Digitus DS-53200 User manual

VGA over IP EXTENDER
Manual
DS-53200

2
1. Introduction
Thanks for purchasing the DS-53200 VGA over IP Extender. We recommend that you read
this manual thoroughly and retain for future reference.
1.1 Features
The VGA over IP Extender allows you to extend video and audio up to 100 meters distance
between source or computer and monitor or projector. With the built-in video and audio
signals enhancement, you can gain the best video resolution quality and audio stereo sound
while listening, and no any additional software needed. Furthermore, the installation and
operation are easily more than expected. With using extension facilities of video and audio,
this product the VGA over IP Extender,delivers worthy of performing efficiency and
value-added.
Cascadable Receiver, each Receiver Unit with cascade function enables to link the
other two Receiver Units consecutively extending another 100m distance, and continue
expanding corresponding to custom demand as likely Cascade/Tree Chain web
architecture spread
Easy to install with inexpensive CAT.5e/6 cables
Each pair (TX & RX) extends the signals up to 100m (330 feet)
Supports video high resolution up to 1920x1080@60Hz, Full HD 1080p
HDTV compatible (720p, 1080i, 1080p)
Supports Stereo 2.0
Cascaded-chainable receiver up to 10 layers
Supports RS-232 (Serial)
IR (Infrared remote) enabled
Support Local VGA monitoring port
Each receiver (remote) distributed linking cascade-chainable 2 receivers
Wall Mountable
1.2 Package Contents
1. VGA Extender Transmitter (TX) x 1
2. VGA Extender Receiver (RX) x 1
3. Audio cable x 1
4. RS232 adapter cable x 2 pcs (set units) or 1 ( single unit)
5. IR ( Emitter + Receiver ) cables x 1 set
6. Power Adaptor DC 5V x 2 pcs ( set units ) or 1 ( single unit )
7. User’s Manual x 1

3
2. Specifications:
2.1 General
Transmitter Receiver
Console
Connectors
VGA Output VGA (Female) VGA (Female)
RS-232 Control
Port Phone Jack Phone Jack
PC
Connectors VGA Input VGA (Male) N/A
Extension
Port RJ-45 Full HD Video / Audio Extension
RJ-45 1 (Line Out) 3 (1 Line In & 2 Line Out)
Cascaded-Chainable N/A Up to 10 layers
Audio Supports Stereo 2.0
IR Unidirectional (Receiver RX to Transmitter TX)
LED
Indicators
Local
Power Red LED
Link Red Green
Remote
Power Red LED
Link Red Green
DDC Supported DDC/ DDC2 /DDC2B
Extension Cable Type &
Length CAT.5e / CAT.6 Max. Length: 100m
Max. Video Resolution HDMI: 1920 x 1080@60Hz, Full HD 1080p
Wide Screen Supported yes
Power Supply External DC 5V / 2A Power Adapter
Dimension ( L x W x H ) 115 x 91 x 28 mm
Weight 340g 380g
Housing material Metal
Power Consumption Transmitter (TX) : 5W ; Receiver (RX): 4.5W
Operating Temperature 32 – 122 F ( 0 – 50 C )
Working Temperature -20 ℃~ 60 ℃
Humidity 0% - 80% RH

4
3. Connectors Diagram
3.1 Configuration Pictures
: Power adapter DC 5V :Audio-out port
:Power LED (Solid Red when power present) :Local VGA monitoring
:Link LED (Solid Green when link present) :VGA source
:IR Emitter control port :Audio-in port
: RS232 control port :RJ45 CAT.5e/6 UTP port
: Power adaptor DC5V :Audio-out port
:Power LED (Solid Red when power present) :VGA output ( remote display)
:LINK LED (Solid Green when link present) :RJ45 LINK
:IR receiver control port :RJ45 LINK
: RS232 control port :RJ45 LINK
Transmitter(TX)–FrontView Transmitter(TX)–RearView
Receiver(RX)–FrontView Receiver(RX)–RearView

5
Application Diagram
Transmitter (TX) Installation
Please use CAT.5e/6 cable to get the best quality to connect to
the LINE port (RJ45) of Transmitter
Connect the IR Blaster Emitter cable or RS-232 to 3.5mm adapter to the Transmitter Unit IR
Port or RS-232 port if necessary
Connect Transmitter with VGA cable to a VGA source
Connect Transmitter with VGA cable to a VGA monitor
Connect DC 5V power adapter
Connect to UTP cable
Connect to local VGA monitor
Connect to local speaker Connect to VGA source
Power Adapter 5V Connect to audio source

6
Receiver (RX) Installation
Please use CAT.5e/6 cable to get the best quality to connect to the LINE1 or LINE2 or
LINE3 port (RJ45) of Receiver
Connect the IR Receiver cable or RS-232 to 3.5mm adapter to the Receiver Unit IR Port or
RS-232 port if necessary
Connect Receiver with VGA cable to a VGA monitor
Connect DC 5V/2A power adapter.
Cascade Chain Connection
Use UTP Cable to connect with Receiver to link the other two Receiver Units consecutively
for extending another 100m distance, the cable is to connect to Receiver LINE1 or LINE2
or LINE3 port (RJ45), as long as the LINE port is not occupied, and user can continue
expanding corresponding to custom demand as likely Cascade/Tree Chain web
architecture spread
Connect the IR Receiver cable or RS-232 to 3.5mm adapter to the Receiver Unit IR Port or
RS-232 port if necessary
Connect Receiver with HDMI cable to HDMI connector of Display Monitor
Connect DC 5V power adapter
4
Connect to VGA monitor
Connect to speaker
Power Adapter 5V Connect to UTP cable
Connect to VGA monitor
Connect to UTP cable
Connect to speaker
Power Adapter 5V

7
Each Receiver with three Line port, one is used for source input; others are used for expanding
source to other receivers. User can choose any LINE port as source input random and use the
other two LINE port for expanding source to next tier receiver as long as the LINE port is not
occupied.
Network Switch Extending
The maximum distance between each tier could be up to 100 meters long, while this could
be extended through Network Switch. User can add one Network Switch to extend another
100 meter
The more Network Switches, the longer distance extended. The number of Network
Switches can be as many as user want

8
3.2 Connection Diagram
(1) Single Source Extension
(2) Single Source Extension and Receivers Cascade Chaining
(3) Single Source with Multiple Receivers Cascaded
VGA Cable

9
Cascaded and mixed with VGA / HDMI / DisplayPort
IR Bypass function connection
Connect the IR Transmitter (or Emitter) cable to the IR Connector on the Transmitter (TX)
Connect the IR Receiver cable to the IR Connector on the Receiver (RX)
Place the IR Eye of the IR Receiver cable near the Remote Controller
Place the IR Blaster of the IR Transmitter cable near the device that intend to be controlled
by the Remoter controller
V
GA Out
VG
A
VG
A

10
3.3 RS-232 Bypass function connection
Connect the device, such as a PC, projector…etc, to the RS-232 port of the Transmitter or
Receiver via a RS-232 to 3.5mm adatper
Connect the controlling device to the RS-232 port of the Receiver or Receiver via a RS-232
to 3.5mm adapter