Digitus DK-1P32-050 User manual

E-Mobility – Charging cable
type 2 to type 2
Quick Instalation Guide
DK-1P32-050/ DK-1P32-075/ DK-1P32-100/
DK-1P32-S-050/ DK-1P32-S-075/ DK-1P32-S-100/
DK-3P16-050/ DK-3P16-075/ DK-3P16-100/
DK-3P16-S-050/ DK-3P16-S-075/ DK-3P16-S-100/
DK-3P32-050/ DK-3P32-075/ DK-3P32-100/
DK-3P32-S-050/ DK-3P32-S-075/ DK-3P32-S-100 – Rev. 1.0

2
Please read this manual carefully before installation and use,
otherwise, it may interfere with the normal use of the equipment
and even risk causing personal injury.
1. Safety and Points for Attention
1.1. Installation & Maintenance
Before installation, please visually inspect the
appearance to check whether the equipment is
damaged during transportation. If it is damaged, please
immediately notify the carrier or the manufacturer.
Do not drop any foreign objects, especially metal
objects, into the charging plug or connector pins.
Do not step on the cable and do not violently pull out
the charging connector
Please do not use the charging cable outside its normal
operating range of -30 to +50°C.
The Charging cable has an IP rating of IP55 for dust
and waterproof. Please use it with care under this
IP55 rating.
IP55 is ensured only when the products are engaged
with vehicle inlets with protection degree higher or
equal to IP55.
When the products are fully engaged with the vehicle
inlets with protection degree lower than IP55, the lower
protection degree of the two accessories shall be
checked.

3
Please do not dismantle the protective cap. To protect
the charging connector from moisture and dirt, after
every use, put the protective caps back on.
Please do not withdraw the connector and plug out of
EV inlet and socket while under load.
Additional adaptors and conversion adapters are not
allowed to be used with this cable.
Cord extension sets are not allowed to be used with this
cable assembly.
The max cable length shall not exceed 5m when used in
Switzerland.
Please make sure that the charging adapters and the
cable are free from any signs of scratches, rust, cracks
before usage.
Before charging, please make sure the power plug and
outlet are compatible as IEC 62196-2.
DO not insert any fingers into the charging plug.
Use the product under normal away from high
temperature erosive materials or ignition source.
Please make sure that the plug & connector are fully
inserted until it clicks into place.
It is recommended that routine safety inspection on the
cable.

4
Please do not attempt to disassemble, repair, or modify
the charging cable by yourself. If there is a need for
maintenance or modification, please contact the
manufacturer. Improper operation may cause damage
to the equipment.
Do not put inflammable, explosive or combustible
materials, chemicals, combustible steam and other
dangerous goods near the charging cable, otherwise
there is a risk of fire.
Please keep the charging adapter clean and dry and
wipe with a clean, dry cloth if soiled. Do not touch the
charging plug or connector with your hand when
charged.
If the unit does not work properly in accordance with
the operating instructions, please do not use this unit.
1.2. Operations
Strictly forbidden for Children or persons of restricted
capacity to approach the charging cable to avoid injury.
Forced charging is strictly forbidden when the electric
vehicle or charging station fails.
Electric vehicle can only be charged with the engine is
off and stationary.
It is strictly prohibited to use the charging cable when
the charging adapter or charging cables are defective,
cracked, worn, broken or the charging cables is
exposed. If you find any, please contact the supplier in
time.

5
In case of rain or thunder, please charge with care.
The charging cable is only for EV charging application.
Please do not submerge the charging cable in water.
2. Features
•Charging plug and connector meet IEC 62196-2
standard.
•Robust and durable TPU jacket
•Charging adapter is with IP55 waterproof rating for
outdoor usage.
•Long durability: Charging adapter at no-load plug in/pull
out > 10000 times
•High impact of external force resistance
3. Package content
•EV Charging Cable (1 piece)
•Quick Installation Guide (1 piece)

6
4. Technische Specification
Cable
Type
TPU jacket
Length
Available with 3m,
5m, 7.5m, 10m
Cable
5G2.5mm² (16A) /
5G6mm² (32A)
Color
Black
Design Standard
Plug
EN 62196-2 (Type 2)
Electric spec
Rated voltage
240/415Vac
Rated power
7.4kW/11kW / 22kW
Rated current
16A / 32A
No. of phase
1/3-Phase
Contact resistance
0.5mΩ (Max)
Insulation
resistance
1000MΩ (Min) @
DC500V
Withstand voltage
2000V
Environmental
spec
Working
temperature
-30°C ~ +50°C
Working humidity
5% -95% non-
condensed
Flammability
standard
UL94 V-0
IP Protection
IP55
Mechanical
spec
Insertion life cycles
> 10000 times

7
5. Installation
Please note that the Charging cable has 2x ends of plugs.
The male plug is used towards the Charging Station side
while the female plug is connected towards the Electric
Vehicle side.
Male plug Female plug

8
Model
Number
Jacket Description Rating Cable Spec
DK-1P32-XXX TPU
Type2 to
Type2
EV Charging
Cable
(Straight)
1-Phase/
240V/32A/
7,4kW
3×6mm2 +
1x0.75mm2
DK-3P16-XXX TPU
Type2 to
Type2
EV Charging
Cable
(Straight)
3-Phase/
415V/16A/
11kW
5×2.5mm2
+
1x0.75mm2
DK-3P32-XXX TPU
Type2 to
Type2
EV Charging
Cable
(Straight)
3-
Phase/415
V/32A/22k
W
5×6mm2 +
1x0.75mm2
DK-1P32-S-XXX TPU
Type2 to
Type2
EV Charging
Cable
(Spiral)
1-Phase/
240V/32A/
7.4kW
3×6mm2 +
2x0.5mm2

9
Hereby Assmann Electronic GmbH, declares that the
Declaration of Conformity is part of the shipping content. If
the Declaration of Conformity is missing, you can request it
by post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
,
58513 Lüdenscheid
Germany
DK-3P16-S-XXX TPU
Type2 to
Type2
EV Charging
Cable
(Spiral)
3-Phase/
415V/16A/
11kW
5×2.5mm2
+
2x0.5mm2
DK-3P32-S-XXX TPU
Type2 to
Type2
EV Charging
Cable
(Spiral)
3-Phase/
415V/32A/
22kW
5×6mm2 +
2x0.5mm2