Digitus DN-95127-1 User manual

Gigabit 4PPoE Extender,
60W, 2 ports
Manual
DN-95127-1

1
Product introduction
The DIGITUS® Gigabit 4PPoE Extender supports the latest networking technology to
extend your Ethernet signal to up to 100 meters. The extender is powered by
4PPoE (4-Pair Power over Ethernet or lower), so you do not need an additional
power adaptor and can use the device, even where there are no power cables or
sockets, to significantly increase the network range. With the PoE+ and 4PPoE
support, you can also connect devices with higher power consumption, such as
access points, POS systems or video telephones. Choose future-orientated 4PPoE
technology with the Gigabit 4PPoE Extender from DIGITUS®.
Front panel
The front panel consists of LED indications and network ports.
PoE Ports:
•PoE IN: Meets the following standards: IEEE802.3af (PoE), IEEE802.3at
(PoE+), IEEE802.3at (4PPoE)
•PoE OUT: Meets the following standards: IEEE802.3af (PoE), IEEE802.3at
(PoE+)
LED Lamp:
•Link/Act indicator: the light indicates the network connection through the
corresponding port.
Flicker indicates that the extender is sending or receiving data
•SPD indicator: when it lights, it indicates the link through that port is
successfully established at 1000Mbps. Otherwise, it will be off but still
functioning.
•PoE indicator: constant brightness indicates that the PD device is
connected to the corresponding port, and extinguished indicates that the
port is not powered or no PD device is found.

2
Real panel:
Hardware installation
This chapter provides unpacking and installation information for the unmanaged
PoE Extender.
First step: open a seal
Open the shipping carton and carefully unpack its contents. Please consult the
packing list located in the User Manual to make sure all items are present and
undamaged. If any item is missing or damaged, please contact the local reseller for
replacement.
•PoE extender 1pcs
•User manual 1pcs
Second step: installation
For safe installation and operation, it is recommended that you:
•Make sure that there is proper heat dissipation and adequate ventilation
around the device.
•Do not place heavy objects on the device.
Desktop or Shelf Installation
When installing the extender on a desktop or shelf, the rubber feet included with
the device must be attached on the bottom at each corner of the device's base.
Allow enough ventilation space between the device and the objects around it.

3
Network connection

4
Technical specifications
Summary
Fixed port
2x10/100/1000Mbps PoE OUT ports
1x 10/100/1000Mbps PoE IN ports
Standards and protocols
IEEE802.3 10Base-T Ethernet standard
IEEE802.3u 100Base-TX Fast Ethernet standard
IEEE802.3ab 1000Base-T Ethernet standard
IEEE802.3z Gigabit Ethernet (fiber)
IEEE802.3x Full duplex flow control and
Backpressure Half duplex flow control
IEEE802.3ab Link aggregation
Forwarding Rate
10/100/1000Mbps
LED Indicators
Link/Act, SPD, PoE
Operating temperature
0°C～40°C
Storage temperature
-10°C～70°C
Relative humidity
20%～85% (non-condensing)
Exchange capacity
6G
MAC Addresses
2K
PoE Technology
PoE Compliance
100% IEEE 802.3af, 802.3at compliant
PoE Classification
PSE (Power Sourcing Equipment)
PoE Voltage
+52 VDC
PoE Power Budget
30W - 60W
PoE Power
Up to 30 W per port
PoE Operation
Automatic detection and power management
PoE Pin Assignments
V+ (Pin 1, 2), V- (Pin 3, 6)
PoE IN
Compatible with IEEE 802.3af/at
0 - 5 PoE rating
Traditional 36V UVLO
Current limit and foldback protection
Overheating protection
Mechanical
Casing
Metal
Dimensions (W x L x H)
130mm x 86mm x 29 mm
Installation
Desktop

5
This is a Class A product. In home environment, this product may cause radio
interference. In this case, the user may be required to take appropriate measures.
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is
part of the shipping content. If the Declaration of Conformity is missing, you can
request it by post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany