Digital Watchdog MC352-29 User manual

INSTRUCTION MANUAL
Beforeinstalling and using the camera, please readthis manual
carefully.Be sure to keep it handy for later reference.
■Do not open or modify
Do not open the cabinet exit during maintenance and
installation, as it may be dangerous and cause damages.
■Do not put objectsinside the unit
Make sure that no metal objects or flammable substances get inside
the camera. It could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■Install away from electric or magneticfields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen or boiler
room, as the temperaturemay raise to high levels.
■Cleaning
Dirt can be removed from the cabinetonly by wiping it
with a soft cloth moistened with a soft detergentsolution.
■Mounting Surface
The mounting surface material must be strong enough to secure the
camera.
INSTALLATION
WARRANTY INFORMATION
Digital Watchdog
(referred to as
“
the Warrantor
”
) warrants the
This warranty gives you specific legal rights and you may also have
other rights that vary from state to state.
If the problemis not handledto your satisfaction,then write to the
PRECAUTIONS
MC352 /MC352-29
About this manual
5436 W Crenshaw Street
Tampa, FL 33634
www.digital-watchdog.com
Technical Support : 1-866-446-3595 / 813-888-9555
Beforeinstalling and using the camera, please readthis manual
carefully.Be sure to keep it handy for later reference.
TROUBLESHOOTING
Beforesending the camera out for repair,check the items below. If the
problem persists after checking these items, contact your service
center.
■If no image appears.
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt of fingerprints on the lens can adverselyaffect the
images. Gently wipe any dirt or fingerprintsoff the lens
with a soft cloth or lenscleaningpaper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENTTHE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
■Do not open or modify
Do not open the cabinet exit during maintenance and
installation, as it may be dangerous and cause damages.
■Do not put objectsinside the unit
Make sure that no metal objects or flammable substances get inside
the camera. It could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■Install away from electric or magneticfields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen or boiler
room, as the temperaturemay raise to high levels.
■Cleaning
Dirt can be removed from the cabinetonly by wiping it
with a soft cloth moistened with a soft detergentsolution.
■Mounting Surface
The mounting surface material must be strong enough to secure the
camera.
INSTALLATION
WARRANTY INFORMATION
Digital Watchdog (referred to as “the Warrantor”) warrants the
CameraSeries againstdefectsin materials or workmanship as follows:
LABOR: For the initial five (5) years from the dateof originalpurchase,
if the camera is determined to be defective,theWarrantor will repair or
replace the unit, with
new or refurbished product at its option, at no charge.
PARTS: In addition, the Warrantorwill supply replacement parts for the
initial five(5) years. To obtainwarranty or out of warranty service,
please contact a Technical Support Representative at 1-866-446-3595
Monday through Friday from 9:00 AM to 5:00 PM Eastern.
A purchase receipt or other proof of the date of the original purchase is
requiredbefore warranty service is rendered. This warranty only
coversfailures due to defectsin materials and workmanship which
arise during normal use. This warranty does not cover damage which
occurs in shipment or failures which are caused by products not
suppliedby the Warrantor or failures which result from accident,
misuse, abuse, neglect, mishandling, misapplication, alteration,
modification,faulty installation, set-up adjustments, improper antenna,
inadequatesignal pickup, maladjustmentof consumer controls,
improperoperation, power line surge, improper voltage supply,
lightningdamage, rental use of the productor service by anyone other
than an authorized repair facility or damage that is attributable to acts
of God.
This warranty gives you specific legal rights and you may also have
other rights that vary from state to state.
If the problemis not handledto your satisfaction,then write to the
Address above.
Servicecalls which do not involve defectivematerials or workmanship
as determined by the Warrantor, in its sole discretion, are not covered.
Costs of such service calls are the responsibility of the purchaser.
