Digitus DN-16100-2 User manual

H.264 Multi-Profile
1-Channel Video Server
Quick Start Guide
DN-16100-2

2
About multi-profile
Multi-profile stands for simultaneously video streams. These Network Cameras can generate H.264, MPEG4
and MJPEG streaming simultaneously to different clients. Moreover, the resolution can be different from
one client to another. This state-of-art design is considerable to fit in various network environments.
Before Installation
Before installation, please be sure to read this quick installation guide and user’s manual carefully to
complete machine installation.
1. System Requirements
System Requirement for Viewer & Recorder Application
Support OS Win XP, Vista, 7
FPS
(QVGA)
~120 120~360 360~540 540~960 960~
CPU Intel P4
2.4GHz
Intel P4
3.2GHz
Intel Pentium D
950
3.4GHZ
Intel core 2 Duo
E8600
3.3GHZ
Intel core 2 Quad
Q9650
3.0GHZ
RAM 512MB 512MB 1GB 2GB 2GB
Display support1024x768 resolution or above
Support DirectX 9.0c or above
Intel 945G or Intel 965G or above
Hard disk 60GB (free space)
Ethernet 100Mbps 1Gbps
Chipset Intel 945 or Intel 965 or above
H.264 Multi-Profile 1CH Video Server
Network Environment
Network Interface 10/100MBase-TX Ethernet
Monitoring System Recommended for Internet Explorer 8.0 or later
System Hardware · CPU: Pentium 4, 3.6GHz or higher
· Memory Size : 1GB or more
· VGA card resolution : 1024 x 768 or higher
- Sound card: for 2-way audio function
System Requirement for Viewer & Recorder Application
Support OS Win XP, Win Vista, Win 7, Win 8
System Hardware 16 cameras surveillance application (typical)
· CPU: Intel Core 2 Quad 3GHz or higher
· Memory Size : 2GB or more
· VGA card resolution : 1024 x 768 or higher

3
2. Physical Installation
2.1 Connections
Front Panel
LAN Socket
The LAN socket is a RJ-45 connector for connections to 10Base-T or 100Base-TX Fast Ethernet
cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission speed of
the network automatically. Please use Category 5 cable to connect the Video Server to a 100Mbps
Fast Ethernet switch or hub.
In the LAN socket, there are two LEDs embedded:
LAN LED (green color)
This LED will be flashing while network accessing via Ethernet.
Power LED (orange color)
This LED is used to indicate whether DC power is on or not.
Video-in Jack (BNC connector)
You can Install 1 video camera and connect it to video-in jack.
DI/DO/RS485 Connector
The Video Server provides a terminal block with 6 pins of connectors for DIDO and RS485. Please
refer to the Appendix A in this manual for more information.
Cable for I/O connectors:
Name Number Function
VDC 1 12V DC output (300mA maximum)
DI 2 Digital signal input
GND 3 GND
DO 4 Digital signal output
485+ 5 RS485 data +
485- 6 RS485 data -

4
Back Panel
MIC in (audio in)
Connect an external microphone to the Video Server.
Micro SD Card Slot
User can insert a micro SD card into this slot for recording.
Factory Default Reset
This button is hidden in the pinhole. This button is used to restore the all factory default settings.
Sometimes restarting the Video Server will make the system back to a normal state. If the system
still got problems after restart, user can restore the factory default settings and install it again. To
restore the device, please follow the steps below:
(i) Insert the paper clip or any proper tool and press and hold the button down
continuously.
(ii)Hold it at least 5 seconds and release the tool. Then the device has been restored
to default settings and reboot again.
Note: Restoring the factory default setting will lose the all previous settings included IP address
forever. User needs to run the IPWizard II program to search the device and configure it to let the
device work properly again.
Audio/Video Output Jack
Audio/Video-out Jack allows this device to output audio and video signal. Use the attached A/V
cable to connect A/V device where white cable is for audio and yellow cable is for video.
DC Power Jack (12VDC out)
2.1.1 Installation
1. Attach video source to Video Server
To use this video server, user must supply video source to this device first. Typical, user may utilize
box camera, doom camera, bullet camera, P/T/Z camera, Speed doom camera, or others as the
video source. Connect an external camera to the device’s video input and make sure to power on
these cameras first. Otherwise, the operation may be incorrect.
2. Attach external microphone to Video Server (option)
If user needs not only video stream but also audio stream, then an external microphone should be
attached to Video Server. Connect an external microphone to the Video Server’s audio input.

5
3. Plug an Ethernet cable into Video Server
Connect an Ethernet cable to the LAN socket located on the device’s panel and attach it to the
network.
4. Connect RS485 (option)
When users would like to apply a camera with P/T/Z function, they usually need to connect their
communication port (for camera control) through RS485. After RS-485 was correctly connected to
D+ and D-, the remote users could control the camera movement through Internet.
5. Connect an external power supply to Video Server
Connect an external power supply to the 12VDC power jack of the Video Server. Once you have
installed the Video Server well, the Power LED (orange) will turn on later. It means the system is
booting up successfully. Furthermore, if you have a proper network connection, and access to the
Video Server, the LAN LED (green) will flash.
6. Connect DC power to one external camera from Video Server (option)
In case your Video Server is connected to PoE switch, then this device can provide 12VDC out to
supply one external camera thru 12VDC power jack. Note that the output current is 300mA
maximum.
7. Done
3. Camera administration
When you installed your networked device over your network environment, to start Network
Camera web configuration, you must have the web browsers installed on computer for web
management.
-Microsoft internet Explorer 6.0 or higher
At first, user may use “IP Wizard II” utility to search all networked devices in the LAN.
Use “IP Wizard II” to locate IP address
Press “Search” button. IP Wizard II will list all networked devices in the LAN:

6
View function:
If IP Wizard II finds network devices, View button will be available. Please select the device you
want to view and click the View button. Furthermore you could double click the left button of
mouse to link to the network device by browser.
3C:49:37:07:01:02
3C:49:37:07:01:02

7
LAN setting function:
The utility featured with “LAN” setting function to help user to modify the IP parameters of the
installed network devices. User can step by step to setup IP address, username and password.
Note 1: If no IP address is assigned within 30 seconds, the networked device will automatically
assign 192.168.0.100. User may now open your web browser, and key in http://192.168.0.100 in
the address bar of you web browser to logon Network Camera’s web configuration page.
Note 2: Power Line Frequency
-If you found the video image is flash, you may need to choose 50 or 60 Hz frequency
(depends on country).
-World wide power line frequency table is inside user’s manual, Appendix
Note 3: If you have problem when connecting the network camera to a router, please read user’s
manual inside CD, the section “Installation to a router”.

8
After connected to networked device, the device will prompt for User name and Password. For the
first time, please enter: “admin” as username and password: “admin” to continue Web
Management.
If difficulty is met, please refer to the following steps to establish the connection:
-The networked device must be installed and powered ON.
-If the networked device’s default IP Address (192.168.0.100) is already used by another device, the
other device must be turned OFF until the device is allocated a new IP Address during configuration.
Hereby ASSMANN Electronic GmbH, declares that this device is in compliance with the requirements of
Directive 2014/30/EU (EMC), Directive 2014/35/EU (LVD) and the Directive 2011/65/EU for RoHS compliance.
The complete declaration of conformity can be requested by post under the below mentioned manufacturer
address.
Warning:
This device is a class B product. This equipment may cause some radio interference in living environment. In
this case, the user can be requested to undertake appropriate measures to prevent interference.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany