Digital Watchdog DWC-PTZ10x User manual

INSTRUCTION MANUAL
DWC-PTZ10x
Mini SPEED DOME CAMERA

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
2/49
This lightning flash with arrowhead symbol is intended to alert the user to
the presence of un-insulated "dangerous voltage" within the product's
enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to individuals.
This exclamation point symbol is intended to alert the user of the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
3/49
Important Safeguard
1. Read Instructions
Read all of the safety and operating instructions before using the product.
2. Retain Instructions
Save these instructions for future reference.
3. Attachments/ Accessories
Do not use attachments or accessories unless recommended by the manufacturer as they may cause
hazards, damage product and void warranty.
4. Water and Moisture
Do not use this product near water or moisture. (Indoor Version)
5. Installation
Do not place or mount this product in or on an unstable or improperly supported location.
Improperly installed product may fall, causing serious injury to a child or adult, and damage to the
product. Use only with a mounting device recommended by the manufacturer, or sold with the
product. To insure proper mounting, follow the manufacturer's instructions and use only mounting
accessories recommended by manufacturer.
6. Power source
This product should be operated only from the type of power source indicated on the marking label.
Precautions
Operating
Before using, make sure power supply is properly connected.
While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your dealer.
Handling
Do not disassemble or tamper with parts inside the camera.
Do not drop or subject the camera to shock and vibration as this can damage camera.
Care must be taken when you clean the clear dome cover. Scratches and dust will ruin your
quality of the picture.
Installation and Storage
Do not install the camera in areas that exceed the allowable temperature range. (Indoor Version)
Avoid installing in humid or dusty places (Indoor Version)
Avoid installing in places where radiation is present.
Avoid installing in places where there are strong magnetic fields and electric signals.
Avoid installing in places where the camera would be subject to strong vibrations.
Never expose the indoor version camera to rain and water.
NOTICE

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
4/49
○
1Introduction
Features 5
Product&Accessories 7
Parts&Functions 8
○
2Installation
DIPSwitchSetup 9
DirectInstallationontheCeiling 11
InstallationusingFlushMountRingBracket 12
InstallationusingCeilingMountBracket 13
InstallationusingWallMountBracket 14
Cabling 15
○
3Operation
CheckingBeforeOperation 17
PresetandPatternFunctionPre-Check 17
Start OSD Menu 18
Reserved Preset 18
Preset 19
Group 19
Pattern 20
Group 21
Schedule 22
Other Functions 23
OSD Display of Main Screen 24
○
4How to use OSD Menu
General Rules of Menu Operation 25
Main Menu 25
Display Setup 26
Privacy Zone Mask Setup 27
Motion Setup 28
Function Setup 30
Preset Setup 31
Group Setup 33
Pattern Setup 34
Group Setup 35
Schedule Setup 37
Camera Setup 38
System Setup 40
System Initialize 41
○
5Specifications
42
Dimension 43
CONTENTS

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
5/49
Features
Camera Specifications
Sensor: ¼“ Super-HAD II CCD
520TVL [Color] 570TVL
Lens: 10x Digital, 10x Optical Zoom (3.8 ~38mm)
360Continuous Pan Rotation
SSNR Digital Noise Reduction
Zoom Magnification: 10 Optical Zoom, 10 Digital Zoom (Max 100 Zoom) [To be Delete]
Function: True Day & Night Function (Moving IR Cut Filter)
Focus Mode: Auto / Manual / Semi-Auto
Auto Sensing, Multiprotocol Receiver
Multi-language Menu-Setup: [English / Spanish / Portuguese / French / Italian / Polish
/Dutch]
Independent or General Camera Characteristic Setup in Preset operation
24VAC/12VDC Power Input
Powerful Pan/Tilt Functions
Max. 360/sec high speed Pan/Tilt Motion
Using Vector Drive Technology, Pan/Tilt movements are accomplished using the shortest
path theory. As a result, time to target view is reduced dramatically and the video on the
monitor is very natural to watch.
For jog operation using a controller, since ultra slow speed 0.05/sec can be reached, it is
very easy to position the camera to the desired target view.
Proportional Pan/Tilt automatically reduces or increases the pan/tilt speed in proportion to
the mount of zoom. At telephoto zoom settings, the pan/tilt speeds will be slower for a given
amount of joystick deflection than at wide zoom settings. This function keeps the image
from moving too fast on the monitor when there is a large amount of zoom
Preset, Pattern, Scan, Group, Privacy Mask, Schedule and More…
127 Presets are assignable and characteristics of each preset can be set up independently,
such as White Balance, Auto Exposure, Label and so on.
8 Scans can be stored. This enables to move camera repetitively between two preset positions
at designated speeds.
4 Pattern are memorized to repeat a series of Pan/Tilt, Zoom, and Preset functions that can
be recalled with a command or automatically by a programmed function (Alarm, Schedule, or
Power-Up)
INTRODUCTION 1

