Digitus DN-95347 User manual

PoE+ GIGABIT
ETHERNET SWITCH 2x SFP
Manual
DN-95347 (16 port) • DN-95348 (24 port)

2
Package Content:
Please open the switch package carefully, confirm the packing box should be as follows:
• 1x Unmanaged Switch
• 1x power cable
• 1x User Manual
• 2x mounting brackets
• 4x mats
• 6x brackets screw
Note: Rack type models are built in power, no power adapter, and desktop type inorganic
rack mount accessories (mounting brackets / brackets screw).
Introduction
The DIGITUS® PoE+ Gigabit Ethernet Switch 2x SFP provides a simple way to expand a
wired network by transferring power and data over a single Ethernet Cable. It can power
more high-powered devices such as wireless Access Points (APs), IP Cameras or IP Phones.
Moreover, with innovative energy-efficient technology, the Switch can save up to 75% of
the power consumption, making it an eco-friendly solution for your business network.
Parameter
• The CPU frequency of 500 MHz, 4M cache.
• Works with IEEE 802.3af/at compliant devices, expanding home and office
networks
• Innovative energy-efficient technology reduces power consumption by up to 75%
• Plug and play design, no configuration required

3
Product Display
Front panel sketch map
1. DN-95347: 16x 10/100/1000M PoE Port + 2x 1000M SFP, Rackmount, 19-inch steel case
2. DN-95348: 24*10/100/1000M PoEPort+2*1000M SFP, Rackmount, 19-inch steel case
PWR: The indicator lights up to indicate that the switch is connected
to the power supply
SYS: CPU state indicator light after the initialization is completed,
per-second flicker once
Giga/1000M: The transmission rate of the corresponding port is 1000M
Link: Data transmission on the corresponding port
VLAN: DN-95347: Ports 1-14 are isolated from each other.
VLAN ports can only access ports 15-18.
DN-95348: Ports 1-22 are isolated from each other.
VLAN ports can only access ports 23-26.
Back panel sketch map
The 19-inch steel case, back panel sketch map
Power adapter interface: The power supply of the switch is inserted into the
port, insert additional adapter
Single phase three wire socket: The power supply of the switch is inserted into the
port, and the input voltage of AC terminal is 100-
240V 50/60Hz
Grounding: Make the equipment ground

4
Product mounting
Attention
In order to avoid improper use of equipment damage and personal injury, please note the
following:
1. During the installation, the power supply remains closed, while wearing anti-static
wrist, and ensure that anti-static wrist and skin good contact, to avoid
potential safety Hidden danger;
2. The switch can work normally under the correct power supply. Please confirm that
the supply voltage is consistent with the voltage indicated by the switch;
3. Before the switch is switched on, please confirm that it will not cause overload of
the power circuit, so as not to affect the normal operation of the switch or even
cause unnecessary damage;
4. In order to avoid the risk of electric shock, switch work should not open the shell.
Even in the case of no electricity, do not open on its own;
5. Before cleaning the switch, the switch power plug should be pulled out. Please do
not wipe with wet fabric. Please don't use liquid cleaning;
6. Install the equipment rack generally from the bottom. Avoid overload installation;
7. The switch surface to avoid placing other heavy objects, so as to avoid accidents
Mounting Switch
Rack Mounting
1. Check the grounding and stability of the rack.
2. Secure the supplied rack-mounting brackets to each side of the device with
supplied screws, as illustrated in the following figure.
3. After the brackets are attached to the device, use suitable screws (not provided) to
secure the brackets to the rack, as illustrated in the following figure.
Figure 2-1 Bracket Installation
Figure 2-2 Rack Installation

5
Desktop mounting
To install the device on the desktop, please follow the steps:
1. Set the device on a flat surface strong enough to support the entire weight of the
device with all fittings.
2. Remove the adhesive backing papers from the rubber feet.
3. Turnover the device and attach the supplied rubber feet to the recessed areas on
the bottom at each corner of the device.
Connect Port
Connect Ethernet port
Connect an Ethernet port of the switch to the device by RJ45 cable.
Connect SFP port
The optical fiber module is grabbed from the side and inserted smoothly along the switch
SFP slot until the optical module is in close contact with the switch.
Note: To avoid improper operation cause damage to equipment or personal injury, please
pay attention to the following matters
• Excessive bending of optical fibers is not allowed, and the radius of curvature
should not be less than 10cm.
• Ensure the cleanliness at the end of the fiber.
• Please do not look directly at the optical fiber connector; otherwise it may cause
damage to your eyes.
Remarks: It is recommended to adopt straight line -568B international standard
connection method, as the following figure shows
Figure 3-3 Network line making

6
Power supply socket specification
Switch power line single-phase three wire power socket, the middle foot to ground, and
the left foot on the right foot for the zero line and FireWire, please check before the
operation.
E
N
L
Connect the power cord
1. Check the selection of power supply and the switch marking requirements;
2. Desktop power input DC output terminal into the switch DC port, then connect the
power line to AC100~240V, 50~60Hz power;
3. The Rack mount type without power adapter, direct access to AC100~240V,
50~60Hz city electricity
Figure 4-2 Adapter connection
Figure 4-3 Power core connect
1
2

7
Connecting to the Ground
The grounding cable is important to protect the switch from electrical interference. It is
advised to use the grounding cable; if your power is ungrounded which could damage the
switch or its functionality
Figure 4-4 Connecting Grounding Terminal
Note: The grounding bar and the ground cable are not provided with our product. If
needed, please self purchase them.
Check after installation
Please check the following items after installation:
1. Check whether there is enough space for heat exchange, air circulation is smooth;
2. Check the power supply socket power supply switch is in accordance with the
specifications;
3. Check the power supply, switchboard, rack and other equipment have been
properly grounded;
Grounding Terminal

8
PoE Switch Hardware Parameters
Type
DN-95347
DN-95348
Port
16x 10/100/1000 M
24x 10/100/1000 M
SFP
2x SFP
2x SFP
POE standards
IEEE802.3af/at, single port PoE power 30 W
POE Port
16
24
PoE Budget
380W
Bandwidth
36 Gbps
52 Gbps
Packet forwarding
26.78 Mpps
38.69 Mpps
CPU
500 Mhz
RAM
128 M
MAC
8 K
buffer
4.1 M
FLASH
128 M
Transmission
Store and forward
working temperature
0°C ~ 50°C
Storage temperature
-40°C ~70°C
Operating humidity
10 % ~ 90 % Non-coagulation
Storage humidity
5 % ~ 95 % Non-coagulation
Product size
440 x 290 x 45 mm
440 x 290 x 45 mm
Packing size
497 x 313 x 97 mm
497 x 313 x 97 mm
Power in
AC 90~265 V 50/60 Hz
Power
400 W
Hereby Assmann Electronic GmbH, declares that the Declaration of Conformity is part of the shipping content. If the
Declaration of Conformity is missing, you can request it by post under the below mentioned manufacturer address.
www.assmann.com
Assmann Electronic GmbH
Auf dem Schüffel 3
58513 Lüdenscheid
Germany