DIGITALas A260 TTLOCK User manual

A260 TTLOCK VERSION
Version 1.0 Edition 2020
Smart your life!
User Manual-Smart Digital Lock
Fingerprint
Password
Search Google Play or APPLE Store with TTLOCK

PACKING ACCESSORIES
4
3
Keypad
Induction Area
Cylinder
Battery Box
Speaker
Back Handle Reset Button
Micro-USB
Aluminum Alloy,ABS,Arcylic
Fingerprint,IC Card,password,APP,wristban,mechanical key
Support 60#Single latch, 6050/5572/4585/6085/7085 mortise
Available
Factory Password
Card:200 group/password:150 groups/Fingerprint: 100 groups, one admin
Factory master password:123456,after configuration,it will be invalid
10%~95%
-20~50 degree
1~1.5 seconds
<200mA
≦50uA
DC6V:4pcs AA alkaline batteries
Black/Satin Nickle
7000 times normal unlock(10-12 months)
35-55mm
Bluetooth
iOS 7.0 or above, Android 4.4 or above
1
Privacy Button
Mortise
Back Panel
Front Panel Strike Plate
1 Pcs 1 Pcs 1 Pcs 1 Pcs 1 Pcs
Strike Box
M5x60
1 Pcs 1 Pcs
ST4x20
4 Pcs
Cylinder
1 Pcs
Mechanical Key
2 Pcs
M5x40
1 Pcs
fghijk
70L Spindle
Please check the packing box and accessories when you got the lock in hand.
2
There is one privacy button on the back panel.
You can pull upward this button with sound tip“Locked”,
then the lock is dead locked inside, only the administrator
can access the door, other user password or card will be invalid.
And you can pull downward the button one more time with sound
tip“Unlocked”to cancel this function.
Privacy Button
DEAD LOCK FUNCTION
There is one Reset button on the back of rear panel.
You can press this button for 5 seconds with two sound tip,
then the lock is under factory state, the default master password is: 123456
you can open the door with any password or fingerprint.
PRODUCT SPECIFICATION RESET TO FACTORY STATE
TO OPEN AND CLOSE &BELL FUNCTION
Enter the valid password or touch the IC card or press the finger to open the door.
Bell function: You can press the button“#”to ring the bell.
Factory State:
Master passcode is 123456.
Back Panel
Virtual Password
User Capacity
Fingerprint Sensor
Door Bell
SYSTEM INTRODUCTION
2
1

5INFORMATION AND SAFETY WARNINGS:
This user manual will guide you through the functions and usages of our A260 Wi-Fi smart lock. It is
important that you follow the instructions and regard all notes that appear throughout this manual.
Consult this manual before you attempt to use this lock. If you have any questions that not answered by
this manual or on need of non-routine service, please call our customer service hotline or send FAQ to us.
5.2 Safety Warnings:
5.1 Introduction
Drill Hole with Template
6PREPARING TO INSTALL
6.1 Line Drawing
When reading this manual, note these icons: notes with the icon Must be read, understood and
obeyed to prevent injury or damage to the lock.
General Usage
This lock shall only be used as described in this manual.
Verify that all parts of the lock are accounted for. If any parts are missing, please contact our
service person.
Under factory default state,the lock is on always open status after you install the lock(no power on).
It means the handle is free and lock can’t be locked, you shall power on the lock with batteries or
set admin and pair the lock with the APP and then the lock will be under private mode automatically.
Handle directions are reversible, please kindly follow chapter 6 to change the direction if the door
opening direction is not same with your lock. Should you have any problem, please contact our
service person.
There is protective film on the front touch panel, if there are some scratches on the film, please
remove the film if you need.
Please use 4pcs AA batteries. Do not mix old and new batteries or other Zn/Mn batteries.
Never insert objects into the lock other than batteries as described in this manual.
Verify all surfaces are flat and level before beginning installation, installation on doors or surface
with any types of deformity such as gaps or warping may cause the lock to malfunction or fail to
operate entirely.
Never apply any cleaner directly to any part of this lock. Only use clean water or mild cleaner on
a soft non-abrasive cloth when cleaning.
Potential shock warning: do not allow water or liquids to get into the lock’s electric parts.
The lock must be used with TTLOCK APP. The lock will function without the APP but full functionality
may only be achieved when the APP is on use.
5.3 SALES AND SERVICE TERMS
Any change submit to our confirmation
Any error or question in our manual or sales term, please feel free to contact with us.
It is forbidden to copy our manual and for other usage, except the authorized company and users.
For any wrong operation or installation to the user or third party, we do not responsible for the duty.
For the damage caused by anthropic factor or inevitable reason, we do not pay for the loss or maintain
for free, please check our after sale service terms.
Please do not take apart the lock if you are not technician, if necessary, please make the operations
under the guide of technician.
Notice: there maybe a little difference for product pictures with real product, please subject to our
real products.After changing the battery, please do not throw away the battery, kindly refund to recycle
bin in case of pollution!
Limited 1-Year Electronic Warranty Limited Lifetime Mechanical and Finish Warranty
This A260 product comes with a 1-Year Limited Warranty on Electronic Parts and a Limited Lifetime
Mechanical and Finish Warranty against defects in materials and workmanship under normal use to
the original residential user. Proof of purchase and ownership is required for the warranty to be in effect.
Please read the manual carefully before use!
34
6.2 Adjust Direction
6.2.1.Adjust from Right Direction(For Sample)to Left
Drawing Center Line
Drill hole for StrikeTest with Mortise
Step 1 Step 2 Step 3
Draw a horizontal center line inside and outside the door at 1 meter from the ground. Fold the hole
template,make the handle center line align at the door horizontal center line, then draw out the hole
lines at front and side.
1. Use the allen key to take off the screw on the right position.
2. Turn the handle to 180 degree counterclockwise.
3. Tighten the screw in left position.
6.2.2.Adjust from Right Direction(Back Panel)to Left
1. Use the allen key to take off the screw on the right position.
2. Turn the handle to 180 degree counterclockwise.
3. Tighten the screw in left position.
1
2
3
18 0°
2
180°
13

7
7.1 Assemble the Mortise
Assemble the mortise( ) into the slot which
is drilled according to the template(45/85 Mortise).
c
7.2 Assemble the Front Panel
Fix the front panel(a) on the door and cross the cable
through the hole.
7.3 Connect the Cable
Insert the 70L spindle on mortise, cross the cable
through the hole and connect with the PCB board.
7.4 Fix the Lock Panel
Tight the back panel with front panel with the
two long screws.
a
7.5 Assemble the Battery Box
Put 4pcs AA alkaline batteries and fix the
battery box cover.
7.8 Adjust the Lock Panel
After finishing installation, please adjust the
position of the lock panel or the screws whether
it is too tight.Test with password: 123456 and
turn the manual key and then press the handle
to open.
56
b
INSTALL THE LOCK
2
1
3
h
f
g
OPERATION STEPS
3sec
Press *39 #123456#2#
Change to English voice tip
Press the reset button and hold 3 seconds Please input initialization passcode,
enter: 000#, with sound : “Successful”
Please enroll the administrator before you start to use this lock. you can follow the operation
steps as below:
1.Initialization
2.Change Language
000#
2.Enroll Mobile Administrator
Factory state: Default master passcode is:123456.
or
Press *39 #123456#1#
Change to Chinese voice tip
Touch screen, light on
Voice tip:”please add Bluetooth administrator”.
2.1 Factory state: press *12#123456#new passcode#new passcode#.
2.2 You can use the mobile APP to add the Bluetooth administrator.
When adding the door locks, operations must be completed near the lock.
Step 1: Click “+” button Step 2: Select the lock Step 3: Click the device name
A260BLE_0163bd

8
7
Please input Administrator passcode
For sample: 123123
Input new Master passcode
Such as:654321
Please enter fingerprint or passcode
Press your finger
4
please input again
5
Operation successful!
You can test the new passcode
Enter same password
Press * 80 # button by sequence Please enter passcode,confirm
with # key. such as:654321
5
3.Change Master Passcode
4.Enroll User Fingerprint
6.Enroll User Password
Please Input Administrator passcode
Please Input Administrator passcode
Press *12 #
you can find the new master passcode in the mobile APP under “Settings”.
also you can edit the master passcode on App directly and upload Admin passcode to the lock like the below photo.
you can also change the master passcode on the lock directly.
Please find the operation steps below:
Press *80 # button
4
please press again
5
Input successful!
You can continue to add the new fingerprint
4 times
Please enter again
Enter same passcode
confirm with # key
Input successful!
You can continue to add the new passcode
Under the mobile APP, you can upload the added passcodes to the lock and server.
Operation successful!
All fingerprints are deleted.
5.Delete User Fingerprint
Please Input Administrator passcode
Press *70 # button
APP operation: you can deleted the added fingerprints one the lock and server.

910
7.Delete User Passcode
Press *71 # button by sequence Please Input Administrator passcode Operation successful!
all passcodes are deleted.
Under the mobile APP, you can find the added passcodes, you can edit any passcode and click Delete button to delete the passcode.
Touch one IC card to
the induction area
4
Input successful!
please input fingerprint or passcode
You can continue to add user card
IC Card
8.Enroll User Card
Press * 80 # button by sequence Please Input Administrator passcode Please enter fingerprint or passcode
IC Card
Under the mobile APP, you can upload the added cards to the lock and server.
9.Delete User Card
Press *69 # button by sequence Please Input Administrator passcode Operation successful!
all user cards are deleted.
Under the mobile APP, you can find the added IC Cards, you can edit any username and click Delete button
to delete the card, also you can choose upload IC Cards to ensure the card is deleted in the server.
10.Passage Mode
Unlock the door with any valid passcode or fingerprint.
Press 123# button during the time of unlocking.
Sound tip: the lock set to passage mode
Then the lock is under always open state, you can enter any valid
passcode or fingerprint to cancel this function.
Press 123#
any valid passcode
or fingerprint
11.Unlock Records
You can find the unlock records for the passcode/IC Card/Fingerprint etc.
More details, you can refer the manual of our TTLOCK App operation steps.