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
6/49
8 Groups are memorized to repeat a series of Presets, Patterns, and Scans. Each group can be
stored 20 entities of Preset/Pattern/Group functions. This function enables the dome camera
to move in combinations of those functions repetitively.
4 Privacy Zone Masks can be programmed. The Masked Zones can be set anywhere in the
viewing area and can be any size.
7 Schedules can be assigned by day and time. Appropriate actions (such as Home, Preset,
Group, Pattern, Scan) can be defined for each rule. Also, it is possible to schedule these
customer settings by daily and weekly requirements.
PTZ (Pan/Tilt/Zoom) Control
RS-485 control, max. 256 cameras can be controlled at the same time. [To Be Delete]
Pelco-D/ Pelco-P /Samsung protocol can be selected as a control protocol in the current
version of firmware. (Using the small Dip-switch at the back of the dome camera)

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
7/49
OSD (On Screen Display) Menu
OSD menu is provided to display the status of camera and to configure the functions
interactively.
There are currently 7 Languages that are supported in the OSD Menu:
[ENGLISH/ESPAÑOL/FRANÇAIS/DEUTSCH/ITALIANO/РУССКИЙ/PORTUGUÊS]
The information such as Camera ID, Pan/Tilt/Zoom/Direction, and Alarm Input & Output,
date/time, current temperature and Preset can be displayed on screen.
Each display item can be turned On or Off independently.
Alarm I/O Functions
2 alarm sensor Inputs and 1 relay output are available.
To protect from external electric noise and shock, the alarm sensor Input is decoupled by
using photo coupler diode.

If an external sensor is activated, camera can be set to move to the corresponding Preset
position.
Relay output can be assigned to work with a certain preset.
Reserved Presets for Special Purpose
In addition to the standard 127 presets, direct calling of reserved presets allows users to set
up many of the camera functions with or without using OSD menu. For more information,
refer to “Reserved Preset” in this manual.
In addition to 127 Presets from 1 to 128 can be assigned excluding preset 95 is reserved for
Main Menu Setup
INTRODUCTION 1

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
8/49
Product & Accessories
Main Product & Accessories
MainBody Surface Mount Bracket
Accessory
Manual Terminal Block
Torque Screw Driver
INTRODUCTION 1
INTRODUCTION

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
9/49
Main Product
MainBody Sun Shield Housing
Accessory
Terminal Block Torque Screw Driver
Manual
Options
Pendant Mount Bracket Wall Mount Bracket
INTRODUCTION 1

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
10/49
Parts Name & Functions
Main Unit / Surface Mount Bracket Back of Main Unit
Surface Mount Bracket This is used to install the camera directly on the ceiling. After
separating the cover attach this directly to ceiling. Camera must be
assembled at the last stage.
Do not use this bracket when installing camera on the wall with
wall mount bracket or on the ceiling with ceiling mount bracket.
Separating Slit Using a coin, you can separate upper part lower body of the dome.
Dome Cover Do not detach protective vinyl from dome cover before finishing
the installation process to protect dome cover from scratches or
dust.
DIP Switch Adjusts camera ID and protocols.
Cable Duct When you want to install the camera on the surface of hard ceiling,
you need to handle the cable through side of the dome. In this
case, break the side wall bit and feed the cable through the cable
duct.
INTRODUCTION 1
Surface
Mount Bracket
Mounting Hole
Main Body
Lockup Screw
Dome Cover
Cabling
Ter m ina l Bl a ck
Prototol&Braud-rate
Dip switches