LIMITS AND EXCLUSIONS
There are no express warranties exceptas listed above.The Warrantor
will not be liable for incidental or consequentialdamages (including,
without limitation, damage to recording media) resulting fromthe use of
these products, or arising out of any breach of the warranty. All express
and implied warranties, including the warranties of merchantability and
fitness forparticular purpose, are limited to the applicable warranty
period set forth above.
Some states donot allow the exclusion or limitation of incidental or
consequentialdamages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
PRECAUTIONS
MC352 /MC352-29
About this manual
5436 W Crenshaw Street
Tampa, FL 33634
www.digital-watchdog.com
Technical Support : 1-866-446-3595 / 813-888-9555
A. Removing the screw on the upper case by using
L-wrench.
B. Separate the upper case from the bottom case
C. Make the 4 mounting screw hole on the ceiling/wall by drawing the
positions using the bottom case
D. PutPowercable andVideocable intotheceiling/wall.
E. Align the bottom case to the ceiling/wall by using
the screws.
F. Adjust the camera to its position
(Referance - "CAMERA SETTING" )
G. Connect the upper case and bottom case.
H. Tighten the Stop Screw to the upper case using L-wrench.
E
D
C
B
A
F
Beforeinstalling and using the camera, please readthis manual
carefully.Be sure to keep it handy for later reference.
TROUBLESHOOTING
Beforesending the camera out for repair,check the items below. If the
problem persists after checking these items, contact your service
center.
■If no image appears.
Is the coaxial cable attached securely?
Are the power and voltage normal?
Has the iris of the lens inside the camera been
adjusted correctly (with the level volume) ?
Is there adequate illumination?
■If the image is unclear
Is the lens in focus?
Is the lens dirty?
Dirt of fingerprints on the lens can adverselyaffect the
images. Gently wipe any dirt or fingerprintsoff the lens
with a soft cloth or lenscleaningpaper and cleaning
fluid (commercially available).
Is the monitor adjusted correctly?
WARNING:
TO PREVENTTHE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO
RAIN OR MOISTURE.
■Do not open or modify
Do not open the cabinet exit during maintenance and
installation, as it may be dangerous and cause damages.
■Do not put objectsinside the unit
Make sure that no metal objects or flammable substances get inside
the camera. It could cause fire, short-circuits or damages.
■Be careful when handling the unit
To prevent damage, do not drop the camera or subject
it to strong shock or vibration.
■Install away from electric or magneticfields
■Protect from humidity and dust
■Protect from high temperature
Be careful when installing close to the ceiling , in a kitchen or boiler
room, as the temperaturemay raise to high levels.
■Cleaning
Dirt can be removed from the cabinetonly by wiping it
with a soft cloth moistened with a soft detergentsolution.
■Mounting Surface
The mounting surface material must be strong enough to secure the
camera.
INSTALLATION
WARRANTY INFORMATION
Digital Watchdog (referred to as “the Warrantor”) warrants the
CameraSeries againstdefectsin materials or workmanship as follows:
LABOR: For the initial five (5) years from the dateof originalpurchase,
if the camera is determined to be defective,theWarrantor will repair or
replace the unit, with
new or refurbished product at its option, at no charge.
PARTS: In addition, the Warrantorwill supply replacement parts for the
initial five(5) years. To obtain warranty or out of warranty service,
please contact a Technical Support Representative at 1-866-446-3595
Monday through Friday from 9:00 AM to 5:00 PM Eastern.
A purchase receipt or other proof of the date of the original purchase is
requiredbefore warranty service is rendered. This warranty only
coversfailures due to defectsin materials and workmanship which
arise during normal use. This warranty does not cover damage which
occurs in shipment or failures which are caused by products not
suppliedby the Warrantor or failures which result from accident,
misuse, abuse, neglect, mishandling, misapplication, alteration,
modification,faulty installation, set-up adjustments, improper antenna,
inadequatesignal pickup, maladjustmentof consumer controls,
improperoperation, power line surge, improper voltage supply,
lightningdamage, rental use of the productor service by anyone other
than an authorized repair facility or damage that is attributable to acts
of God.
