Digital Watchdog DWC-V5661T User manual

07212014
ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Starlight MPA
Vandal Dome Camera
DWC-V5661T
DWC-V5661TIR

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of a kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth wi h a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference, when the equipment is operated in a residen ial environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

3
TABLE OF CONTENTS
Introduction
Installation
Module OSD Menu
Troubleshooting
Warranty Information
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Surface Mount Installation
Accessories Installation
Connecting to Monitors
Control Board
4
5
6
7
8
9-12
13
14
17-29
30
31-32
33-34
Adjus ing the Camera Gimbal 16
Adjus ing the Camera Lens 15

4
FEATURES*
1/3" Sony 1.3M CMOS
820 TV Lines [B/W], 800 TV Lines [Color]
2.8~12mm Varifocal Auto Iris Lens
100ft Range IR with Intelligent Camera Sync, Smart IR [DWC-V5661TIR]
True Day & Night with IR Cut Filter
3D DNR (3D Digital Noise Reduction)
WDR (Wide Dynamic Range)
Star-Light (Super Low Light Technology)
HME (Highlight Masking Exposure)
Defog (Extreme Weather Image Copmensation)
Digital Quick Zoom & 8x Digital Zoom
16:9 and 4:3 Viewing Modes
AGC / BLC / AWB
Privacy Zones (16) & 4 Motion Detection Zones
Camera Control via RS-485/ UTC
RS485 & UTP Built-In
RS485, UTP, & 1 Alarm Output Built-In
IP66 Certified (Weatherproof)

5
PARTS & DESCRIPTION*
7
8
9
10
11
1BNC Cable
DC12V Cable
UTP Cable
RS485 Cable
Alarm Output Cable
Bottom Case
Camera Gimbal
Upper Case
Dome Cover
2
3
4
6
5Cover Screws (x4)
Side Port for Cabling
6
1
3
5
2
4
7
8
9
10
11

6
DIMENSIONS IN MILLIMETERS (IN)*
47.0 1.9
144.0 5.7
61.8 2.4
145.0 5.7
117 0 4 6
125 0 4 9

7
INSIDE THE BOX*
Included with Camera:
1
2
3
4
5
User Manual
Moun ing Template
4 Machine Screws and 4 Dry Wall Anchors
Secondary Video-BNC Cable
L-Key
DC Plug Power Cable
0 9
AB U MA A
B
B
Star ight MPA
Vandal Dome Camera
DWC-V566 T
DWC-V566 T R
6
6

8
SURFACE MOUNT INSTALLATION INSTRUCTIONS*
1. Use the camera or mounting template to mark and drill the
necessary holes in the wall or ceiling.
2. Pull wires through and make connections.
3. Using the four (4) included screws, mount and secure the
camera to the wall or ceiling.
4. Adjust the camera’s Pan and Tilt and Lens.
See pages 15-16 for more information.
5. Use the joystick to adjust the OSD menu. See pages 17-28
for more information.
6. Attach the camera housing to the camera base using the
assembly screws.

9
JUNCTION BOX INSTALLATION INSTRUCTIONS*
Check to see all parts are in
the box.
Use the dry wall anchors and
machine screws to mount the
junc ion box and rubber
gasket to the wall.
Insert wires through he
wall and make the
appropriate connec ions.
Attach he camera to the
junction box using he
machine screws.
Attach the camera housing
to the junction box using the
assembly screws.
1 2 3
4 5

10
WALL MOUNT INSTALLATION INSTRUCTIONS*
Check to see all parts are in
the box.
Insert the wires from he
camera through the wall
mount housing.
Attach the camera to
he wall mount housing.
Use the mounting template to
make pilot holes. Use he dry
wall anchors and machine screws
to attach the assembly to the wall.
Attach he camera housing
to the fixture.
1 2 3
4 5