Digital Watchdog D1362D Series User manual

D1362D Series
About manual
INSTRUCTION MANUAL
Before installing and using the camera, please read this
man al caref ll
5436 W Crenshaw Street
Tampa, FL 33634
www.digital-watchdog.com
Technical Support : 1-866-446-3595 / 813-888-9555
Before installing and using the camera, please read this
manual carefully.
Be sure to keep it handy for future reference.
5436 W Crenshaw Street
Tampa, FL 33634
www.digital-watchdog.com
Technical Support : 1-866-446-3595 / 813-888-9555

PRECAUTIONS
■Do not open or modify
Do not open the case except during maintenance and installation,
as it may be dangerous and cause damages.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get inside the camera. It could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to
strong shock or vibration.
■Install away from electric or magnetic fields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen or boiler
room, as the temperature may rise to high levels.
■Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth
moistened with a soft deter
g
ent solution.
■Do not open or modify
Do not open the case except during maintenance and installation,
as it may be dangerous and cause damages.
■Do not put objects inside the unit
Make sure that no metal objects or flammable substances
get inside the camera. It could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject it to
strong shock or vibration.
■Install away from electric or magnetic fields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen or boiler
room, as the temperature may rise to high levels.
■Cleaning
Dirt can be removed from the case only by wiping it with a soft cloth
moistened with a soft detergent solution.
■Mounting Surface
The mounting surface material must be strong enough to support
the camera.

TROUBLESHOOTING
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your service
center.
■If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Before sending the camera out for repair, check the items below.
If the problem persists after checking these items, contact your service
center.
■If no image appears
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt or fingerprints on the lens can adversely affect the
images. Gently wipe any dirt or fingerprints off the lens
with a soft cloth or lens cleaning paper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENT THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.

DIMENSION (mm)

INSTALLATION
A. Loosen the fixing screw using the L-wrench.
B. Separate the upper case and the base case.
C. Loosen the inner screws using a screwdriver.
D. Detach the gimbal from the base case.
E. Cut a hole in the ceiling for routing the cables.
F. Place the camera horizontally on the ceiling,
drill the screw holes at the marked two positions.
G. Pass the power cable and video cable from the
camera unit through the cable hole in the ceiling.
H. Align the screw holes of the camera unit with
the holes in the ceiling, secure with the two screws.
I. Fix gimbal to the base.
J. Install and ad
j
ust the camera unit.
C
C
D
E
F
G
A. Loosen the fixing screw using the L-wrench.
B. Separate the upper case and the base case.
C. Loosen the inner screws using a screwdriver.
D. Detach the gimbal from the base case.
E. Cut a hole in the ceiling for routing the cables.
F. Place the camera horizontally on the ceiling,
drill the screw holes at the marked two positions.
G. Pass the power cable and video cable from the
camera unit through the cable hole in the ceiling.
H. Align the screw holes of the camera unit with
the holes in the ceiling, secure with the two screws.
I. Fix gimbal to the base.
J. Install and adjust the camera unit.
K. Adjust the dome to show the lens through the
camera window, attach to the base.
L. Put the upper case and the base together.
M. Tighten the screw for the upper/base cases not
to be separated .
A
B
CC
D
E
F
G

CONNECTION
DC12V/AC24V
CAUTION :
Check for polarity when using a 12V DC power supply.
DC12V/AC24V

LENS ADJUSTMENT & GIMBAL ADJUSTMENT
1. Adjust the panning(360˚) and tilt(60˚) position.
2. Setting the zoom position by using Zoom Lever Screw.
3. Setting the focus by using Focus Lever Screw.

D1362D Camera
CAMERA SETTINGS
(1) Adjusting level volume (VR)
If the entire image is too dark or bright, or the backlight compensation is not correct
even after LENS is set to "DC", you need to adjust the level volume.
CCW (Low) Closes the lens iris, making the entire image darker
CW(High) Opens the lens iris, making the entire image drighter
(2) SECOND VIDEO OUT CONNECTOR (2ND VIDEO)
If installer do setting with protable monitor, this connector should be connected.

