Digital Zone T7 HVP-7004N Setup guide

2 sets of T7 (Multi UHD Player)
How to set Sync Play Mode
DigitalZone co., Ltd.

Components Description

2 sets of Multi UHD Player (HVP-7004N) Network Cable (Cross Cable)
Remote IR Extension receiver User Manual
Adaptor & Power cord HDMI cable(Option)
What kind of materials do you need for installation?
3

Package
4
Package Weight: 5.3 KG
430mm
270mm
290mm
Adapter, Accessories
and HDMI Cables
T7T7 User
Manual
Adapter, Accessories
and HDMI Cables

How to Use T7 as a Multi UHD Player

How to update firmware
6
1. Connect USB in the Front.
2. Save the firmware file in the root folder and do
not copy more than 2 firmware files.
Connect USB
1
2
1. Press Set-up in RCU and you can see Settings menu.
2. Press Left or Right button to move to ‘UPDATE’ page.
3. When new firmware is detected, new version will be shown.
* If new firmware is not detected, re-connect USB stick
to other USB port at rear of unit.
4. Select ‘OK’ and press Enter to proceed update.
** Do not turn off the unit during update.

How to update new contents
Connect USB
1
2
1. Connect USB in the Front.
2. USB media menu will only appear when USB
storage is connected.
1. Press UPDATE on remote control to open Update menu.
2. Use Left/Right button “◀ ▶” to move from USB media source.
3. Use ‘CHECK’ button of remote to select files which will be copied
to the selected play list into the built-in HDD.
4. Press ENTER to start update the selected files.
CHECK
UPDATE
Select Play List Select USB
Select Files and press “Enter”
7

How to make Contents for Sync Play

Video format (CODEC, Container)
1. CODEC
•VIDEO : HEVC, H.264
•AUDIO : AAC, AC3
•MPEG TS(Transport stream)
2. Container
•Necessary for the same Play List
- The file order in the same Play List should be the same.
3. Limitation
•Necessary for the same format in the list (Because of seamless)
- Every information in the contents should be the same. ( PID, Codec Info, Bit-rate Info, Refresh-rate Info)
9
Master Slave 1 Slave 2

The policy & rules for making HEVC file
Classification Setting
Maximum Profile & Level Main10_High[email protected] (8 or 10bit)
Maximum Resolution
and Refresh rate ~3840x2160, ~60Hz(4:2:0),
Bit-rate mode CBR
Maximum Bit-rate ~80Mbps
QP value
(Quantization Parameter 0~51) QP minimum: over 13
Container MPEG TS
Audio
MPEG 1 layer I, II & III
MPEG 4 AAC-LC Stereo & 5.1
DTS & DTS-HD
Dolby Digital Stereo & AC3 5.1/7.1
Audio & Video Fade-in 0.5 second
Audio & Video Fade-out 0.2 second
Running time Same
** Note : Video PID and Audio Codec has to be same if you want to playback files in Sync.
10
HEVC (H.265) Format
1. Start Time : Fade-in for 0.5 second (Video, Audio)
2. Ending Time : Fade-out for 0.2 seconds (Video, Audio)

The policy & rules for making H.264 file
11
Classification Setting
Maximum Profile & Level
[email protected] (8 bit)
Maximum Resolution and Refresh rate
~3840x2160, ~29.97Hz
Bit-rate mode
CBR
Maximum Bit-rate
~40Mbps
Container
MPEG
TS
Audio
MPEG 1 layer I, II & III
MPEG 4 AAC
-LC Stereo & 5.1
DTS & DTS
-HD
Dolby Digital Stereo & AC3 5.1/7.1

How to Set T7 as a Multi UHD Player

How to set the players
13
Settings
1. Firmware : firmware version must be 1.20 or above to set synchronize mode
2. Interface Menu:
–Configure : Manual
–Set IP : Master : 101 / Slave : 102
3. TimeZone : Necessary of modification/Reservation has to be ON
4. Select Master or Slave and Seamless Off in admin menu
Master Slave

Hardware Installation

How to connect network cable with switching hub
15
1. Network Cable
A. Connect Network cables between T7 and Switching Hub. If you are using only 2 sets of T7, then you need
Cross Cable without a switching hub.
Master : T7 HVP-7004N
Slave: T7 HVP-7004N
Cross Cable

How to HDMI cables
16
2. HDMI Cable
You have to check TV Layout and T7
HDMI cables have to be connected to right TV from right T7.
It will be convenient for monitoring if the Master set is connected separately.
It will be better to use name tag each end of cables for distinguish the cables.
Master
Slave
Separated TV for
monitoring T7 Side TV Side
Master
Slave 1

How to connect power code
17
3. Adaptors & Power Code
A. Connect Power code into Adaptor
B. Connect Powers into T7
C. Power code has to be connected in one place for easy turn on / off at once.
D. So prepare power board with multi outlet. For example, 1 set of 4 outlet power board for 2 x T7 & 1
Switching Hub.

Check Points after Hardware Installation

What kind of things do I have to check after installation
19
1. Network Cable Connection
A. Check LED lights in the front of T7. LEDs for Power, Network, Play have to be ON.
B. Also check LEDs for resolution if it is UHD resolution or FHD resolution with refresh rate.

2. HDMI Cable connection
A. If you cannot see the display in TV, please check HDMI cable first if it is connected firmly in TV side and T7 side.
B. If you cannot see any display, change the HDMI cable.
What kind of things do I have to check after installation
20
You can use one of
4 HDMI outputs.
TV