This warranty gives you specific legal rights and you may also have
other rights that vary from state to state.
If the problemis not handledto your satisfaction,then write to the
Address above.
Servicecalls which do not involve defectivematerials or workmanship
as determined by the Warrantor, in its sole discretion, are not covered.
Costs of such service calls are the responsibility of the purchaser.
LIMITS AND EXCLUSIONS
There are no express warranties exceptas listed above.The Warrantor
will not be liable for incidental or consequentialdamages (including,
without limitation, damage to recording media) resulting fromthe use of
these products, or arising out of any breach of the warranty. All express
and implied warranties, including the warranties of merchantability and
fitness forparticular purpose, are limited to the applicable warranty
period set forth above.
Some states donot allow the exclusion or limitation of incidental or
consequentialdamages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
PRECAUTIONS
MC352 /MC352-29
About this manual
5436 W Crenshaw Street
Tampa, FL 33634
www.digital-watchdog.com
Technical Support : 1-866-446-3595 / 813-888-9555
A. Removing the screw on the upper case by using
L-wrench.
B. Separate the upper case from the bottom case
C. Make the 4 mounting screw hole on the ceiling/wall by drawing the
positions using the bottom case
D. PutPowercable andVideocable intotheceiling/wall.
E. Align the bottom case to the ceiling/wall by using
the screws.
F. Adjust the camera to its position
(Referance - "CAMERA SETTING" )
G. Connect the upper case and bottom case.
H. Tighten the Stop Screw to the upper case using L-wrench.
E
D
C
B
A
F

■CONNECTIONS ■LENS ADJUSTMENTS
■CAMERA SETTINGS
(Uppe Case & Bottom Case )
CONNECTIONS AND CAMERA SETTINGS
CAUTION
Check for polarity when using a DC 12V power supply. Adjust the panning(360˚) and tilt(41˚) position.
DIMENSIONS
A
CONNECTIONS AND CAMERA SETTINGS
CAUTION
Check for polarity when using a DC 12V power supply. Adjust the panning(360˚) and tilt(41˚) position.
Camera Position Adjustment :
(1)Loosen the Screw(B) on the upper case by using L-Wrench(A).
(2)Separate BOTTOM CASE(E) from UPPER CASE(C) by turning UPPER CASE(C) to the
right.
(3)Separate CLEAR DOME(D) from BOTTOM CASE(E).
(4)Fixing the camera position in BOTTOM CASE(E).
(5)Assemble CLEAR DOME(D) and UPPER CASE(C) with BOTTOM CASE(E)
(6)Tightening Screw(B) on the Upper case(C) by using L-Wrench(A).
DIMENSIONS
A
B
C
D
E

Model
Camera TYPE Color Anti-Vandal Digital Micro Dome Camera
Mount M9
Image Device 1/3" Super HAD II CCD
Pixels-Total 811(H) x 508(V)
Pixels-Effective 768(H) x 494(V)
Scanning System NTSC
Horizontal Frequency Internal Mode 15,734Hz
Vertical Frequency Internal Mode 59.94Hz
Min. Scene Illumination F1.2 (30IRE, MC352), IR LED
(MC352DIR)
0.4 Lux
IR DISTANCE IR ( MC352DIR only) 23 feet range
DIP Switch W/O
Lens Fixed Length 3.6mm
2.9mm(MC352-29)
Resolution Horizontal 540 TV Lines
Video Output VBS 1.0Vp-p 1.0Vp-p (75 load)
S/N Ratio S/N Ratio 48dB
Environmental Operating Temperature -10℃~ +50℃
Humidity Less than 90%
Power Power Requirement 12VDC
Power Consumption 12VDC: 77mA
Physical Specification Dimensions(φx H) 80.0 x 28.0mm
Nema Type IP66
Weight 0.4lbs
Certifications CE, FCC, RoHS Certified
Specifications MC352 / MC352-29 ( Day & Night)