OSD SWITCH FUNCTIONS
SETUP FUNCTION SUMMARY
LENS MANUAL.DC - DC : bright level
SHUTTER FIXED,MANUAL,FLK - MANUAL : Manual shutter adjust.
- BLCAREA
- BLC RATIO
AGC ON,OFF - AGCGAIN:Min~Max
- MANUAL : RED,BLUE
- FIXED: MODE1,2,3,4
- CONTRAST adjust.
- SHARPNESS adjust.
- CB_GAINadjust.
- CR_GAINadjust.
FUNCTION ☜
- CAMERA ID
- POSITION
MIRROR ON,OFF - Mirror image on/off
- AUTO: DELAY
START LEVEL
DAY NIGHT
AUTO B/W COLOR
ADJUST CONTRAST,SHARPNESS
CB_GAIN,CR_GAIN
CAMERA ID ON,OFF
BLC ON,OFF
WHITEBAL ATW,AWB,FIXED,MANUAL
SETUP FUNCTION SUMMARY
LENS MANUAL.DC - DC : bright level
SHUTTER FIXED,MANUAL,FLK - MANUAL : Manual shutter adjust.
- BLCAREA
- BLC RATIO
AGC ON,OFF - AGCGAIN: Min~Max
- MANUAL : RED,BLUE
- FIXED: MODE1,2,3,4
- CONTRAST adjust.
- SHARPNESS adjust.
- CB_GAINadjust.
- CR_GAINadjust.
FUNCTION ☜
- CAMERA ID
- POSITION
MIRROR ON,OFF - Mirror image on/off
- AUTO: DELAY
STARTLEVEL
ENDLEVEL
- AREA
- MOTION TH
- MOTION TRACE ON/OFF
- AREA SEL
- AREA STATE
GAMMA USER, 0.05~1.0 - GAMMA set.
LANGUAGE ENGLISH,Korean,Chinese1,Chinese
2,日本語 - Language set.
RESET YES,NO - Returns to the level
EXIT - Save out
PRIVACY ON.OFF
DAY NIGHT AUTO,B/W,COLOR
MOTION ON,OFF
ADJUST CONTRAST,SHARPNESS
CB_GAIN,CR_GAIN
CAMERA ID ON,OFF
BLC ON,OFF
WHITEBAL ATW,AWB,FIXED,MANUAL

WARRANTY INFORMATION
Digital Watchdog (referred to as “the Warrantor”) warrants the Camera
Series against defects in materials or workmanship as follows:
LABOR: For the initial five (5) years from the date of original purchase, if the
camera is determined to be defective, the Warrantor will repair or replace the
unit, with
new or refurbished product at its option, at no charge.
PARTS: In addition, the Warrantor will supply replacement parts for the initial
five (5) years.
To obtain warranty or out of warranty service, please contact a Technical
Support Representative at 1-866-446-3595 Monday through Friday from 9:00
AM to 5:00 PM Eastern.
A purchase receipt or other proof of the date of the original purchase is
required before warranty service is rendered. This warranty only covers
failures due to defects in materials and workmanshi
p
which arise durin
g
Digital Watchdog (referred to as “the Warrantor”) warrants the Camera
Series against defects in materials or workmanship as follows:
LABOR: For the initial five (5) years from the date of original purchase, if the
camera is determined to be defective, the Warrantor will repair or replace the
unit, with
new or refurbished product at its option, at no charge.
PARTS: In addition, the Warrantor will supply replacement parts for the initial
five (5) years.
To obtain warranty or out of warranty service, please contact a Technical
Support Representative at 1-866-446-3595 Monday through Friday from 9:00
AM to 5:00 PM Eastern.
A purchase receipt or other proof of the date of the original purchase is
required before warranty service is rendered. This warranty only covers
failures due to defects in materials and workmanship which arise during
normal use. This warranty does not cover damage which occurs in shipment
or failures which are caused by products not supplied by the Warrantor or
failures which result from accident, misuse, abuse, neglect, mishandling,
misapplication, alteration, modification, faulty installation, set-up adjustments,
improper antenna, inadequate signal pickup, maladjustment of consumer
controls, improper operation, power line surge, improper voltage supply,
lightning damage, rental use of the product or service by anyone other than
an authorized repair facility or damage that is attributable to acts of God.