Digital Watchdog DWC-D1362D User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
High Resolution Indoor Dome
Camera
DWC-D1362D
08092012

2
PRECAUTIONS
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning:
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface:
The material of the mounting surface must be strong enough to support the camera.
FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference. when the equipment is operated in a residential environment. This
equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in
accordance with the instruction manual, it may cause harmful interference to radio communications.
WARNING: Changes or modifications are not expressly approved by the manufacturer.

3
TABLE OF CONTENTS
Introduction
Installation
Troubleshooting
Warranty Information
Memo 18-19
Specifications
Features
Parts and Descriptions
Dimensions
Inside the Box
Installation Instructions
Connecting to Monitors
Adjusting the Camera Lens
4
5
6
7
8-9
10
11
13
14-15
16-17
Adjusting the Camera’s Position 12

4
FEATURES*
1/3” CCD
570 TV Lines (B&W), 540 TV Lines (Color)
3.3~12mm Varifocal Auto Iris Lens
Electronic Day and Night
BLC (Backlight Compensation)
AWB (Auto White Balance)
DRC (Dynamic Range Compressor)
HME (Highlight Masking Exposure)
Programmable Privacy Zones & Motion Detection
Easy Icon Driven OSD Menu with Built-In Joystick
Wide Operating Voltage (8VDC-18VDC)
Secondary Video-BNC Output

5
PARTS & DESCRIPTION*
1Lens
Power Input Connector (12VDC)
Primary Video-BNC Output Connector
Bottom Case
Mounting Screws
Outer Dome Cover
Assembly Screws
2
3
4
5
6
7
1
3
2
4
5
6
7

6
DIMENSIONS IN MILLIMETERS (IN)*
85.0(3.35”)
46.5
(1.83”)
123.8(4.9”) 82.5(3.25”)
88.0(3.46”)
5.0(0.2”)
7.0(0.28”)
46.5
(1.83”)

7
INSIDE THE BOX*
Included with D1 Indoor Dome Camera
User Manual
Mounting Template
2 Machine Screw and 2 Dry Wall Anchors
Miniature TORX Driver
L-Key
Secondary Video-BNC Cable
1
2
3
4
5
6

8
CAMERA INSTALLATION*
Cut a hole in the ceiling for
routing the cables. Use your
mounting template to mark
the screw holes.
Drill holes into the drywall
and insert the drywall
mounts into the holes.
Pull wires through and
make connections.
Mount and secure the
camera to the surface
using the machine screws.
1 2 3
4Position the lens, and
adjust the zoom and focus.
5Assemble the outer dome
cover with the camera
module.
6

9
WALL MOUNT INSTALLATION*
Check to see all parts are
in the box.
Use the mount to mark the
pilot holes are required. Drill
holes into the drywall and
insert the drywall mounts.
Secure the wall mount to the
wall using the mounting
screws.
Attach the base of the camera
to the wall mount with the
smaller machine screws.
1 2 3
4Position the lens, and
adjust the zoom and focus.
5Assemble the outer dome
cover with the camera
module.
6

10
CONNECTING TO MONITORS*
Video Output BNC Cable
Main Monitor
DC12V / AC24V