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
11/49
DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure the camera ID, Baud rate,
and communication protocol.
ID Setting (1~255)
Protocol Buad Rate
RS-485
Terminate
0x00 : 2400
0x01 : 4800
0x02 : 9600
0x03 : 19200
0x04 : 38400
0x00 : Auto Select
0x01 : Pelco-D
0x02 : Pelco-P
0x03 : SAMSUNG
0x04 : VCLTP
0x05 : KD6
Camera ID Setup
123456
ON
ON
78
ID number of camera is set using binary number. The example
is shown below.
SW 1 2 3 4 5 6 7 8
ID Value 1 2 4 8 16 32 64 128
ex) ID=5 on off on off off off off off
ex) ID=10 off on off on off off off off
The range of ID is 0~255. Factory default of Camera ID is 1.
If you want to control a certain camera, you must match the
camera ID with Cam ID setting of DVR or Controller.
INSTALLATION 2

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
12/49
Communication Protocol Setup
123456
ON
ON
78
Communication Baud rate Setup
123456
ON
ON
78
RS-485 Termination Resistor
123456
ON
ON
78
RS-485 Termination Resistor (On/Off)
Select the appropriate Protocol with DIP switch combination.
Switch State
Protocol
SW-1 SW-2 SW-3 Sw-4
OFF OFF OFF OFF Auto Protocol
ON OFF OFF OFF PELCO-D
OFF ON OFF OFF PELCO-P
ON ON OFF OFF SAMSUNG
If you set the protocol as Auto Protocol, camera will
automatically recognize the type of Protocol.
Auto Protocol supports Pelco-D and Samsung Protocol.
If you want to control using DVR or system keyboard, their
protocol must be identical to camera. Otherwise, you cannot
control the camera.
If you changed camera protocol by changing DIP S/W, the
change will be effective after you reboot the camera.
Factory default of protocol is “Auto Protocol”
INSTALLATION 2
Pin 8 is used for ON/OFF of RS-485 Termination. Normally, it
must be OFF state. Especially when you have trouble with long
Daisy chain style connection, turn ON this termination switch of
last camera.
Pin 8
Select the appropriate Baud rate with DIP switch combination.
Switch State
Protocol
SW-5 SW-6 SW-7
OFF OFF OFF 2400 BPS
ON OFF OFF 4800 BPS
OFF ON OFF 9600 BPS
ON ON OFF 19200 BPS
OFF OFF ON 38400 BPS
Factory default of Baud rate is “9600 BPS”

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
13/49
Installation using Surface mount on the Ceiling
In ceiling mount
INSTALLATION 2
1. Pass the cables from the camera unit through the
ceiling mount bracket. Then, connect video,
communication, and power cables.
2. Install surface mount bracket to the ceiling using the
four screws.
3. Align the four screw holes in the camera unit with the
screw holes in the ceiling mount bracket. Then, secure
the camera in place by tightening the four screws.
4. Carry out the settings and adjustments for the
camera.
5. Secure the dome cover by tightening with screws.

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
14/49
Surface mount
INSTALLATION
1. Pass the cables from the camera unit through surface
mount bracket.
Then connect Video, communication, and power cables.
2. Install surface mount bracket to the ceiling usingthe
four screws.
3. Align the four screw holes in the camera unit with the
screw holes in the Surface mount bracket.
Then, secure the camera in place by tightening the
four screws.
4. Carry out the settings and adjustments for the camera.
5. Secure the dome cover by tightening with screws.

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
15/49
Installation using Pendant Mount Bracket
INSTALLATIONINSTALLATION
1. Pass the cables from the camera unit through the pendant
mount bracket.
Then connect Video, communication, and power cables.
2. Install pendant mount bracket to the ceiling using the four screws.
3. Align the four screw holes in the camera unit with the screw
holes in the Pendant mount bracket.
Then secure the camera in place by tightening the four screws.
4. Carry out the settings and adjustments for the camera.
5. Secure the dome cover by tightening with screws.

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
16/49
Installation using Wall Mount Bracket
INSTALLATION 2
1. Pass the cables from the camera unit through the wall
mount bracket.
Then connect Video, communication, and power cables.
2. Install wall mount bracket on the wall using the four screws.
3. Attach the main unit to the wall mount bracket with the four
screws.
4. Carry out the settings and adjustments for the camera.
5. Secure the dome cover by tightening with the screws.

