1.10”)
54(2.12”)
98.8(3.88”)
139(5.47”)
139(5.47”)
118.8(4.67”)
36(1.41”)
29(1.14”)
53.8(2.11”)
121(4.76”)
121(4.76”)

7
INSTALLATION*
Included with Outdoor Dome Camera
1. User Manual
2. Mounting Template
3. Second Video Jack
4. Four (4) Screws and Four (4) Dry Wall Anchors
5. L-Wrench
6. TORX-T20 Bolt
7. DC Plug
8. TORX-T20 Wrench
1234
5678

8
EASY INSTALLATION*

9
9
SURFACE MOUNT INSTALLATION INSTRUCTIONS*
DC 12V
AC 24V
UTP
RS485
1. Use the camera’s mounting
template or your camera to
mark the holes as required.
2. Drill holes into the drywall and
insert the drywall mounts into
the holes.
3. Pull wires through and make
connections.
If you need to keep the wiring within the
within the camera
housing, refer to the diagram below.
4. Mount the surface mount
base (junction box) to the
wall.
5. Snap the camera module onto
the base by aligning the red
and black markings on the
base and the camera module.

10
6. Secure the three (3) assembly
screws.
7. Adjust the camera’s position
by using the 3-Axis Gimbal.
8. Tighten the three locking
screws with the L-Wrench
to secure the cover dome
over the camera.
Flush Mount Installation
For a flush mount housing, remove the surface mount base
(junction box). Cut a large hole on a flat surface for the top part
of the flush mount base. Use the three screws fixed to the base
to secure it to the surface of the wall or ceiling.
Follow steps 6 through 8 of the Surface Mount Installation
Instructions to complete the installation.
3
ST4X35