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
17/49
Cabling
Dual Voltage
DC12V/AC24V
Controller/DVR
BNC Video
Cabling Terminal Block
PWR(+)
PWR(-)
F.G
RS-485(+)
RS-485(-)
VIDEO(+)
VIDEO(-)
IN COM
IN1
IN2
Relay Out
Relay Out
Relay Out
Sensors
Monitor
Dual Voltage
DC12V/AC24V
Controller/DVR
BNC Video
Cabling Terminal Block
PWR(+)
PWR(-)
F.G
RS-485(+)
RS-485(-)
VIDEO(+)
VIDEO(-)
IN COM
IN1
IN2
Relay Out
Relay Out
Relay Out
Sensors
MonitorMonitor
INSTALLATION 2
Monitor
1 (Black): IN-COM
2 (Yellow): IN1
3 (Brown): IN2
4 (Red): Relay Out
5 (Orange): Relay Out
RS-485
D-
D+
BNC Video
Dual Voltage
DC12V/AC24V
Sensors
Relay Out
Controller/DVR
MonitorMonitor
1 (Black): IN-COM
2 (Yellow): IN1
3 (Brown): IN2
4 (Red): Relay Out
5 (Orange): Relay Out
RS-485
D-
D+
BNC Video
Dual Voltage
DC12V/AC24V
Sensors
Relay Out
Controller/DVR
1 (Black): SENSOR COM
2 (Brown): SENSOR1
3 (Red): SENSOR2
4 (Orange): Relay COM
5 (Yellow): Relay NO
SENSOR COM
SENSOR1
SENSOR2
Relay COM
Relay NO
V I D E O ( Y E L L O W )
P O W E R I N
V C C ( R E D )G
N D ( B L A C K )
A L A R M C A B L E
R S 4 8 5
D + ( B L A C K )
D - ( W H I T E )
S O L D E R I N G

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
18/49
Power Connection
Please, check the voltage and current capacity of rated power carefully. Rated power is indicated
in the back of main unit.
Power Mode Input Voltage Range
Power Consumption
While in Normal
operation
While Heater
in operation
DC 12V DC 11V ~ 24V 14 W(MAX) 26W(MAX)
AC 24V AC 20V ~ 28V 9W(MAX) 23W(MAX)
 RS-485 Communication
For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same
time, RS-485 communication lines are connected in parallel as shown below.
INSTALLATION 2

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
19/49
Video Connection
Connect with BNC coaxial cable.
Alarm Input Connection
Sensor Input
It is noted that short circuit between GND and Input pin means alarm activation.
If you want to use Alarm Input, the types of sensor must be selected in OSD menu. The sensor
types are Normally Open and Normally Closed. If sensor type is not set properly, the alarm can
be activated reversely.
Normally Open (N.O) Sensor output is turned ON when sensor is activated
Normally Closed (N.C) Sensor output is turned OFF when sensor is activated
Relay Output
There are 4 Alarm Outputs and all of them are Relay contact type. Therefore, you do
not have to care about polarity, AC/DC, and isolations between channels. Care must be
taken to connect relay power as shown above.
INSTALLATION 2
SENSOR1
SENSOR2
SENSOR COM
INTERNAL
Relay COM
Relay NO

DWC-PTZ10x [Mini SPEED DOME CAMERA
]
www.Digital-Watchdog.com
20/49
Check Points Before Operation
Before power is connected, please check the cables carefully.
The camera ID of the controller must be identical to that of the camera to be controlled. The camera
ID can be checked in the System Information screen of the OSD Menu.
If your controller supports multi-protocols, the protocol must be changed to match the camera.
If you changed camera protocol by changing DIP switch, the change will be effective after you reboot
the camera.
Since the operation method can be different for each controller available, refer to the manual for
your controller if camera can not be controlled properly.
Preset and Pattern Function Pre-Check
Review Operating instructions for Preset, Group, Scan and Pattern function programming with
controller or DVR prior to using camera. (refer to your System keyboard Manual)
If controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For
more information, refer to “Reserved Preset” in this manual.
OPERATION 3